Laser engraving in Monmouth Co.?

[DirtyDigz 1,812]

Anyplace do laser engraving in (ideally) Eastern Monmouth county?  Does not have to be an FFL (I want some graphics engraved on a slide that is currently raw metal).

If the same shop did cerakote too that would be a bonus.

[Persona non grata 113]

Sadly, I don't know anywhere in Monmouth County, but I use http://www.lasersourcellc.com/ at work all the time. They're in Warminster, PA. They don't do any coatings that I know of, just laser marking, etching and engraving.

[Scorpio64 5,154]

I recently use Perry's Trophy Shop in Long Branch (very 2A friendly) to engrave the magwel of a stripped AR lower.  You can call them and ask if they are able to do what you want or try another trophy shop.  Earth Treasures also does laser engraving but I cannot verify if they will engrave firearms components.

[bhunted 887]

Just remember. If its serialized , they have to hold an ffl.



Sent from my iPhone using Tapatalk

[Scorpio64 5,154]

7 minutes ago, bhunted said:

Just remember. If its serialized , they have to hold an ffl.



Sent from my iPhone using Tapatalk

Only if you are going to leave it there.  If you remain on premises and they do it while you wait there is no transfer.  Engraving is not gunsmithing so the engraver does not need a FFL.

[DirtyDigz 1,812]

Hold on there bhunted - I only thought the FFL requirement was for actual *firearms* (frames/lowers).  A slide with a serial # on it (and just the slide) requires an FFL to work on?  Since when?

(The slide I want to get engraved is not serialized)

[bhunted 887]

Hold on there bhunted - I only thought the FFL requirement was for actual *firearms* (frames/lowers).  A slide with a serial # on it (and just the slide) requires an FFL to work on?  Since when?

(The slide I want to get engraved is not serialized)

Then no prob.

As Scorp says, that also holds true for cerakoting.

I mentioned this because most places never do things while you wait these days.

Look at it this way. All guns are illegal in commie jersey right?
Only transportable between ranges, repairs, manufacturers, etc.



Sent from my iPad using Tapatalk

[1LtCAP 4,263]

2 hours ago, bhunted said:

Just remember. If its serialized , they have to hold an ffl.



Sent from my iPhone using Tapatalk

even just for something like he's asking for?

not trying to be a wise guy......

[DirtyDigz 1,812]

1 hour ago, 1LtCAP said:

even just for something like he's asking for?

not trying to be a wise guy......

Yeah, I think you're missing the question bhunted.  Let me try this again - hypothetical:

I have a glock 19.  It has a serialized frame, slide and barrel.

I remove the slide from the frame, and the barrel from the slide.  I leave the frame and barrel at home.  I take the (serialized) slide with me in my pocket to drop off at a shop to get engraved and picked up several days later.

Are you saying that even though the slide is not a firearm (it's just a part), because it's serialized the shop has to have an FFL in order for me to leave it there to be worked on?

If so, I find that hard to believe.
 

[Scorpio64 5,154]

Can you buy a new slide and have it shipped directly to your house or does a slide have to go through an FFL?  It is my understanding that only handgun frames have to go through an FFL.

[bhunted 887]

Can you buy a new slide and have it shipped directly to your house or does a slide have to go through an FFL?  It is my understanding that only handgun frames have to go through an FFL.

 

Handgun frames just like AR lowers.

I thought he said frame. My bad.

Like lowers, it has to be an ffl.

 

Not sure it matters for just the slide.

 

I’m sure the FFLs here can chime in.

 

 

 

 

Sent from my iPhone using Tapatalk

[bhunted 887]

Hold on there bhunted - I only thought the FFL requirement was for actual *firearms* (frames/lowers).  A slide with a serial # on it (and just the slide) requires an FFL to work on?  Since when?

(The slide I want to get engraved is not serialized)

My bad. But also, Scorps friend shouldn’t have left it.


Sent from my iPhone using Tapatalk

[bhunted 887]

Let me clarify. Too much confusion. I was referring to Scorps friend scenario combined with Dougs...[emoji16]

I’ll just say:

You cannot leave any lower/frame at any non-ffl....

 

FFLs, correct me if I’m wrong.

Sent from my iPhone using Tapatalk

 

[1LtCAP 4,263]

CONFUSION IS WHERE WE LIVE.

[DirtyDigz 1,812]

Ok, all good.

(That said, way back when I got my first glock pistol, I took the slide (*only*) to the Bullet Hole to have them install night sights on it.  They insisted on logging the slide into their bound book.  I questioned that, since it wasn't a firearm, but they were not tolerating any discussion on the matter.)

[Pew Pew Plates 358]

Just because something has a serial number doesn't mean you need an FFL...just the frame is the firearm by definition

If you dropped your computer keyboard off at the engraver, does he need an FFL because it has a serial number?

[PK90 3,570]

Not all frames have serial numbers, and not all serial numbers are firearms. LOL

[bhunted 887]

Just because something has a serial number doesn't mean you need an FFL...just the frame is the firearm by definition
If you dropped your computer keyboard off at the engraver, does he need an FFL because it has a serial number?

We did say that so what is your point? [emoji848][emoji23]


Sent from my iPad using Tapatalk