Everything posted by T Bill
-
Some handgun suggestions
Slightly used Colt Gold Cup listed F/S over at NJ Hunter.............Asking $975.00 http://www.newjerseyhunter.com/forums/82-classifieds-free/186236-f-s-colt-gold-cup-national-match-mk-iv-80-a.html All the bells and whistles are here, stainless, NM barrel and barrel bushing, adjustable trigger, fit and finish, lowered and flaired ejection port, polished fee ramp, etc.
-
Giraud annealer soon to be released, induction annealer!
Interesting to see the price of this setup. Fluxeon "Annie" is $500 on the street, if you can get one, been backordered for months. You can do it by hand also, each case takes less than 2 seconds. https://youtu.be/q2xkf6NPOrw
-
question for you AR guys ??
Easy to do if you have the tools. Remember your feed ramp combos esp for the upper. No M4 feed ramp upper with a standard feed ramp barrel extension.
-
I'm crushing my .223 reloads
Trash the bad primed brass. Without experience depriming live primers is dangerous. Ways to do it, but it is not worth it. The brass you are priming, are the primer pockets crimped? Need to ream them out first. Primers that are difficult to seat are usually due to crimped primer pockets. You can always load the brass empty in the gun and fire the primer. NO bullet or powder. Is it possible your die is set to low and crimping the bullet in place before it is fully seated? Run the die out of the press. Raise the ram all the way with the brass in place. Now screw in the die until it just touches the brass, back out the die 1/8 turn. Now back out the seater stem. Put a bullet in the case mouth, run it in the die and with trial and error continue trying to seat the bullet to the depth you want by turning in the seater stem. NO LUBE on bullets. Does it still crush the case? If so, check the expander in the resizing die. One of your steps is out sync with the others. Sounds like your expander ball is not where it belongs in the sizing die, check that. Brass gets resized all the way into the die till it touches the shell holder.The expander should be set to true the case mouth down to the shoulder.
-
Sighting in rifle scope at the range
I would think it is something you need to bring.
-
any experience with McGowen barrels?
I have barrels from them. Both are great. Waited a while (3 months) but got exactly what I wanted. Fit finish spot on.
-
AR15 Opinions
Sounds to me like time for a build. DO NOT start changing that M&P around. Waste of time and money. Just shoot it and start putting your dream build on paper. New product is announced all the time. Who knows you may even change your mind while building it.
-
Some handgun suggestions
Based on your cut list in your post it looks like the caliber of choice is 45ACP. Research internal vs external extractors. I'll help you here, get an internal one. US made from a company with a good 1911 track record and good customer service. When it was my time for my first, it was a Colt Gold Cup National Match. Rock solid, no complaints, years of reliable service, plenty of aftermarket parts for any reason you can think of! BOCO. Para Ordance is part of Remington and scheduled to be rebranded just like they did to Marlin. Do Not expect any great things here. Remington's track record is not good when they play musical plants with their product line. Ruger's product has been out for a few years. Nice quality. Good CS and stands behind their product. Remington I cannot speak about, no experience here. I personally do not like Remington. Just me. The more you stick to a "Series 70" or "Series 80" design style in 1911 the easier it will be to get parts and do upgrades in the future to.
-
3000 Lowers Seized from Stag Arms
I have gone through Federal and State audits many times, not in this industry however. First of all they never just show up. Either you know they are due to knock on your door, or you get a heads up somehow. We all knew come middle of June to expect them. So we made a special effort to may sure everybody was on point. No matter how we tried to satisfy every regulation there was always more rules and regs that seem to appear. We would address the noted points in the audit, and new ones appeared at the next audit. How? they were not mentioned at the last audit and nothing changed. We were flat out told you could never have a perfect audit even if you did everthing correct. They will always note something to make it look like they are doing their job. I bet you this was a new agent that performed the audit, a gung-ho newbie or one looking for a promotion with an axe to grind. Or, as stated, an employee that felt maligned. Looking bad for them, their laziness and lack of ensuring policy enforcement may have caught up with them. It could have been from trying to keep up with the sales demands. The Feds are not in the habit of harrassing you unless they know they got you.
