Jump to content
Malsua

30HP Screw type Compressor & Automatic brass buffing machine

By Malsua, in NJGF-List

Recommended Posts

Malsua    1,422

Malsua
Posted

 

So I have two items that I'm trying to get rid of.

One is a Sullair ES-8.  This is a 3 phase screw type air compressor.  This provides 95CFM at 140PSI.  It makes a lot of air!  Used, not sure on hours.  Can test run it before a sale.  It's a serious compressor.  Loud too.

 

The other is a Mutschler Edge Technologies Universal indexing dual spindle buff machine.  Never been used.  The plan was for it to polish brass but we ended up pulling out of the country right as this got delivered.  It never ran in production.   It polished brass tubes, or rifle brass, etc.

These are both pallet sized pieces of equipment, both are industrial usage or like a gas station, etc.

The Compressor goes for about 6k used.   We could probably do half that.

The other machine...I'd have to show someone, it's real hard to explain.  You put your brass on this chuck, it goes in, buffs and you load the other side.  Then that goes in, you take out the first two, rinse, repeat.  It's set up for automation.

 

 

 

 

 

 

Share this post

Link to post
Share on other sites

Malsua    1,422

Malsua
Posted
Just now, capt14k said:

Would this compressor work for running autoshop lifts and airtools, or is it an overkill.

You can run 3/4" impacts with it.   I'm sure if you had a holding tank, you could run pretty much anything..  You'd have to look at the requirements of a lift, I think they are more about PSI than CFM though.   It's right sized for a small to medium auto shop.

It might be a bit small for a jack hammer, but you'd use a portable gas powered for that anyway.

 

 

 

 

 

Share this post

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
Go To Topic Listing

  • Recently Browsing   0 members

    No registered users viewing this page.



  • NJGF/SlavGuns Gun Giveaway!

    Ruger65Grendel.jpg

     

  • olight.jpg

    Use Promo Code "NJGF10" for 10% Off Regular Items

  • Supporting Vendors

  • Latest Topics

  • Posts

    • silverado427
      Daily humor thread

      By silverado427 · Posted

    • raz-0
      The Tax Man Commeth

      By raz-0 · Posted

      In 50 years of living in NJ I've never experienced any attempt to inspect the interior of the home, and only one definite inspection of the exterior for an announced reassessment of all properties and that was a drive by. About 9 years of that was living in an apartment, but still, uncommon. Every place I lived had either a finished attic, basement, or both. But they were also included in the habitable square footage on the taxes when we got there. 
    • Tunaman
      The Tax Man Commeth

      By Tunaman · Posted

      27.00 and change in tolls to drive down the shore from Rutherford,  47.00 in tolls to go out to Long island to visit dying relatives. Now I read they are going to raise the fees in the DMV. Murphy lied just to get elected when he said that seniors will get a significant tax break with his StayNJ" program to stop us from leaving.   Keep voting for democrats...this is what you get.  Tax and spend is all they know.  Never cut anything.  This state sucks.
    • Shocker
      Wondering Where Your NJ Lifetime Income Went?

      By Shocker · Posted

      I get the added benefit that since I have a TSP rather than a true 401(k) they tax my retirement too. Yaaaay!
    • diamondd817
      WTS: Beretta PX4 FS 9mm Lots of Upgrades

      By diamondd817 · Posted

      PX4 Full Size 9mm Type G. Upgrades include: - Type G Stealth/Low Pro Levers and Slide Release - Truglo Tritium Pro Sights, White Outline Front Sight - Beretta Competition Trigger Group - LTT Optimized Trigger Bar - PX4 D Spring All parts professionally installed by gunsmith. Pistol has 400rds through it. All original parts (trigger group, trigger bar, Type F levers, sights) are included in sale. Original Beretta case and all contents included in sale. 3-10rd mags (these are the original mags that came with it). Pistol is in Excellent condition, there are a couple minor smudges on the lower part of the slide near the frame which I guess is from the sight vise. If I didn't point them out you wouldn't even notice. Trigger is super sweet, especially the SA Reset. Between the gun, parts, and gunsmith labor I have about $1200 into it. $800 Sale is Cash Only.   I'm in Whippany near Morristown. I will travel within a reasonable distance to meet at your preferred FFL to do the transfer. Buyer pays transfer fees.   -----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------      
×
×
  • Create New...