Full Round Stuck in Barrel

[Greenday 323]

Strange thing happened to me this morning at Range 14. Was shooting some .223 out of my Ruger Ranch in 5.56 and with one of my rounds, there was no recoil and no new hole in my target. Took my magazine out, opened the chamber and there was a full round, case and bullet, stuck in the barrel with the primer end flush meeting the chamber. I've never seen or heard of this before. What would cause this?

[PK90 3,570]

Wrong caliber cartridge?

[Greenday 323]

3 minutes ago, PK90 said:

Wrong caliber cartridge?

Nope, it was a once fired .223 round.

[carl_g 568]

You probably screwed up reloading the round. Did you run it thru a case gauge?

[silverado427 10,716]

Them liberal tear drops of your's  probably rusted up the chamber.

[Greenday 323]

3 minutes ago, carl_g said:

You probably screwed up reloading the round. Did you run it thru a case gauge?

That's what I figured, but it was the correct length, diameter, etc.And I weighed out every single charge. It's almost like when it loaded from the magazine into the chamber, it immediately slid into the barrel. Just glad I didn't try to fire another round.

5 minutes ago, silverado427 said:

Them liberal tear drops of your's  probably rusted up the chamber.

I thought that too!

[ChrisJM981 924]

Did you crimp the rounds?

[JackDaWack 2,895]

48 minutes ago, Greenday said:

That's what I figured, but it was the correct length, diameter, etc.And I weighed out every single charge. It's almost like when it loaded from the magazine into the chamber, it immediately slid into the barrel. Just glad I didn't try to fire another round.

I thought that too!

But..... did you use a case gauge?

Was the primer struck?

 

Im going to take a guess here and say you over sized the round... it's literally the only way a cartridge can push past the neck in the chamber... and if it was measured with out a case gauge then OAL would jam the bullet into the lands

18 minutes ago, ChrisJM981 said:

Did you crimp the rounds?

I cant imagine how that would effect the chambering of the round... 

[Zeke 5,504]

No powder?

[silverado427 10,716]

1 hour ago, Greenday said:

That's what I figured, but it was the correct length, diameter, etc.And I weighed out every single charge. It's almost like when it loaded from the magazine into the chamber, it immediately slid into the barrel. Just glad I didn't try to fire another round.

I thought that too!

Glad you didn't have a Kaboom.

[Sota 1,191]

It's Greenday.  Why the hell are you even replying.

[Greenday 323]

58 minutes ago, JackDaWack said:

But..... did you use a case gauge?

Was the primer struck?

Im going to take a guess here and say you over sized the round... it's literally the only way a cartridge can push past the neck in the chamber... and if it was measured with out a case gauge then OAL would jam the bullet into the lands

Yes. Case gauge, pocket gauge, calipers. Length of everything was 2.2580 plus/minus 0.0005" I was kinda anal about making them all the same dimensions for consistency. Not sure if the primer was struck. Sounded like a dry fire to me. It's completely possible of course I missed one sizing them.

1 hour ago, ChrisJM981 said:

Did you crimp the rounds?

No.

41 minutes ago, Zeke said:

No powder?

Would that make the case go into the barrel? I know that can cause a squib round.

[Zeke 5,504]

He has a point lol

[Zeke 5,504]

1 minute ago, Greenday said:

 

Would that make the case go into the barrel? I know that can cause a squib round.

I skim read. The problem here is the idiot reloading is not using a case gauge. . I’d smartin up and pay attention to what you are doing before you get yourself or someone else hurt. 

[Greenday 323]

1 hour ago, Zeke said:

I skim read. The problem here is the idiot reloading is not using a case gauge. . I’d smartin up and pay attention to what you are doing before you get yourself or someone else hurt. 

I said I used a case gauge.

[njJoniGuy 2,131]

Please post a picture of your case gauge. There are many.

[Greenday 323]

15 minutes ago, njJoniGuy said:

Please post a picture of your case gauge. There are many.

It's a Hornady Lock-N-Load cartridge gauge for 223 rem.

[voyager9 3,434]

Found the problem 

[Greenday 323]

I just want my guns to endlessly fire bullets without ever pausing to reload and for my cars to have as many gears as the ones in the Fast and the Furious movies where they never downshift, just upshift like 20 times.

[JackDaWack 2,895]

7 hours ago, Greenday said:

Yes. Case gauge, pocket gauge, calipers. Length of everything was 2.2580 plus/minus 0.0005" I was kinda anal about making them all the same dimensions for consistency. Not sure if the primer was struck. Sounded like a dry fire to me. It's completely possible of course I missed one sizing them.

No.

Would that make the case go into the barrel? I know that can cause a squib round.

Highly unlikely that you missed one, you have to push the neck WAY back to get the case physically stuck like that. They would all be miserably out of spec if that were the situation. 

Do you still have the case?

If it was a squib.... the bullet may have just stuck itself in the throat of the chamber, there is no standard for how far the bullet will travel down the barrel with no powder...

[silverado427 10,716]

So did you get the round out of the barrel. ?

[Greenday 323]

1 hour ago, silverado427 said:

So did you get the round out of the barrel. ?

We got it out at the range. Used a cleaning rod.

[carl_g 568]

This thread is useless and sucks. If you want help you need to provide more info and pictures. I still say you screwed up reloading the round. Be careful 

[Zeke 5,504]

23 minutes ago, carl_g said:

This thread is useless and sucks. If you want help you need to provide more info and pictures. I still say you screwed up reloading the round. Be careful 

I think @Sotagave the best advice.

[PK90 3,570]

I betcha he threw it over the wall.

[JC_68Westy 1,024]

29 minutes ago, PK90 said:

I betcha he threw it over the wall.

In a very safe manner...

[Zeke 5,504]

Just now, JC_68Westy said:

In a very safe manner...

Repeatedly 

[JC_68Westy 1,024]

Just now, Zeke said:

Repeatedly 

But always in a safe manner.

[Zeke 5,504]

@PK90 @JC_68Westy

 

lmfao

[Greenday 323]

1 hour ago, PK90 said:

I betcha he threw it over the wall.

Some dumbasses were tossing rounds onto the concrete to see if they could set them off.