Jump to content

Recommended Posts

*SOLD*

 

A few basics:

  • LOWER RECEIVER: Mil-Spec with Enhanced Flared Magazine Well and Rear Receiver QD Swivel Attachment Point. CNC Machined of 7075-T6 Aluminum, Type III Hard Coat Anodized
  • UPPER RECEIVER: Mil-Spec with Indexing Marks and M4 Feed Ramps. CNC Machined of 7075-T6 Aluminum, Type III Hard Coat Anodized
  • BARREL: Chrome Moly Vanadium Steel, Cold Hammer Forged, 1:7 Twist, 16" Government Profile, Mid-length Gas System, Chrome Lined, Mil-Spec Heavy Phosphate Coated, and HP/MPI Tested
  • GAS SYSTEM: Pinned Low Profile Gas Block CNC Machined of 4140 hardened steel and Mil-Spec Heavy Phosphate Coating, Mid-length, Direct Impingement
  • HANDGUARD: Daniel Defense MFR 15.0, CNC Machined of 6061-T6 Aluminum, M-LOK Attachment, Type III Hard Coat Anodized
  • RECEIVER EXTENSION: 6 Position Mil-Spec 7075-T6 Aluminum
  • BUTTSTOCK: Daniel Defense Buttstock, Glass Filled Polymer with Soft Touch Overmolding
  • PISTOL GRIP: Daniel Defense Pistol Grip, Glass Filled Polymer with Soft Touch Overmolding
  • Ambi Safety.  Mil-Spec CH.
  • Made in the USA!

Must have matching DL and FID.  All required docs and fees by your FFL are on you.  I am in Bergen County.  If local to Bergen County (or relatively close), I can drop off the item in the original DD plastic case to the agreed upon FFL.   Thanks.

sgdasdga.jpg

asdfasdfasd.jpg

djgfjdgf.jpg

asdfasdfads.jpg

fjfgjdfg.jpg

  • Like 3

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.

  • Recently Browsing   0 members

    No registered users viewing this page.



  • olight.jpg

    Use Promo Code "NJGF10" for 10% Off Regular Items

  • Supporting Vendors

  • Latest Topics

  • Posts

    • In 50 years of living in NJ I've never experienced any attempt to inspect the interior of the home, and only one definite inspection of the exterior for an announced reassessment of all properties and that was a drive by. About 9 years of that was living in an apartment, but still, uncommon. Every place I lived had either a finished attic, basement, or both. But they were also included in the habitable square footage on the taxes when we got there. 
    • 27.00 and change in tolls to drive down the shore from Rutherford,  47.00 in tolls to go out to Long island to visit dying relatives. Now I read they are going to raise the fees in the DMV. Murphy lied just to get elected when he said that seniors will get a significant tax break with his StayNJ" program to stop us from leaving.   Keep voting for democrats...this is what you get.  Tax and spend is all they know.  Never cut anything.  This state sucks.
    • I get the added benefit that since I have a TSP rather than a true 401(k) they tax my retirement too. Yaaaay!
    • PX4 Full Size 9mm Type G. Upgrades include: - Type G Stealth/Low Pro Levers and Slide Release - Truglo Tritium Pro Sights, White Outline Front Sight - Beretta Competition Trigger Group - LTT Optimized Trigger Bar - PX4 D Spring All parts professionally installed by gunsmith. Pistol has 400rds through it. All original parts (trigger group, trigger bar, Type F levers, sights) are included in sale. Original Beretta case and all contents included in sale. 3-10rd mags (these are the original mags that came with it). Pistol is in Excellent condition, there are a couple minor smudges on the lower part of the slide near the frame which I guess is from the sight vise. If I didn't point them out you wouldn't even notice. Trigger is super sweet, especially the SA Reset. Between the gun, parts, and gunsmith labor I have about $1200 into it. $800 Sale is Cash Only.   I'm in Whippany near Morristown. I will travel within a reasonable distance to meet at your preferred FFL to do the transfer. Buyer pays transfer fees.   -----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------      
×
×
  • Create New...