April 29, 201214 yr I had to return my 8-9 month old Ruger SP101 .22LR to Ruger because it was not functioning properly. It appears to have had excessive play in the cylinders as they rotate, and a couple of cylinders would not fire with each time each set of eight rounds was loaded. Also, when ejecting, not all of the rounds would eject all of the time and often get stuck under the ejector. I Emailed Ruger CS and did not get a response at all (even to this day), and a couple of days would have been reasonable for them to respond. After waiting those two days, I called them directly and Ruger had UPS come and pick it up right away. We arrange to have it picked up within a couple days, and I was given essentially a whole day window to wait around for the UPS drive, and neither Ruger nor UPS could provide me with a smaller window. And, of course the driver came within the last 30 minutes or so of that whole-day window to pick it up. I had to include the revolver, box, and a description of what was wrong with it. It shipped out on a Thursday. I contacted Ruger on the following Tuesday to check on it. The representative, who could have been nicer to me and seemed to have a slight bullet stuck up his barrel, told me that it was most likely there, but that they would not get around to looking at it for about a week because they were so backed up with shipments that they had received. He told me to call back Thursday or Friday of the following week to check on it. On Friday I called back and again there was a slight attitude and not too helpful persona, but I was told me that it had been checked in but that it had not been looked at and to call back the following Thursday or Friday to check on it. So, I waited. On Thursday of the following week (2 weeks after the initial shipment), I called them to check on it and they said that it had been shipped out on Tuesday and that I should receive it on that very day (Thursday when I called). I asked over the phone if the rep could tell me what had been wrong with it, and after waiting for about a minute on hold, he came back on and told me what was replaced. He was a little more friendly than the two reps in the two previous calls. Ruger replaced the firing pin, recoil plate and spring, cylinder, pawl, cylinder latch, trigger and trigger plunger. Overall, the customer service was OK, but I would have liked some form of contact to let me know on what day it was coming back to me, as they had my phone number, Email, etc.. If I hadn't called I would not have known, and again, it took the whole day of waiting around to receive it and required an adult over 21 to sign for it. Ruger had a really good turn around time and they paid for the roundtrip 2nd day shipping. The time away was exactly two weeks with 4 of those 10 business day for shipping. I had included a couple of questions in my letter description of the problem and not a response. There was not a word, offer or anything, though for my trouble of being without it for a couple of weeks. I would have liked a coupon or something, though. Because of the low serial number of the one I had, it was probably one of the guns in their first batch of these new .22LR revolvers, and it might have had some growing pains. I hope now it is working properly. I will update you after I get a chance to take it to the range. But I will say, that one, I no longer have the broken in trigger (after putting about 1500 rounds through it) and that the hammer appears to be a different shape than the one I had in it before and that the already heavy trigger pull seems to be even heavier, now, in double action firing. This is disappointing, as one of the things I wrote in the letter to them was that I wanted to know if there could be some way to improve on the pull weight, as my wife and niece cannot shoot it because either pulling the hammer back or pulling the DA trigger is too heavy for them. It's ridiculous when a relative of mine's old cheapie Hi Standard .22LR revolver from the 70s has such a better trigger pull. Lastly, the stock Hogue grip that came with it with the inlaid wood seems to be damaged. I immediately swapped it out for another Hogue grip that gave me more purchase on the grip and do not recall having any damage to it. However, it came back to me damaged. I am going to have to place another call to them because I would like it in the new condition that it was when I had to put it back on the gun to ship out. .
April 30, 201214 yr Sorry to hear about your bad experience with Ruger! I dealt with Ruger a few years back, but it was all positive I had a supposedly brand new Ruger Redhawk in .44 Mag that had a very sloppy fitting cylinder and grips that didn't fit properly. They were very quick in resolving he problems and were very pleasant when I spoke with them.
May 1, 201214 yr Author I'm not that disappointed with Ruger, as they did handle the problem with no cost to me, and I assume that they did a good job with it, as long as I have no further problems with my revolver. It's just that they didn't do that extra little special something to make me feel like a valuable customer. I have confidence in them, but they didn't win me over.
May 1, 201214 yr they are just probably extremely busy, thats all. i heard they had to stop taking new orders for a minute because they couldnt handle it, but from what i understand they are taking new orders again. just call them they will take care of ya, if it was an automatic they probably would have thrown in a mag for ya, but its a revolver you are dealing with...
May 2, 201214 yr Looks like a solid revolver but I guess you just don't know until you go out & shoot
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.