Skip to content
View in the app

A better way to browse. Learn more.

New Jersey Gun Forums

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Anyone know(or is) an Electrician that'll travel to Vernon?

Featured Replies

Got a problem I need addressed by someone competent.

Try this guy Mark.

Steve Maciag 973-875-2039 or 1800-867-5998

He is located in Augusta, so it is not that far to Vernon. We have used him multiple times both in our old and new houses. Whats good about him he calls you back (contractors don't do that often), and he actually comes when he says he is. And his prices are very reasonable. He has an ad in the yellow pages under electric contractors.

Mark, I'm an electrician, what's the problem?

  • Author

We have a 50amp 220 breaker on the main panel that powers two sub panels. Two 110 lines and the 220 water heater in one box and a septic pump in the other. The issue is one of the 110s is dead and of course, none of the 220 stuff works. I think we've figured it out though...looks like a blown element on the water heater. Going to change it in the next hour or so, see if that solves the problem.

We have a 50amp 220 breaker on the main panel that powers two sub panels. Two 110 lines and the 220 water heater in one box and a septic pump in the other. The issue is one of the 110s is dead and of course, none of the 220 stuff works. I think we've figured it out though...looks like a blown element on the water heater. Going to change it in the next hour or so, see if that solves the problem.

 

Any questions, give me a call, 201 726 5690

Do you have a tester?

Do you have 220 at the water heater ? If not I dont think its the element unless your using 2 single breakers to feed it and you popped one !

 

Also you have a 50 amp feeding a hot water heater + septic pump I'm surprised the 50 isnt poping when they both kick on, I would think your over the 80% !

 

You should pull a new feed to one of them.

Hey Mark you have us sitting on the edge of our seats.....

 

Did you fix it? I didn't hear from you.

 

Frank

  • Author
Hey Mark you have us sitting on the edge of our seats.....

 

Did you fix it? I didn't hear from you.

 

Frank

 

Sorry, lol. After fixing it and shoveling snow, I took a nap.

 

Fixed it....at least I put new elements in the tank and everything is normal again.

 

I tested the old elements and both show continuity, maybe they go open when they heat up a little. I dunno. I replaced both with Nickle plated low density elements in the hopes they last a while.

 

Thanks everyone, specially Frank. You key'd in on it for me.

Did you replace the upper and lower thermostats as well?

 

Usually if you get continuity across an element, the element is fine.

 

I have seen a bad upper thermostat cause breakers to trip, if both elements try to heat up at the same time.

  • Author
Did you replace the upper and lower thermostats as well?

 

Usually if you get continuity across an element, the element is fine.

 

I have seen a bad upper thermostat cause breakers to trip, if both elements try to heat up at the same time.

 

Well, the problem was that one of the 110 legs in the same box would show voltage on a meter from the hot to the neutral but the moment you put a load on it, the voltage would drop to like 40 volts.

 

The tank is only 5 years old, so i'm guessing it was just bad elements. It appears to be working now, so unless something else happens again, I'm going to declare it fixed.

Did you replace the upper and lower thermostats as well?

 

Usually if you get continuity across an element, the element is fine.

 

I have seen a bad upper thermostat cause breakers to trip, if both elements try to heat up at the same time.

 

Well, the problem was that one of the 110 legs in the same box would show voltage on a meter from the hot to the neutral but the moment you put a load on it, the voltage would drop to like 40 volts.

 

The tank is only 5 years old, so i'm guessing it was just bad elements. It appears to be working now, so unless something else happens again, I'm going to declare it fixed.

 

Check your neutrals all the way from the service to the branch circuits.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Recently Browsing 0

  • No registered users viewing this page.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.