-
Large capacity / Extended length Handgun magazine
More BS walks out the doors of most gun stores than guns and ammo combined. I have heard and seem more crap originate from behind the counter and I get so PO'd at times I just leave the store. I wish they would just learn and keep to the facts and let the BS walk. Instead of helping our cause they create more disinformation than the press. This is why there are very few NJ stores I check out anymore. Not even to look at the 'used' rack. I realize the brick and mortar stores are struggling, but really, some informed customer service and 'how can I help you' attitude wins alot of points. When there is no 'value added' to the sale, what do they really expect? Just a special note............Kudo's to those vendors who participate here, they are the welcomed exception. It is refreshing to read their posts and know they know what the real deal is.
-
Large capacity / Extended length Handgun magazine
Not yet in NJ. I believe CT does have something to the effect that a magazine cannot extend beyond the butt of the handgun but not sure on it. I understand even CTers are not sure of the meaning of the law.
-
Glock .22 conversion slide
Got the AA kit also for the G21. Runs great. Loves the Federal bulk 36gr copper tops. It maybe harder to find than 22LR. Lenny Magill's? Slowly I turn step by step.................... (don't like his business practices). PK Firearms has it in stock for $293 shipped.
-
OAL Question - 223 REM.
Check/Clean your seating stem in the die first
-
Shotgun Shootout! @ Clinton WMA Saturday 5/30
Sorry. Parade day.
-
Where can I look at Over/Unders?
Take a look at the Benelli 828U, at $2500 list, it's supposed to be a real fine sporting arm for the price.
-
Got my first 3 firearms
You certainly did as the Marlins are not what they used to be, IMHO, since Remington got a hold of them. Plenty of aftermarket items for those Rugers.
-
OGAM question (private sales)
That list looks like some of the new laws the new govenor will pass in 2017.
-
Where can I look at Over/Unders?
Kicks Beretta's butt. There are six USED F.lli Bertuzzi's on the G&H site right now from $240,000 to $295,000 apiece.
-
Where can I look at Over/Unders?
Shawn, there are Sporting versions and Parallel Target versions. In the PT version there is shortened and standard, that refers to the LOP, either 13.75 or 14.75. Kick-off models cannot have their stock length adjusted. Gun Pod does not come with Kick Off. Some question if Kick Off is worth it when only shooting trap or SC loads. Gun Pod is seen as a overkill.
-
Got my first 3 firearms
Stick them in a bag of your choice, toss them in the trunk and get to the range. Get a nice 4 power for the RAR and a nice red dot like the Bushnell TRS-25 for the takedown. When your ready let us know and we'll help you adjust that RAR trigger and drop in some nice aftermarket parts on that takedown. You won't be disappointed. Love them Rugers in 22LR they are nice. Closest second to them for me are my old Marlin Model 60s, you know the ones that NJ considers assualt weapons because of their over limit tube feeds (fixed that with a dull tubing cutter).
-
Anyone reload 5.56?
I will continue to reload most of my own ammo with the exception of rimfire of course. You may not be able to save on some caliber reloads but, as stated, you get what you want. Some may love that commie blasting ammo but for me it doesn't cut it. I have given up on foreign milsurps because they basically do nothing for me anymore, been there done that. I'll spend my dollars with US made firearms, and supplies, even if I have to put them together myself.
-
Where can I look at Over/Unders?
For crazy insane prices see Griffin and Howe. Some very fine firearms there. I find it funny every once and a while they have a "Average Joe" on the shelf. Who would have known.
-
OGAM question (private sales)
Yup. Seller still has to send in the copies to Issuing Department and NJSP all filled in with date and such, so that kinda puts the buyer on the hook for adhering to the law! Dates on the P2Ps are the key! And the postmark on the envelope is within 5 days of the sale date on the P2P!
-
A3666: Prohibits mail order/internet/phone sales of ammunition
It's from our own Rep. Watson-Coleman, you know the one whose kids committed armed robbery, then she authored a law so employers cannot ask about criminal background during interviews, and lately those two felons are supposedly working for the county. Nice deal if you can get it.
-
Anyone reload 5.56?
Hold onto that brass. It doesn't eat or drink so one never knows what the future holds. Get 1K of them and sell them off, or who knows you may be just reloading before you know it.