Skip to content
View in the app

A better way to browse. Learn more.

New Jersey Gun Forums

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Is there any kind of a solvent for Red Loctite?

Featured Replies

...besides an acytelene torch?

 

I put a set of XS dot sights on my glock a few months ago. Only shot it twice since then, once was at the first IDPA match I went to, then I went to the range on Friday for some more slow paced practice/technique shooting.

 

It's looking like I didn't get the rear sight centered on the slide. It's just a *smidge* left of center, but it's enough that if I line up the front sight with the rear line exactly, I shoot left of center on my target .

 

I am quite annoyed with myself.... :evil:

 

So, any options for removing red loctite that will preserve the rear tritum sight without burning it up and the finish on my slide? I used a lot of it underneath the rear sight and in the small allen keys on the top.

So, any options for removing red loctite that will preserve the rear tritum sight without burning it up and the finish on my slide? I used a lot of it underneath the rear sight and in the small allen keys on the top.

 

:roll: In this case, more is not better. And blue is your friend, not red. :oops:

 

Have you tried a heat gun? I don't know how hot a tritium sight can get without melting/failing.

 

At worst case, I would attach the hex key to the fastener first BEFORE I applied heat to try to use it as some sort of a heat sink - or even try to heat the end of the hex key prior to inserting it in the fastener and just use heat transfer...

 

Where are you located? If you don't have a heat gun, I could loan it to you.

  • Author

DJ,

 

I'm in Morris County, near Morristown. Heat gun loan would be appreciated, but I'm going to contact the XS sight people first to see if they have any suggestions or if heat will damage the tritium in the rear sight.

The only way to remove red loctite without heat is excessive vibration. You could use a heat gun if you didnt put a huge a mount if not get a burnsamatic torch for like $20.

DJ,

 

I'm in Morris County, near Morristown. Heat gun loan would be appreciated, but I'm going to contact the XS sight people first to see if they have any suggestions or if heat will damage the tritium in the rear sight.

 

I'm up 287 in Passaic County near Riverdale. Let me know if you need - I'll work something out with you for sure.

 

I also work in Belleville if that makes life easier - just a couple blocks from TBH.

If you're gonna heat the tool, I'd use a torch rather than a heat gun since you will have really localized the heat source at that point.

How bout a soldering iron to heat the screw itself? Seems more direct than heating the tool, and waiting for the heat transfer.

  • Author

Thanks for the replies and offers all.

 

There is loctite not just on the set screws, but all under the base of the rear sight itself, in the dovetail channel.

 

I followed this yahoo's instructions when mounting it:

 

XAahHP7z7so

 

Poor judgement on my part.

  • 1 month later...
  • Author

Following up on this, finally got the XS sights off and replaced with regular night sights.

 

I ended up detail stripping the slide and putting it in a toaster oven at 450 degrees for 10 minutes. This softened the loctite enough that I was able to remove the front sight screw and loosen the rear sight set screws. Several sharp taps with a hammer and delrin punch loosened up the rear sight. Had to do a bit of de-scaling with a sharp pin to get all the loctite out of the front sight hole and rear dove tail.

 

Unfortunately this also melted the plastic mount for the tritium vial in the front sight, but the tritium vial stayed intact.

 

It also melted the firing pin channel liner in the slide (*oops*, forgot that was there). Luckily that just fell out instead of adhering to the slide and was only a $3 replacement part.

 

Lessons learned:

 

- Make sure your sights are aligned correctly, that they allow you to shoot accurately and you're satisfied with them before locking them down "permanently"

 

- Don't blindly follow everything that guy from tactical response advocates

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Recently Browsing 0

  • No registered users viewing this page.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.