Recently Browsing 0 members
No registered users viewing this page.
For sale awesome MEC 9000HN Hydraulic reloading press $600 ! I already have a pair of these machines and tuned this up perfectly. It has been stripped down, cleaned, assembled, lubed and run 200 shells. They chambered and shot perfect. This machine needs nothing to start loading shells at a rate of 300 per hour. If you have a single stage or manual progressive MEC, this is the machine for you. Your arm will thank you, the hydraulic 110VAC pump has a foot pedal. It draws less than 10 amp, can plug in anywhere. The sizing collet is in perfect condition.
It is set up now for 1-1/8 oz 1,200 FPS velocity using Cheddite 209 primers, WIN wad & Remington Gun club hulls. These are great hulls to reload, the plastic is perfect for re-crimping. I can set it up for another load or show you how to do it.
This machine lists for $1,211 at Midway + shipping but you can get a machine fully set up and working for the low price of $600 ! This will produce $9 per box Winchester AA loads for about $5. Plus the machine will always have resale value, parts and service are available from MEC. I have been loading on the 9000 for 5 years and they are easy to adjust & maintain.
Act now and included in the price is the MEC maintenance tools for adjusting base re-sizing & main spring removal ($32 value), MEC Bushing rack ($30 value), 9 bushings ($45 value) 3 charge bars ($54 value). That is over $150 worth of extra stuff that you don't have to buy! The manual is included. Man that's a lot of extra stuff.
The extra bushings will allow you to make any 7/8 oz, 1 oz, 1-1/8 oz shell at any velocity. You can make some low recoil now noise light loads for the kids up to a killer 75 yard sporting clay crusher for the end station at Lehigh.
OK, this sounds too good to be true but I want to sell it to a forum bud and skip the hassle of shipping it on EBay. The machine is under power and will produce shells immediately. I couldn't sell it any other way. Pickup only in Brick NJ.
This is not me but it is a very accurate representation of the machine. Best to call or text 732-691-8706, I don't check Forum replies too often.
Amazon currently has the Hornady brass tumbler listed for $27.99, shipped and sold by Amazon. Cheapest price around for this tumbler.
Edit: See next post, just realized there is also free 100 bullets from Hornady, just pay shipping. Link to rebate!
Some sold, some left, some changes. By request, asking prices for individual die sets now listed.
I dropped shooting many calibers, so I am thinning out my reloading gear and components.
Can meet in the Morristown/Randolph/Mendham area for any sale over $25. Will ship Priority Mail at cost if prepaid with postal money order.
The only item I might consider in trade is an automatic (12v electric) trap thrower.
see pics at end
Components: ALL SOLD
All remaining sets (1,2,3,5,6) for $120 OBO.
If they don't sell as a bundle then I may divide the sets up and go the Ebay route. I initially priced the sets 25-50 each, depending (total $235). But instead, I've decided to offer the bundle at a large discount to save the time and trouble of multiple small sales, shipping etc. (basically buying 3 sets and the rest are gratus).
All dies are rust free, have scratch free interiors and produce perfect ammo. Some of the decapping pins should be replaced.
set #1: $40
9mm RCBS carbide sizer, CH speed seater (really nice die), CH taper crimp, machinist made powder check die, 9mm loaded cartridge gauge
set #2: $25
9mm Pacific Durachrome carbide sizer, Lee seater, Lee Factory Crimp Die
set #3: $40
.357 mag Lyman carbide sizer, Lee seater, Lee Factory Crimp Die, machinist made powder check die, .357 mag loaded cartridge gauge
set #4: $40 SOLD
.38 sp Lyman carbide sizer, Lee seater, Lee Factory Crimp Die, machinist made powder check die, .38 sp loaded cartridge gauge
(the top of the sizing die was milled by 3mm, does not affect function) Yes, I realize .38 and .357 typically use the same dies but it is useful to have 2 sets so you can leave them setup/adjusted for each caliber.
set #5: $25
.45 acp Lyman carbide sizer, Lee seater, Lee Factory Crimp Die with extra seater insert to customize to your bullet shape
set #6: $25
9mm Redding carbide sizer
.45-70 RCBS sizer (no decapping stem)
.380 acp RCBS carbide sizer (no decapping stem)
.38 sp RCBS seat/crimp (no stem) SOLD
Misc. Reloading Equipment:
Dillon AT 500 powder die - $18 $15 https://www.dillonprecision.com/at-500-powder-die_8_4_23631.html
Dillon standard powder die (New) - $13 $10 https://www.dillonprecision.com/dillon-powder-die_8_4_23603.html
loaded cartridge counter - $25 $20
It's a shame. I was hoping due to the gap in weather they would go for it, but considering lightning can travel 25 miles from where it originates, plus the shift in weather over 20 minutes was going to make it too tight. Did they say when it's rescheduled to?
I had a perf center shield that’s now kind of sitting the box, I’ve sworn off selling stuff, because of my 365. I have more than 2000 rounds through it and my trigger is very smooth when compared to when I first started shooting it. I find the accuracy to be very similar to the shield but find handling the gun amazingly comfortable. I have fairly average sized hands. I also like the sites (night sites) on the sit much better. I am not sure now your finger is coming off the trigger and getting caught between the bottom of the bow and the guard. You should probably try and get a pick of that. I’m not sure how a flat blade would help, I’m guessing same clearance from tip to guard. last bit. I felt the Sig fires SD ammo better than the shield. A bit more controllable and thus a bit more accurate with those snappier rounds.
I like my RIA models, but pay attention to the sights on some of their model lines. The old GI-style sights I find very difficult to use at the range. Still shoot great though, just harder to hit what I want with my old eyes. Hard to beat a $400 1911 though.