SW99

Yeah. I did that too. Thanks should be going back to the range again this week and see if there is any improvement. Feels a bit better during the test unlike before I pulled it all out.

thats how i had it. took it all out and put it all back in. lets hope it helps, fingers crossed

fat side down right?

lol, Im looking at those triggers now, they can get a bit pricy

You think just a new disconnector or entire trigger assembly?

I keep playing with it and noticed it happens a lot when i let the trigger out very slow but not when i just let it go.

I added pictures of the LPK that i took before i installed it, hope that helps. http://gallery.me.com/vvacca#100222

Should i put a little lube and see if that helps?

PM returned!

Is a DSA (dsarms.com). So i did the test in this video (at minute 10:50) which is what you guys were saying to do. When i push the hammer back (still holding the trigger) and let go of the trigger slowly like the guy says in the video, sometimes its getting stuck, and not popping back up slightly like it shows in the video. (at 11:20 in the video) so it seems like this is my problem?

More pics http://gallery.me.com/vvacca#100222

I'll get some more pictures up in an hour or so. The rounds are clambering fine, trigger just seems to lock up after 2-3, 5 shots, then I clear it, and it's fine again for a few more rounds.

http://gallery.me.com/vvacca#100214 My rifle is setup for a righty shooter, but I shoot long guns lefty so my thumb can't be hitting the safety.

Thanks alowerlevel. I did copy and paste it from the site. My entire AR is NJ spec, specifically ordered it that way, stock and all so I didn't have to worry about being out of NJ spec (not that they would have shipped it to me) and pinning anything. Sorry for the confusion above.

Thanks for the help so far! I just pulled the BCG and cleaned and lubed in the recommend spots (dried and cleaned firing pin). Im going to try to go again on thursday to see if that helped and to pay closer attention to the things you mentioned Vlad. The ammo can be ruled out?

Thanks for the answer on the Charging handle, after thinking about it, it makes sense. lol As for the first problem. The round would chamber like i said above but when i went to pull the trigger it wouldn't do anything, no movement at all, almost like it was being blocked as if the safety was on. After pulling the chugging handle and the round in the changed ejected, it would then chamber a new round and it would work fine again for a few rounds. Hope this helps. Thanks again!!

So I took my brand new AR out for a small test drive today. I only put 40 rounds through it. I ran into 2 problems: First problem was, I would get 2-3-4 rounds out with no issues then a round would chamber (bolt fully closed) but when I went to go pull the trigger nothing would happen. I would have to pull the charging handle to eject the unfired round in the chamber and chamber the next round, then it would be fine. This happened a few times with both mags throughout the session. Second problem, when ever I would shoot the last round in the mag the bolt would catch open as it should, but the charging handle would stay in the closed position. When you shoot the last round and the bolt catches open isn't the charging handle supposed to also be fully open? The ammo I used was 5.56mm (62) FMJ M855 Penetrator (green tips) 20 rounds of this (This box cost me $11, as i bought it last week and brought it with me today) I also used 20 rounds of something else (forgot to save the box) I do know it was 5.56 for sure not .223 as the person behind the counter asked if i could shoot 5.53 ammo and thats what she game me. It was in a brown box and cost $9. (this box i purchased today) Here are the specs on my upper: Stag-15 Model 2H Pre-Ban Caliber....5.56 Nato Chamber Upper......Forged and Mil Spec. Sights..... Flip Up Rear/Front Post Barrel.....16" Chrome Lined 1/9 Twist Break......A2 Flash Hider Anyone have any ideas as to whats going on? Is it the ammo I'm using? If so what should I be using? I know you can shoot .223 rounds in a 5.56 chamber (but not the other way around) should I be using .223 instead? Other than the above it shot great. at 23 yards out slightly 4 o'clock of center mass. Im looking to get it on a 100yrd outdoor range soon and will see how it is at at range. Thanks for all the help!!

Stag makes a factory pinned NJ spec 6 position style stock. Thats what i have on mine, good length and looks great. The entire kit cost me 69 shipped

Thanks guys! I can't wait to shoot it. Waiting on a friend to bring by the stock wrench so it can be fully complete. I'm sure my first time shooting it will be at the bullet hole as its 2 min away from me. I would really love to shoot it outside on a 100 yd range but gotta find one. I was there last Friday Mark around noon and I was one of 3 people on the range. Just went for 30 min to shoot off some 9's and 45's.

The final parts came in today so here she is: DPMS Lower Receiver DSA Lower Parts Kit Stag 2H Upper Receiver with Rear Fold Down Stag NJ Compliant 6 Position Style Stock 2X PMAG 15/30

Completed Updated the first post!

The PMAGS are in, added pics to first post. Now just waiting on the Upper and Stock, should be any day now.

I got 2 PMAG's 15/30 for 48.97 shipped at riflegear.com

I'm in the process of building my first one and had the same fear. There are a lot of helpful people on here so pick their brain, I have. Also check out AR15.com for info, a wealth of knowledge there. As for price my entire build cost just over $800 128 for the stripped lower (DPMS) 65 for the LPK 69 for a pined 6 position style stock 499 for a stag complete upper H2 with rear fold down sight 49 for 2 PMAG's 15 rounders in a 30 rd body. The prices include tax and shipping. Only the lower is complete so far, waiting on the upper, stock and mags. This was to get me up and running but I will be adding things as money allows such as optical sight, forward handle, flashlight mount, etc.

Just ordered a Stag Complete Upper Model 2H and Pinned Stock. It should be here in a couple weeks.