Everything posted by CAL. .30 M1
-
Single stage reloading press
@Mrs. Peel i think the OP's threads need to be merged... You should NOT start with rifle ammo as a new reloader....especially for a semi auto rifle...
-
I have now seen the light, and need your help. Time to get into reloading, and am a noob.
Are you reloading for a bolt gun or semi? My recommendation is that a new reloader, NOT start with rifle rounds...especially hi power semi auto
-
Single stage reloading press
Its old school stuff but works....
-
Bullet seating and dimensions
No go back to square one.... readjust all dies... You only need to truly add the taper crimp...
-
Reloading components swap
-
Suggestion for a Handgun to try out
Small.medium.hands..... 1911 Browning hi power Cz75 S&W 'K' frame in 4" S&W Semis in single stack Your going to have an issue with double stacks...*but* the G19 is surprisingly fine
-
Bullet seating and dimensions
It is not that difficult - to achieve a catastrophic failure in the load stage - it depends on your workflow - it is FAR less likely to double charge a progressive for the simple fact that the pull level indexes the cases - so the same case can never be in the powder charge slot twice - however, I still like the lockout die. Example - I am loading pistol powder in rifles for cast bullets - the window is 16-18 grains of 2400...no more no less. Each case gets charged and a bullet placed on the case mouth to indicate it was charged and ready for seating....if for some reason there is even a slight thought of did I charge that case...the entire lot get's heads pulled and powder back and I restart..I do 20 round lots. For pistol I am progressive - but you issue in the OP - is the taper crimp...the plunk test in your barrel tells you something but not everything. Get the gauge....
-
Bullet seating and dimensions
You can and possibly will blow up a gun *IF* you double charge - get one of these....: This is to prevent over or under charge in a progressive press - but being you are single stage - you need to be METICULOUS on the charge step of your workflow....if you double charge...well BOOM....under charge - squib and if you do not realize it - well you can get a boom if you pull the trigger again....
-
Bullet seating and dimensions
This is becoming too complicated for you - All pistol ammo should have a slight taper crimp as the cases head space on the mouth of the case. It should be tapered enough to remove the bell from the flare to get the bullet started. *if* you are tapering or crimping too much you get a bulge that prevent chambering as you are experiencing *if* you do not taper enough you are not removing the flare. These are NOT gross die adjustments, they are minor till you get the sweet spot. You do NOT need any additional items other than the dies you have and when set right will do what you need. I use hornady and am loading 147grain flat nose without any issues whatsoever. SAAMI for 9mm is: if you are loading to 1.164 COAL on the flat nose bullet, of which has a different profile than a round nose - you need to adjust COAL based on that bullet in SAAMI spec range and place it in a guage - more on that later..... I can see the issue in the round in your OP - the flair is still there and you did not do the proper taper crimp. Also buy on of these: https://www.brownells.com/reloading/measuring-tools/case-gauges-headspace-tools/9mm-luger-cartridge-gauge-prod99044.aspx If it fits in here - it will fit in ANY 9mm chamber that meets SAAMI specs
-
“Son, only a pimp in a Louisiana whore- house carries pearl-handled revolvers." General Patton
While i LOVE my rifles....nothing is as collectible ad various handguns....i venture a guess you can collect smiths as you say..for a lifetime... ..
