NJSigfan 218 Posted August 22, 2019 Hello fellow reloaders, I need some help solving a reloading problem. Let me start by saying I’ve been reloading 45 ACP and 9mm for a few years now and until today everything has gone smoothly and bang at the range. Historically I’ve reloaded using FMJ delta precision or plated extreme bullets, my own once fired brass, CCI primers and few different powders. I use a Lee 5 stage progressive press with Lee carbide 4 die set with a universal decapping die. Today, I had an afternoon free so I decided to decompress by reloading some 9mm. Only this time, I used 115gr coated bullets from ibejiheads that I picked up about 6 months ago. So I started reloading, finished 5 rounds then stopped to QC them. Here is where my confusion and frustration comes in. I had the OAL set at 1.150 with a decent crimp. When I went to gauge check them, they were too long. I had to reduce the OAL to 1.103 which is below the minimum OAL of 1.125 that’s recommended for titegroup powder. Could the coating throw off the OAL length that much? I did the plunk test on my p226 barrel and it “plunks” nicely. I ended up taking all the dies out of the press and reset them, but no matter what I do I can not get the rounds to fit flush in the gauge checker. The heads measure 0.3125 wide and .05395 tall, primers sit flush in resized federal brass. The brass even sits flush in the gauge checker until I load the heads. My question is; can I safely fire these rounds if they measure below 1.125 OAL? What would cause them to plunk nicely but not sit flush in the gauge checker? Quote Share this post Link to post Share on other sites
Maksim 1,504 Posted August 22, 2019 Depending on the dies and the bullet head profile. Should be safe to fire if you loaded light... Would not risk if you are using a fast powder and a hotter load. What guns are you shooting it from? I generally load slightly long anyway. Only picky ones are stock cz barrels and some glocks. But this is also why i chamber check every round for match ammo. Not a block but my actual gun barrel. Quote Share this post Link to post Share on other sites
Longranger 16 Posted August 22, 2019 Do you have load data for the ibjiheads bullets and titegroup? It's generally not a good idea to just change bullets and expect the same recipe to apply. Sounds like the coated bullets have a much more round profile than the FMJs. -Longranger Quote Share this post Link to post Share on other sites
NJSigfan 218 Posted August 22, 2019 @Maksim I loaded to 4.0 grains of titegroup. Max load for 115gr lead calls for 4.3 grains of titegroup. I tend to load lite or midrange to the published max load to keep things safe. These were just plinking round so I can shoot them from my browning or P226. @Longranger I’m not aware of any specific load date for ibejiheads but was told to follow for equivalent weight lead. Quote Share this post Link to post Share on other sites
Maksim 1,504 Posted August 22, 2019 Ibej heads are simply moly coated lead. So you can push them a bit more than lead but keep around plated or lower. They are good bullets popular with the Pinoys and local USPSA shooters. Goos people. Quote Share this post Link to post Share on other sites
Mr.Stu 1,916 Posted August 22, 2019 What weight bullet do you usually use? If you are used to 124gr or 147gr you will find the ogive to be quite different. If the seating surface of the die has a hollow center and it touching the head somewhere below the tip you will find the lighter head will sit higher than the fatter, heavier head. Quote Share this post Link to post Share on other sites
Longranger 16 Posted August 22, 2019 Hodgdon website says COL for the 115gr LRN loaded with Titegroup is 1.100. You're pretty much right there at 1.103. -Longranger Quote Share this post Link to post Share on other sites
NJSigfan 218 Posted August 22, 2019 For christ sake, @Longranger you’re right. I was just looking at their site and saw the minimum value. The question now is, how did I mix mix it up with 1.125? I’ll leave that for tomorrow tho. thanks to @Maksimand @Mr.Stu for their help as well.q Quote Share this post Link to post Share on other sites
Bagarocks 36 Posted August 25, 2019 Its funny how ya pay attention to detail and get everything right and then ya say "wait a sec" what just happened? I think we have all been there at one point or another Quote Share this post Link to post Share on other sites
tony357 386 Posted August 28, 2019 Just adjust the seating die to your desired height. Quote Share this post Link to post Share on other sites
ronhonda 86 Posted August 28, 2019 17 hours ago, tony357 said: Just adjust the seating die to your desired height. this. measure the head and compare it to the plated stuff you use. will need to readjust dies with new heads. Quote Share this post Link to post Share on other sites