Skip to content
View in the app

A better way to browse. Learn more.

New Jersey Gun Forums

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Can you tell when you're rounds are too hot/compressed?

Featured Replies

I'm not talking about a double charge. I think that would be very obvious. What I'm talking about is more if

your rounds have an OAL that is too short and there is too much pressure in the load. Or perhaps you are actually

loading above the max load/never exceed load by a little bit (a grain or two perhaps). When you fire the rounds

will you immediately be able to tell that they are too hot? And what kind of damage would this do to the gun?

 

I'm asking because I load at the start load and don't go much beyond that. Some of my recent 45 ACPs are closer

to the max load and are on the short side (not below min OAL but still closer to the min cause they are hollow points).

 

I have shot some and from what I can they feel like factory loads. If I'm running to short too hot will I know right away?

I'm not talking about a double charge. I think that would be very obvious. What I'm talking about is more if

your rounds have an OAL that is too short and there is too much pressure in the load. Or perhaps you are actually

loading above the max load/never exceed load by a little bit (a grain or two perhaps). When you fire the rounds

will you immediately be able to tell that they are too hot? And what kind of damage would this do to the gun?

 

I'm asking because I load at the start load and don't go much beyond that. Some of my recent 45 ACPs are closer

to the max load and are on the short side (not below min OAL but still closer to the min cause they are hollow points).

 

I have shot some and from what I can they feel like factory loads. If I'm running to short too hot will I know right away?

 

Load up some rounds incrementally hotter, and check each piece of brass after you've fired it. Telltale signs of overpressure would be pierced primers(the primer strike will be black) and flattened primers. Also, preliminary pressure signs would be "marbelization" of the brass itself. Look at it in good light compared to a starting load and you'll be able to tell the difference. IMO most "max" loads are still way light. As always the best tool you can use when working up a load is a good chrono. I personally feel no need to load hotter than 135 power factor for 9mm, and 170 power factor for 45.

The bullets you are using should have a recommended OAL. If you load under that and at the top of the data then yes you will have over pressure rounds. It is ok to go under the OAL as long as you start at the bottom of the data. You will be able to tell by firing it if it is hotter than normal. Also get multiple load books because what is max in one book is only low middle in another. The differences in printed material will amaze you. DO NOT rely on primers as your ONLY indication of high pressure, they can fool you. The smaller the round the less powder it takes to screw it up.

  • Author

No pierced primers from what I've seen, but at the same time I do pick up surrounding brass near my booth

that was not fired from my gun. Even still I have not noticed anything strange from the brass I know was

mine. But good to know what to look out for.

 

I've not found load data specific to 200gr hollow points, plated, (I use Berry's). I based it off lead

data and 230gr hollow point data and tried to find a medium. I know that's not the best way, but couldn't

find other data. I do want to get another load manual though.

No pierced primers from what I've seen, but at the same time I do pick up surrounding brass near my booth

that was not fired from my gun. Even still I have not noticed anything strange from the brass I know was

mine. But good to know what to look out for.

 

I've not found load data specific to 200gr hollow points, plated, (I use Berry's). I based it off lead

data and 230gr hollow point data and tried to find a medium. I know that's not the best way, but couldn't

find other data. I do want to get another load manual though.

 

Use data for 200gr SWC bullets.

  • Author

Use data for 200gr SWC bullets.

 

Yup,that's pretty much what I did while referencing with

other hollow point data. Thanks.

 

Gonna use them for steel tonight so we'll see.

  • Author

Got to test out my loads tonight and they worked fine. Nothing felt hot at all.

I actually accidentally mixed the rounds where I used 5.3gr and 5.7gr and I could

not tell. Then again it was a steel match and sometimes you're not even paying

attention to that stuff cause you're so focused on the targets.

Got to test out my loads tonight and they worked fine. Nothing felt hot at all.

I actually accidentally mixed the rounds where I used 5.3gr and 5.7gr and I could

not tell. Then again it was a steel match and sometimes you're not even paying

attention to that stuff cause you're so focused on the targets.

 

What powder are you loading with?

Got to test out my loads tonight and they worked fine. Nothing felt hot at all.

I actually accidentally mixed the rounds where I used 5.3gr and 5.7gr and I could

not tell. Then again it was a steel match and sometimes you're not even paying

attention to that stuff cause you're so focused on the targets.

 

 

You should buy a chrono asap.

  • Author

What powder are you loading with?

 

Accurate #2.

 

Never bothered investing in a chrono cause I never

thought I'd get that into it, but apparently I'm

headed that way...

  • Author

No 2 is a very good target powder..excellent for steel also..i used it in my .45 uspsa ammo and i use #5 in my 9mm uspsa ammo..

 

Well good to know cause I bought it just cause I had the most load data on it and it was cheap, lol!

I honestly could not tell a good powder from a bad one since this is the only stuff I've ever used.

I started thinking no one liked it cause every reloader I've spoken to uses something else.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Recently Browsing 0

  • No registered users viewing this page.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.