-
“Son, only a pimp in a Louisiana whore- house carries pearl-handled revolvers." General Patton
I have a well carried victory revolver...that has the been there done that look....super tight lockup and fantastic bore....mus have been carried quite a bit though...and shot little....i need to paper it.... Waiting for @Pizza Bob to chime in....lol
-
Searching or my 1st purchase
Why don't you start here !!! https://www.anjrpc.org/page/train_class_schedule#NRA_Basic_Pistol_Classes NRA BASIC pistol class.... west caldwell is over by old bridge right??? Paging rosenthal, @Smokin .50 to the white courtesy phone please.... new shooter needs some assistance. Buying a FIRST gun is not like trying on pants....frankly, and no offense intended, you do not have the skill set to make judgments as to what is right or wrong....other than what might look cool to you. get basic training first....learn basics first....then when you have a good foundation...go buy something. MY first HG, was a G17...never ejected right....why limp wristing......brought it back...old guy says try this with this ammo.....he handed me a Model 19 4inch and 250 rounds of 38 wadcutters... the rest is water under the bridge. With a revolver it is simplistic....brute force reliable, and easy to see and understand mechanics of double and single action shooting. Will also help you establish proper grip trigger control etc...with a strong but not overpowering round....and if needed can do fine as a good self d gun....when you need it to go bang, pull the trigger...if it doesn't go bang pull the trigger again...and keep.pulling till it goes bang..or you need to reload... You can also swing by @gunforhire and check some things out.... My girls learned to shoot on the same model 19... This is not a difficult process....
-
“Son, only a pimp in a Louisiana whore- house carries pearl-handled revolvers." General Patton
Nice gun...really though, lose the stocks..... I like bone better....i have a set of stags on my model 19 round grip snubby. Let is know how it does !
-
Anyone use Large Magnum Pistol primers for .45acp?
Everything that @Heavyopp said. Start at a beginning load and looks for pressure signs.... All the springs in a 1911 make it run right....recoil, firing pin and hammer..and don't forget the trigger return grip safety etc...all need to be tuned right. Change the recoil spring....you gotta change the hammer spring..etc... The biggest issue you have is the narrow window of loads available prior to max... Is your measuring equip spot on?
-
Searching or my 1st purchase
GREAT !!!!!! Where r u located? A Glock 17 is NOT starter handgun imo.. A revolver is brute force reliable and a fantastic weapon to start with... Mag fed semi auto weapons can be finicky....and reliant on many factors to work right...
-
Anyone use Large Magnum Pistol primers for .45acp?
What 45acp are you loading for? Is it properly sprung? You will not blow yourself up... Start with a starting load off by 5% ....look for pressure signs and go from there...
-
Searching or my 1st purchase
Your choice for a g17 as your FIRST handgun is a mistake... Have you any training? Have you EVER fired a 9mm before...? Do you know what limp wristing is...? A stovepipe? A FTF? An FTE? Do u understand sight alignment? Trigger control? U have not been counseled properly...you have been sold an item..... Basics basics basics basics....
-
Searching or my 1st purchase
Very accurate......hmmm Limited capacity... (scratches head) Average rounds fired in a self defense situation is 2.2.... Your fight is going to last as long ad your ammo... This is tje OPs FIRST handgun.... he needs to learn the basics.... once the basics are sound he can move to the next phase... I carry a 586 with 357 mag rounds and two reloads on speed loaders in the woods hiking where legal...i don't feel undergunned.
-
Searching or my 1st purchase
Your VERY first gun? I’m looking for something really simple Smith & Wesson Model 10 4" Revolver in 38 Special. Learn to shoot that first with target wad cutters.
-
And Now for Something Completely Different...
Ruger # 3 from 1973 - 1986
-
Reloading components swap
- OK here we go - and looking to see - 30-40 Krag Brass - will trade a lot of different brass - all MIL calibers Anyone?
-
Africa
We hung these folks out to the commies...
-
Model of 1898 - 30-40 Krag
.....ahhhh cherry ridge.. 100yd line.... when all the fancy schmancy newfangled optics boys need benches mounts sleds etc..to shoot targets at 50 to 100yds...and cant hardly hit crap... And when 52/60 rounds of wheel weight hand loads slams steel time and again...off hand... And they just look ..... priceless... 17gr Alliant 2400... lr primer... cast wheel weight 168 grain drops at like .312..sized and lubed to .311 ...with gas check.... nice soft shooting... paper next time see how she groups...and no signs of pressure spike.
-
Model of 1898 - 30-40 Krag
..whaddya got specifically.... cost? Always like to have some factory on hand and not just my handloads !
-
REDUCTION - Bass Boat Bass Tracker Pro-16
M1903?