Skip to content
View in the app

A better way to browse. Learn more.

New Jersey Gun Forums

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Where to get parts/repair service for a portable Makita air compressor?

Featured Replies

Got a Makita portable air compressor that a buddy gave to me when he was moving. Don't have the model #/specs on me, but it's a 110V "plug-in-the-wall" electric compressor with two smallish tanks. I think it's ~10 years old.

 

When I turn it on the motor runs for a few seconds and then it slows down and stalls. If I open the drain valves on the tanks so that air can freely flow out then the motor will run and run without slowing down.

 

I suspect the "check valve" (is there a better technical term for this?) is failed open, so that the piston/cylinder is essentially directly connected to the tanks and once the motor runs for a few seconds it's trying to compress the entire volume of air in the tanks instead of just what's in the cylinder which is why it bogs down.

 

Should I bother trying to fix this, or am I going to spend more in time hunting down the parts and replacing them than it would cost me to just get a new one?

sounds like it may be a faulty pressure switch.

 

 

When you have the drain valve closed, the pressure switch is what tells the motor to turn off at XXX PSI, when faulty it will mis-read and turn off prematurely, Which explains why it runs when you have the drain valve open - it wont allow the pressure switch to register any sort of reading since it's free flowing right out the drain.

 

EDIT: just re-read your post, missed the " slowed down and bogged " part...let me re think this...... you might be on the right track with the check valve

or your motor is just about done.

Got a Makita portable air compressor that a buddy gave to me when he was moving. Don't have the model #/specs on me, but it's a 110V "plug-in-the-wall" electric compressor with two smallish tanks. I think it's ~10 years old.

 

When I turn it on the motor runs for a few seconds and then it slows down and stalls. If I open the drain valves on the tanks so that air can freely flow out then the motor will run and run without slowing down.

 

I suspect the "check valve" (is there a better technical term for this?) is failed open, so that the piston/cylinder is essentially directly connected to the tanks and once the motor runs for a few seconds it's trying to compress the entire volume of air in the tanks instead of just what's in the cylinder which is why it bogs down.

 

Should I bother trying to fix this, or am I going to spend more in time hunting down the parts and replacing them than it would cost me to just get a new one?

 

A Makita compressor is fairly expensive. There's clearly something going on with the pressure sensing or it's just adjusted very low.

  • Author

Although it's possible, I doubt the problem is the motor. This unit was not used heavily from what I understand - it was my buddie's air source for filling up his tires at the race track on weekends, not driving a nail gun 5 days a week for a roofer.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Recently Browsing 0

  • No registered users viewing this page.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.