Jump to content
kc17

SIG M18

Recommended Posts

5 hours ago, Zeke said:

I’m still not sure if a chamfer bit or step bit would be better.

Step 1:  remove magazine spring and follower.

Step 2:  drill a pilot hole through both divets.  Use a small pilot bit.

Step 3:  drill another hole using a bigger bit making sure you go straight through both holes.

Step 4:  repeat step 3 on the other side of the magazine body.  

Step 5:  reinstall magazine spring and follower and function check with ammunition. 

Step 6:  no step on snek

Share this post


Link to post
Share on other sites
44 minutes ago, Ray Ray said:

Step 1:  remove magazine spring and follower.

Step 2:  drill a pilot hole through both divets.  Use a small pilot bit.

Step 3:  drill another hole using a bigger bit making sure you go straight through both holes.

Step 4:  repeat step 3 on the other side of the magazine body.  

Step 5:  reinstall magazine spring and follower and function check with ammunition. 

Step 6:  no step on snek

You can’t remove the follower... pre

Share this post


Link to post
Share on other sites
7 hours ago, bhunted said:

Paper towels and Windex....let air dry.:rolleyes::icon_lol:

I'm not saying that you MUST clean your magazines all the time but one drop in Range 14 sand and they are crusty. 

Share this post


Link to post
Share on other sites
13 hours ago, Ray Ray said:

I'm not saying that you MUST clean your magazines all the time but one drop in Range 14 sand and they are crusty. 

:nea:You didn't get it. lol.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

  • Recently Browsing   0 members

    No registered users viewing this page.



  • olight.jpg

    Use Promo Code "NJGF10" for 10% Off Regular Items

  • Supporting Vendors

  • Latest Topics

  • Posts

    • In 50 years of living in NJ I've never experienced any attempt to inspect the interior of the home, and only one definite inspection of the exterior for an announced reassessment of all properties and that was a drive by. About 9 years of that was living in an apartment, but still, uncommon. Every place I lived had either a finished attic, basement, or both. But they were also included in the habitable square footage on the taxes when we got there. 
    • 27.00 and change in tolls to drive down the shore from Rutherford,  47.00 in tolls to go out to Long island to visit dying relatives. Now I read they are going to raise the fees in the DMV. Murphy lied just to get elected when he said that seniors will get a significant tax break with his StayNJ" program to stop us from leaving.   Keep voting for democrats...this is what you get.  Tax and spend is all they know.  Never cut anything.  This state sucks.
    • I get the added benefit that since I have a TSP rather than a true 401(k) they tax my retirement too. Yaaaay!
    • PX4 Full Size 9mm Type G. Upgrades include: - Type G Stealth/Low Pro Levers and Slide Release - Truglo Tritium Pro Sights, White Outline Front Sight - Beretta Competition Trigger Group - LTT Optimized Trigger Bar - PX4 D Spring All parts professionally installed by gunsmith. Pistol has 400rds through it. All original parts (trigger group, trigger bar, Type F levers, sights) are included in sale. Original Beretta case and all contents included in sale. 3-10rd mags (these are the original mags that came with it). Pistol is in Excellent condition, there are a couple minor smudges on the lower part of the slide near the frame which I guess is from the sight vise. If I didn't point them out you wouldn't even notice. Trigger is super sweet, especially the SA Reset. Between the gun, parts, and gunsmith labor I have about $1200 into it. $800 Sale is Cash Only.   I'm in Whippany near Morristown. I will travel within a reasonable distance to meet at your preferred FFL to do the transfer. Buyer pays transfer fees.   -----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------      
×
×
  • Create New...