I really mean this nicely, but:
As a new reloader, save yourself a lot of problems and LEARN first.
Buy some JACKETED, not plated, bullets from a major maker.
Buy a powder that has been around for at least 10 years and is well known for working in the cartridge you want to load. You can look at several manuals and most will tell you what powders worked best for them. I am not sure how long CFE Pistol has been around, but I don't have much data for it. I expect it is very good for 9x19.
After a few hundred rounds of success, you can then move to plated or lead bullets and start trying different powders.
Instead, you start off with plated bullets (that have almost no data available and need special handling) and what is, to me, a relatively new powder so there is very little data to go on.
So, your first time out learning to drive, do you take a Mercedes F1 W08 EQ Power+ or a Corolla to learn how to drive?
Do you take a Yamaha SCR 950 or a Suzuki DR 200 motorcycle for your first lesson?
Hey, I load 9mm. 9x19, 9x21, 9x23, 9x18, and 9x17. Which one of the almost 50 different 9mm cartridges are you loading for?
Oh, of course, 9x19...
>The difference in the start grain loads is due to the different OAL's, is that correct?
NO. All the start load is usually is a 10% reduction in the max load. The max load is determined by the components used and, when comparing your data, I'll bet NONE of the components were the same. COL is NOT the driver of start loads, other than the start load is safe for any normal COL used. The manual's COL may be no more than a short COL they used for testing, to be a worst case, and you should use a longer COL. Learn to determine the COL for yourself.
The sheer fact that they note it as a "MIN COL" tells you not to go shorter. In reality, first work out in your gun what COL works and then start loading. If shorter, you might want to reduce the start load by 2-5%, but I have never found that necessary—but, then again, I always check multiple sources and start at the LOWEST start load.
1) Bullets of the same weight vary in dimensions. The COL in a manual, if it really means anything, only applies to THAT bullet. The dimensions of the bullet determine the max COL before the bullet ogive or shoulder hits the lede.
Your COL (Cartridge Overall Length) is determined by;
your barrel (chamber and throat dimensions)
and
your gun (feed ramp)
and
your magazine (COL that fits magazine and when the magazine lips release the round for feeding)
and
the PARTICULAR bullet you are using.
What worked in a pressure barrel or the lab's gun or in my gun has very little to do with what will work best in your gun.
Take the barrel out of the gun. Create two inert dummy rounds (no powder or primer) at max COL and remove enough case mouth flare for rounds to chamber (you can achieve this by using a sized case—expand-and-flare it, and remove the flare just until the case "plunks" in the barrel and lock the die body down temporarily).
Drop the inert rounds in and decrease the COL until they chamber completely. This will be your "max" effective COL. I prefer to have the case head flush with the barrel hood (or a few mils higher than where the head of an empty case aligns with the barrel, as all cases are too short and I prefer to minimize head space). After this, place the inert rounds in the magazine and be sure they fit the magazine and feed and chamber. Adjust COL until the inert rounds feed and chamber. Note any set-back and note the COL or redo the dummy rounds if need be.
You can also do this for any chambering problems you have. Remove the barrel and drop rounds in until you find one that won't chamber. Take that round and "paint" the bullet and case black with Magic Marker or other marker. Drop this round in the barrel and rotate it back-and-forth.
Remove and inspect the round:
a) Scratches on bullet--COL is too long
b) Scratches on edge of the case mouth--insufficient crimp
c) Scratches just below the case mouth--too much crimp, you're crushing the case
d) Scratches on case at base of bullet--bullet seated crooked due to insufficient case expansion (not case mouth flare) or improper seating stem fit
e) Scratches on case just above extractor groove--case bulge not removed during sizing. May need a bulge buster.
2) Loading data: If you look at two manuals, you'll see very different start and max loads. This should tell you that:
a) NO manual is perfect
and
b) COMPONENTS have an effect. Unless you have the same LOT of powder, the same LOT and manufacturer of primers, the same cases, the same LOT and manufacturer of bullets, the same COL, and, of course, the same GUN, your results will vary. You can "always" use the start load for any bullet of the same weight and construction. For plated bullets, back when I thought they might be worth using, I always used lead bullet data and never had a problem (other than horrible accuracy)
For this reason, and the fact that twice in my life I found the start load in a manual to be max or over-max with my components, I check multiple sources and start at the lowest start load. I never guess, estimate, or anything else. I start at the lowest start load and work up.
So, I would start at 4.4gn and work up (with MAX probably being somewhere between 5.0 and 5.5gn), watching for pressure and either tracking group size or velocity, whichever is your goal.