-
Recently Browsing 0 members
No registered users viewing this page.
-
Supporting Vendors
-
-
Latest Topics
-
-
Similar Content
-
By RetNJ47
Great start for people looking to get into reloading. $500. (FIRM)
RCBS Rock Chucker Supreme IV Single Stage Press on Inline Fab stand with extras. Located in the Lakewood area(Weshoot or Shoreshot). Would prefer to meet at either of those spots but willing to meet halfway.
Rockchucker Supreme IV Single Stage Press
https://www.rcbs.com/presses/single-stage/rock-chucker-supreme-press/16-9356.html
Inline Fabrication Ultramount for RCBS Rockchucker, RC1,2,3. Supreme IV,Pro2000 & Turret presses.
https://inlinefabrication.com/collections/rcbs/products/ultramount-for-rcbs-rockchucker-rc1-rc2-supreme-pro2000
Inline Fab Automatic Case Ejector System
https://inlinefabrication.com/collections/rcbs/products/case-ejector-system-for-rcbs-rockchucker-single-stage
Inline Fab Universal double component tray system.
https://inlinefabrication.com/collections/press-accessories/products/universal-double-bullet-tray-system?variant=323708361
RCBS
Uniflow Powder Drop
https://www.rcbs.com/priming-and-powder-charging/mechanical/mechanical/uniflow-powder-measure-iii/16-9016.html
M500 Mechanical Scale
https://www.rcbs.com/priming-and-powder-charging/weighing-scales/m500-mechanical-scale/16-98915.html
Powder Trickler
https://www.rcbs.com/priming-and-powder-charging/scale-and-powder-accessories/powder-trickler-2/16-9089.html
Universal Case Loading Block
https://www.rcbs.com/case-processing/accessories/universal-case-loading-block/16-9452.html
Hand Priming Tool for Small and Large Primers
https://www.rcbs.com/priming-and-powder-charging/hand-held/hand-priming-tool/16-90200.html
Additional press add ons:
(NIB) Advanced Powder Stand
https://www.rcbs.com/priming-and-powder-charging/scale-and-powder-accessories/advanced-powder-measure-stand/16-9092.html
(NIB) RCBS Auto Prime System
https://www.rcbs.com/presses/press-accessories/rock-chucker-supreme-auto-prime/16-9358.html
Hornady impact bullet puller.
Small items include (2) funnels with different attachments, calipers, primer pocket brush, case lube, case wax, case lube pad, lube pad roller, and die wrench.
All the heavy lifting to start reloading is done. This press/die set has only been used to deprime a few cartridges(I have no patience). Aside from dust it’s brand new.
****DISCLAIMER**** Not my fault if you do something stupid and get hurt. Do your research.
-
By RetNJ47
Selling my Troy A4 “Other” Firearm 5.56(.223) with Blast Shield (faux suppressor) and BA Hanson profile 11.3” precision barrel with Silencer Co ASR muzzle brake.
Had gunsmith remove pin and welded muzzle brake on stock 10.5” inch barrel. Upgraded to BA 11.3” performance barrel bringing OAL to 26.8 inches without pin and welded muzzle device. ASR threaded Silco brake added with 6” Blast Shield. Trigger/Feed Ramp polish job for smoother take up and crisp reset(for a Mil-Spec trigger). Only 40 rounds have been fired for testing and proper initial barrel break in using Modern Spartan Systems accuracy oil between shot cycles.
Full list of modifications:
-Ballistic Advantage Hanson Profile 5.56 chambered 11.3 inch Performance Series Barrel
-SilencerCo Muzzle Brake
-SDTA 6” Blast Shield
-SBA3 Brace (Black or possibly FDE available)
-Magpul Gen 2 BUIS and Vertical Foregrip
-CMMG Stainless Gas Tube
$1550
Located in Toms River with closest FFL being Weshoot/Shoreshot. Buyer responsible for transfer fee at FFL.
Still have stock barrel also if interested.
**Eotech Not Included** if interested it’s an EOtech EXPS2-0 and I have a G43 magnifier w/STS mount and Surefire light with pressure pad to go along with it.
-
By 8lbsledge
Looking to sell 1940 dated, Sniper marked Tula Mosin-Nagant with 40rd of Yugoslav Surplus LPS ammo with 2 clips. Rifle began it's life from the factory as a PEM pattern sniper rifle, sporting a copy of a German ZF-39 scope on a side mount. After the war, it was decommissioned and placed in a laminate stock, with the optic removed. Despite the stock replacement, the buttplate was retained from the original stock, and is numbered 217 like the rest of the parts. Rifle functions, and shoots fairly well, and the bore is in good shape. Photos provide proof of previous optic mount.
Included: Rifle, 40rd surplus ammo, 2 clips
Price for all pictured: $550 cash
Located in Warren county, will not drive further than 45min from washington
-
By Mr.Stu
I have been asked to run a class to prepare people for carrying a defensive firearm by my home range, Phillipsburg Pistol club.
It will be held on August 6th, from noon until approx. 4pm.
We will cover safe use of a holster and a number of defensive shooting techniques.
The class will finish with running each student through HQC1 and a certificate will be provided for those that achieve a passing score.
It is open to all, but members of Phillipsburg Pistol Club will have spots reserved for them.
Sign up here: https://www.eventbrite.com/e/holster-use-and-defensive-shooting-techniques-registration-675278625547
-
-
Posts
-
Looking to buy some non-corrosive 7.62x39. I'm located in Bergen County. Please let me know if you have some at a decent price.
-
ff to approx 1:20. sped up this looks like a controlled turn. hopefully it wasn't.......
-
watch this video. there were at least 4 stationary construction vehicles.
-