Spare bolts? Yah. WHole spare BCG... not so much. Although if you like building ARs, you eventually wind up with them.
No, Carriers and bolts are not universally interchangeable across all ar-15 pattern guns.
5.56 and 300 blackout guns use the same bolts.
7.62x39 and 6.5 grendel use the same bolts. (bolt face is .445" diameter)
6.8SPC uses something real close to the bolts (bolt face is .442" diameter)
Then you have pistol caliber BCGs which don't have a bolt, and are very different from a standard mil spec 5.56 BCG.
Then you have annoying bullshit like wonderbolts and other things that start messing with the lugs and have to be headspaced different or need special extensions. Avoid them.
As for the BCG, all those bolts will fit in a standard carrier. But if your gun is a piston/op-=rod gun and not a normal direct impingement gun, the BC is non-standard. Additionally if your gun is set up with a roller camp in (this is a POF gun thing), you can't use a normal carrier with a normal cam pin. This stupidity looks like this. I mean it works, but it fixes a problem that doesn't exist and creates proprietary uppers that don't work with standard BCGs right.
Headspace is the measurement telling you how the bolt fits to the chamber/barrel extension. Too much and too little means the gun will have issues, potentially catastrophic if it is too far out of spec. Hence go/nogo gauges. In spec bolts will generally mesh with in spec barrel extensions and everything will be fine. If you want to be certain it is fine, you get go/no-go gauges. You can also do a ghetto version of this by using an in spec round and a couple pieces of masking tape. As mr. google about that if you need to know.
Typically what fails is the following in the BCG area.
1) Bolt cracks at the camp pin hole. This is the #1 failure mode over time... by a lot.
2) Bolt sheers a lug. This is what everyone worries about, and is much less common. It happens, but typically the gun will keep running, possibly less reliably, but keep running. It is an inevitable failure mode over time, but the reality is you usually never get here because of #1 unless there is a defect in your bolt.
3) Gas key comes loose
This isn't a common long term failure mode. It is however something that can happen because the BCG wasn't built right or something was defective. This will usually happen fairly early on if it is going to happen.
4) Gas key cracks or is eroded. This is a longer term failure mode. It is the result of the gas key and the gas tube not being concentric, and is typically due to an assembly error on the upper, or a seriously out of spec key on a carrier. But the tube and the key rub when the BCG goes into battery, and if that wear is not symmetrical, you can chew one edge of the key or tube away and get a gas leak and the gun doesn't run reliably any more, or at all. Worst case is asymmetrical rubbing turns into impact rather than just rubbing, and this can damage the gas tube, or crack the gas key, or cause the gas key to loosen. Spares typically don't help here because the root cause is typically a misaligned gas tube, and the damage occurs to both the gas tube and key so a spare BCG is insufficient.
This is a solid list of spares. I'll just add that you can buy bolt rebuild or bolt spare parts kits that are basically all the BCG bits of this in a container. I will also add that a lot of fancy BCGs are doing something where the tradeoff is less reliability.
I agree with you and the keep a spare, fully populated bolt in your kit idea. I do that as well as keep a box of replacement parts.
Aww.. you should give your opinions on coatings. That's the kind of stuff we are here to argue about.
I will.
COATINGS ARE BAD.
SURFACE TREATMENTS ARE GOOD.
Coatings sit on top of the metal. Surface treatments basically become one with the metal due to chemicals transformation.
Also "nitrided" is an ambiguous term, and it has started to be abused in the retail sector.
Mil-spec phosphate is fine. It is a surface treatment.
IMO the only improvement on this is going to a polished, melonited carrier. This may also be called a nitro carburized, QPQ, or nitrided. Why is this potentially better? There are only really three ways to mess up a mil-spec carrier. 1) machine it out of spec, and this isn't really something you can tell from advertising, and is an issue of QC for a given brand. 2) Attachment of the gas key. Which is once again a QC issue, but if the marketing pics don't look like they did a good job, they probably don't do a good job. 3) Do a poor job at applying the chrome coating in the inside of the carrier where bolt goes. It's part of the mil-spec requirements, but just by it's nature there's minimal room for error, and chrome is chrome and can fail in addition to the channel being machined out of spec, or the polishing step being done wrong and driving it out of spec dimensionally. For a melonited carrier, the coating can't fail. If machining and polishing were good, melonite won't alter the dimension or finish. And polished melonited carriers are easier to clean than phosphated. Also polished and melonited can't hide any sins in machining or surface prep. The matte phosphare can to a small extent.
Things like TiNi, Ion bond, NiBoron, etc are coatings. They can flake off, and potentially interfere in the smooth operation of the gun. This is primarily a concern of chrome and nickel boron as they are thicker coatings, and one the coating is compromised, the damage will likely spread. TiNi, ionbond, and many others are PVD coatings, much thinner, and damage is less likely to spread. They are probably ok, but why pay for them when the better choices are cheaper?
Unfortunately some PVD coatings are black and contain nitrogen and will be referred to as nitride. So do some digging.
Personally I've been very happy with BCM mil spec BCGs, JP, PRI, rubber city armory, and spikes melonited BCGs.
As for bolts, I just buy JP bolts and let my wallet complain. They are the only company that puts extra meat wound the cam pin hole without doing something else stupid. Their QC is excellent and they insist on pretty tight tolerances. Many of the good, more boutique barrel makers head space to their bolts because of this. And their warranty and CS was good 20 years ago and is still good today. That's from personal experience. I know a lot of people who use their stuff, and I've never run into anyone with anything bad to say about them. They are pricey, so I don't indulge in everything they make, but their bolts are worth it and I've just stopped dicking around with anything else.