More Sig Mags. P226 9mm, P229 40/ 357 sig and P229 9mm Mags, Sig Holster for p229r, p226 hogue rubber grip
By
bry@n, in Experience/Feedback
-
Recently Browsing 0 members
No registered users viewing this page.
-
Supporting Vendors
-
-
Latest Topics
-
-
Similar Content
-
By ivstealth
I want to sell my P229R with a DAK Trigger. It comes with three magazines. Doesn't jam and has never let me down. Night sights usually are crap on these... This ones clean.
$500, fees covered by you. I will work with you to meet up locally or travel a little. I'm near Clifton, NJ. Exchange will be made at a local FLL dealer. Valid FID and license required.
-
By crazyboy
Cleaning out some unused gear.
Everything listed is in new condition. Purchased to try on, and never left the house. Unfortunately it is past the return time frame.
Located in Ocean County, but would prefer to ship due to scheduling. Will ship via USPS Priority Mail, Flat Rate Padded Envelope at no charge. Don't hesitate to make reasonable offers.
The first person to say I'll take it to a particular item gets it.
Item 1 -
Vedder Holsters Rapid Tuck
IWB Hybrid Holster
Right Handed
Fits Sig P365 with TLR6 attached.
Steel Spring Clip for 1.5" Belts
Hand Molded Kydex and Cowhide.
Sells for $69 plus shipping, looking to get $59.
Item 2 -
Vedder Holsters Quick Draw
OWB Hybrid Holster
Right Handed
Fits Sig P365 with TLR6 attached.
Belt openings fit belts up to 1.75"
Hand Molded Kydex and Cowhide.
Sells for $79 plus shipping, looking to get $69.
Item 3 -
Alien Gear Shape Shift
Springfield XD9SC Shell
Alien Gear Shape Shift OWB Slide Holster
Right Handed
Sells for $63 plus shipping, looking to get $52.
Item 4 -
Alien Gear Single Cloak Mag Carrier
9mm/.40
Fits XD9 Mags, unsure what other mags are designed to fit.
Convertible between IWB and OWB.
Sells for $41 plus shipping, looking to get $30.
-
By gunguynj
So Im moving out of state and the law there says I can only have a MAXIMUM of 10 rounds in my magazine. Problem is I have 4-6 15 round magazines for a Sig Sauer p226 9mm. I called the Bullet Hole and Sig Sauer direct and they said they couldnt modify the magazine. So my question is, what can I do with my current magazines: sell them and buy 10 round magazines or can they be modified?
Thanks
GGNJ
-
By Gunnz
Bought the p226 Classic a few years ago, and have put off buying the 9mm conversion since then...
I work hard, and have decided to give myself a Christmas present and buy one...
I know shore shot has them, and I rather not give them my money, anyone see them sold local?
Anyone seen a good deal for them online?
Looking to buy ASAP!
-
By HBecwithFn7
I was at an outdoor range, yesterday with my 2A mentor. I loaded up my P226 (it's been a while since I've shot it) with some AE 147gr flat heads.
"Goin' Hot..," and then.... "Click...." nothing.....
I wait to ensure it wasn't a hang fire, then cleared the weapon and ejected the round. Sure enough there was a light depression in the primer. I tried again, and "click...." nothing...
My mentor loaned me some standard AE 115Gr round nose. I loaded up two of those. And, lo and behold, they fire without issue! Then I tried some of my Hornady "Critical Duty" rounds. First round.... BANG! No problem. 2nd round..... ."click......" Ruh-Roh..... As before, a light depression in the primer. One more time with Hornady and..... "click....." nothing! I try the flat heads in my Shield, and "BANG....BANG...BANG..." all fires, no issues.
So, I'm thinking, maybe a "sticky firing pin" in the P226? Perhaps a more detailed cleaning is in order? Or is this something that may require a bit of smithing?
FTR, my P226 is the only one of my inventory that I cleaned initially with "Froglube." My mentor has soured quite a bit on FrogLube, now. The other of my inventory has been cleaned with Hoppes 9 and Hoppes std. oil, along with gun grease for the rails.
Anyway, all help truly appreciated, since I have to use this gun later this month for my MAG-40 class. If I'm going to need smithing, I need to know ASAP. I also need to find a good gunsmith that does P226's in the Gainesville FL area.
Thanks much all.
-
-
Posts
-
Looking to buy some non-corrosive 7.62x39. I'm located in Bergen County. Please let me know if you have some at a decent price.
-
ff to approx 1:20. sped up this looks like a controlled turn. hopefully it wasn't.......
-
watch this video. there were at least 4 stationary construction vehicles.
-