ADK1113

I couldn't find anything specific to your question in NJ Llaw. However, there may be a case against you for constructive possession. But the ambiguity of the law works both ways, YMMV, I've had them shipped to my house before, but that's my decision, and I converted them to 15/30s straight away. Sent from my XT1254 using Tapatalk

+1 for howard leights. I've used em in doors and outdoors..no problems. In my unit I use peltors cus they have split PTT for two different comms channels in each muff. Sent from my XT1254 using Tapatalk

Why do you have a weapon that wasn't legally trasferred anyways? Sent from my XT1254 using Tapatalk

What? What registry? Sent from my XT1254 using Tapatalk

Looks like one of those homemade chechan designs Sent from my XT1254 using Tapatalk

exactly.it offends the sensibilities of others. i find enjoyment in that

Thanks boss man! Also: just for posterity, that's a 15/40 round magazine for the mini 14. I just like seeing everyone stare when I go to the range. Haha Sent from my XT1254 using Tapatalk

Sent from my XT1254 using Tapatalk

I agree because there is no transfer actually taking place it should be able to be shipped right back to you Sent from my XT1254 using Tapatalk

Hell send 'em my way And I'll review em for ya! And Sage Dynamic is running a class in NJ this weekend. Too bad it conflicts with my personal schedule. Sent from my XT1254 using Tapatalk

Not bad. I'd suggest setting up a gopro or some sort of recording device and record yourself shooting it from a third person perspective that way you can go back and review and see what you're doing wrong. Breathing, trigger squeeze, not maintaining a stable shooting platform, flinching, trigger reset can all be ascertained by 2 cameras one close up.and one a little farther back. Sent from my XT1254 using Tapatalk

Can you direct me. Sent from my XT1254 using Tapatalk

how do you like the joe bob lower? any issues with magazines not dropping freely?

thanks appreciate your response did it help with vertical stringing from the barrel heating up?

Thanks man! Trying to decide between the accu strut, the mo-rod Sent from my XT1254 using Tapatalk

Cold steel inferno makes a .38 oz one or a 1.3 oz. I can attest from person experience that.it is excruciatingly painful. Sent from my XT1254 using Tapatalk

I've had a question.about that. It looks like 2 small clamps attached to a rigid piece of tubing. You think a DIY version.would be effective? Sent from my XT1254 using Tapatalk

you seem to think that 1.5 inches makes a huge difference in accuracy. i think this explains much "http://www.thetruthaboutguns.com/2013/10/daniel-zimmerman/the-truth-about-barrel-length-muzzle-velocity-and-accuracy/" and as counter-intuitive as it may seem, a shorter barrel in a pre 580 series Mini 14 has had smaller groups on multiple tests as can be seen on forums such as Perfect Union and the Ruger Forum, The thin pencil barrel of the pre 580 Mini 14s flexed a great deal. a shorter stiffer barrel helps negate that dramatically. realistically this rifle won't be taking shots past 150M-200M anyways, a distance at which I've regularly tagged with 11in. SBRs... So the argument of a 14.5 inch barrel being less accurate than a 16 inch barrel at that distance is academic. and to be frank, a loss of 150 FPS, (and several tests have put it as low as 57 FPS difference), is not a huge consideration for me. however having a Muzzle device that helps reduce as much recoil and flash as possible is important as I've previously described the situation. If you read my first post on this thread, I actually wanted a FH which does help mitigate SOME recoil instead of a traditional muzzlebrake, which is still better than nothing. that being said even a Muzzlebrake such as a Mod 0 does a relatively effective job of redirecting the noise and flash away. instead you seem to keep pressing for 16 in. bare barrel, and anything other than that is "Tacticool". there are MANY practical applications for Flash hiders, compensators and muzzlebrakes. But I'll bow to your greater judgement, I guess we should rip off the FH's from the M4's, SAWs, 240's and the muzzlebrakes from our Barrets and m2010s at my unit. all kidding aside, thanks for your responses everyone, I appreciate the help and I'll be contacting Tier 1 soon. is there any other gunsmith Forum regulars would recommend for a barrel chop and Pin/weld?

Haha it WAS a 40 rounder when i lived in VT (one of the most gun friendly states. n the union). When i came back i cut up a block of delrin and epoxied the mag plate. The looks I get at the range makes it worthwhile hahaha Sent from my XT1254 using Tapatalk

Yeah, sorry about that, got any idea where I can find a smith who'd do a cut and pin/weld job for a fair price? Sent from my XT1254 using Tapatalk

I HIGHLY recommend the Primary Arms Advanced Microdot. Sent from my XT1254 using Tapatalk

Very nice! Sent from my XT1254 using Tapatalk

Well never the less that's still an extra 2 inches I need lopped off. As of yet i haven't got an answer to my question. I do appreciate the responses though gentlemen. In a research article presented by by Dr. Philip H. Dater & Jason Wong on 8 February, 2012 from the small arm defense journal presents a similar result. Fig 1. Shows the decreasing velocity of the M855 cartridge starting from 20 in. All the way down to 5 inches. As can be seen a 16 in. Barrel has about ~150 FPS increase compared to a 14.5 n barrel. For my purposes a 150 FPS loss is acceptable if I can mitigate As much flash and recoil, I'm thinking of something like a BCM mod 0. My father is getting back into shooting, he's been ill and frankly is old. I'd rather have him be able to shoot a weapon accurately at the cost of some FPS than have difficulty hitting his targets. I'd rather thread a 16 in barrel but with his short stature I'm trying to have the weapon as short as possible and still stay above the 2500 FPS mark to balance out comfort and effectiveness. Sent from my XT1254 using Tapatalk

Good point. Will consider it. Know anywhere that'll do it for a fair price? Sent from my XT1254 using Tapatalk

I think something was lost in translation friend. The picture you see is the BEFORE picture. The gentleman I bought the rifle from chop the barrel and tack weld it that ginormous flash hider to it. Since then it has been read barrels with a full length 18.25 inch ruger mini 14 barrel. My intention is to have the barrel cut and 11° crowned at roughly 14.5 inches to allow for an A2 style flash hider or similar muzzle device of a similar size to be permanently affixed to the barrel to put it just over 16 inches Sent from my XT1254 using Tapatalk