Jump to content
n4p226r

Pinning a b5 sopmod. Also sopmod vs imod

Recommended Posts

I have an LMT SOPMOD and a B5 Bravo on work guns, and 2 B5 Bravo stocks on personal guns. I prefer them over the VLTOR IMOD.

 

That being said, I wouldn't not put an IMOD on a gun - They are nice stocks.

 

As far as pinning, the Bravo is easily, drill through the stock into the receiver extension and pin.

 

The SOPMOD, I dont know. Looks like it would be difficult.

Share this post


Link to post
Share on other sites

I have drilled through the release pin mechanism, and pinned that with a roll pin. Doesn't mess up the stock visibly, nor does it drill into the RE.

It prevents the mechanism from working, effectively latching the stock in place.

Share this post


Link to post
Share on other sites

Did you drill behind the lever? Have any pictures? Did you remove the spring first?

I haven't taken the sopmod apart but I'm guessing it's similar to the m4 stock.

 

http://www.brownells.com/.aspx/pid=0/sid=809/schematicsdetail/AR_15_Sliding_Buttstock_Assembly?avad=avant&aid=41227&cm_mmc=affiliate-_-Itwine-_-Avantlink-_-Custom+Link

  • Like 1

Share this post


Link to post
Share on other sites

Oh, and FYI:

https://dsgarms.com/ktb5bravo-blk?utm_source=newsletter&utm_medium=email&utm_content=B5%20Milspec%20Bravo%20Buttstock%20Kit%20-%20Black&utm_campaign=5/6%20Retail%20-%20Armalite%20M15

Kit inlcudes a B5 BRAVO stock in black with milspec buffer tube, buffer spring, standard weight carbine buffer, lock ring and end plate.

B5 Bravo Stock kit for $75 (sign in for full discount).

Share this post


Link to post
Share on other sites

I figured I would update this in case people look in the future.

 

Remove the internal spring and drill and pin the location in this picture

 

A77F9C50-3FB5-499A-BEA7-C2AED31399CA_zps

 

100% invisible when you put the lever back on.

 

Drill bit is mc-master Carr part number 3146A113

 

 

Roll pin is mc-master Carr part number 92373A126

  • Like 1

Share this post


Link to post
Share on other sites

I figured I would update this in case people look in the future.

 

Remove the internal spring and drill and pin the location in this picture

 

A77F9C50-3FB5-499A-BEA7-C2AED31399CA_zps

 

Drill bit is mc-master Carr part number 3146A113

 

 

Roll pin is mc-master Carr part number 92373A126

Share this post


Link to post
Share on other sites
On 6/5/2016 at 2:26 PM, n4p226r said:

I figured I would update this in case people look in the future.

 

Remove the internal spring and drill and pin the location in this picture

 

A77F9C50-3FB5-499A-BEA7-C2AED31399CA_zps

 

100% invisible when you put the lever back on.

 

Drill bit is mc-master Carr part number 3146A113

 

 

Roll pin is mc-master Carr part number 92373A126

I’m new to a lot of this, and was wondering if you could help break down what you did to drill through the internal stock pin? With my current knowledge I’d most likely ruin the stock and drill around it, since it’s metal. I know this is years later but I have to give it a shot.

Share this post


Link to post
Share on other sites
On 4/25/2016 at 8:43 AM, Displaced Texan said:

I have drilled through the release pin mechanism, and pinned that with a roll pin. Doesn't mess up the stock visibly, nor does it drill into the RE.

It prevents the mechanism from working, effectively latching the stock in place.

Hello, I’m attempting to pin a SOPMOD myself and I’m having some trouble. Would you be able to share exactly how you would drill through the release pin mechanism? I know the plunger inside is round and if I attempted to drill through as is, I’m assuming the bit would slide off to the side before starting to bite into the pin. Not entirely sure how to end up with the results that the other gentleman had posted before. I know I’m 7 years late to the party but I was hoping you could help me. Thank you.

Share this post


Link to post
Share on other sites

It’s been a long time, and I since moved to Texas where I unpinned all that crap….

 

That being said, I think I used a small drill to make a hole at the spot I wanted. Made sure to dimple the plunger mechanism inside. 
Then, I removed the plunger, slowly drilled the rest of the way through it. 
Once I put everything back together I tapped a roll pin in.

 

I’m out of country on vacation at the moment, but when I get back, I can give you a visual of how I did it. 

Share this post


Link to post
Share on other sites
On 5/25/2023 at 12:43 AM, 050417Jl said:

Hello, I’m attempting to pin a SOPMOD myself and I’m having some trouble. Would you be able to share exactly how you would drill through the release pin mechanism? I know the plunger inside is round and if I attempted to drill through as is, I’m assuming the bit would slide off to the side before starting to bite into the pin. Not entirely sure how to end up with the results that the other gentleman had posted before. I know I’m 7 years late to the party but I was hoping you could help me. Thank you.

Hey, sorry I kind of forgot about this. 
 

My stock wasn’t a Sopmod, it’s a Vltor, but I imagine it will be similar. 
 

Here’s where I drilled on mine. I used a 4-40 set screw to prevent the latch from moving. You could use some JB Weld to putty over the screw, or for that matter, you could just leave it be. I believe as long as it’s not readily adjustable without using a tool, you’re gtg. 

60A16B0E-7B26-427C-B614-45477702881F.jpeg

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

  • Recently Browsing   0 members

    No registered users viewing this page.



  • olight.jpg

    Use Promo Code "NJGF10" for 10% Off Regular Items

  • Supporting Vendors

  • Latest Topics

  • Posts

    • I very seriously doubt this has anything to do with terrorism.    1) Harbor pilots are VERY seriously vetted, and highly trained. Not to mention extremely well paid. My experience knowing a few of them, and knowing how they are recruited and screened tells me that there is a slim to highly unlikely chance that a harbor pilot would have participated in anything like that.    2) Maintenance of foreign flag ships is well known to be dubious. Especially these days. These were NOT US flag, Jones act sailors. It was (to my understanding) a largely Indian crew on that ship, with a Ukrainian Captain. Indian crews are not exactly known for being stellar.    3) The bunkers (fuel) these ships use is ‘Bunker C’, which is a heavy, dirty fuel oil that can, and usually is, pretty contaminated. This stuff ain’t your car grade gasoline or diesel fuel. It’s nasty.   It requires nearly constant filter changes and maintenance to the engine/generators. The ship took on fuel prior to departing port, which would stir up all kinds of shit in the fuel tanks, which would contribute to particulates in the fuel lines/filters.    4) I’d say the posting of the chief engineer for Maserek above was pretty spot on as far as chain of events.    This was a shitty accident, with horrible timing and outcome. Not a terror attack. 
    • I saw Lara's interview on Bannon's War Room, and that gave me pause for thought. Her conjecture depends primarily on the veracity of her sources. Regardless, if it's not applicable in any way to this ship disaster, the methods described seem valid to me. And worthy of consideration for the future. As I said before, IMO something is coming. Death by a thousand cuts? Lara Logan Provides Comprehensive Baltimore Update: Experts in Behavioral Analytics, Counter-Terrorism, and National Security Analyze Recent Incident | The Gateway Pundit | by Jim Hᴏft
    • Another big windfall for governments'. The 'winner'? Not so much. Mega Millions $1.13 billion winner is facing mega tax bill. The amount is staggering. - nj.com
×
×
  • Create New...