Skip to content
View in the app

A better way to browse. Learn more.

New Jersey Gun Forums

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Reloading 223/556 is it a lot more involved than pistol rounds?

Featured Replies

Finally will be completing my AR15 build. I've come to realize ARs are a lot of fun

accessorizing, but boy it costs some major money. Now after everything is built

it's time to feed it. I already reload 9mm and 45acp. I know my Lee Pro 1000 can

be set up to do 223/556 as well.

 

My question is can I just reload it like a pistol round or do I have to do all that trimming,

and measuring of the case (etc, etc) cause it's a rifle round?

 

If it's gonna be much more involved than a pistol round I'll probably just not bother.

I just don't have the patience required to reload to that level of precision. I just wanna

shoot.

 

Lemme know for those of you who reload for this caliber.

On my Hornady L-N-L I resize/deprime on the first pass, then check my brass lengths, segregating and trimming/chamfering/deburring the lengthy pieces. Then I put it through again, this time priming, charging, seating, and crimping.

 

If you want to do it all in one pass, RCBS X-Dies are supposed to keep cases from growing too long by some sort of jiggery-pokery, but I'm not sure how well they work.

 

Edited to add - I've noticed that nearly all LC headstamp brass was too long after first firing, and had to be trimmed to 1.250" (which I liked). On the other hand, Federal 223 was consistently under 1.250". I decided not to load Federal so I'm not sure how durable the brass is, but if you want to skip the trimming step, you might consider using this brass instead.

  • Author

So what happens if you don't trim the cases? Don't get me wrong I'm not looking for any shortcuts as I know

they can potentially be dangerous. I'm just trying to figure out if it's a safety issue, accuracy, reliability, or all

of the above. I know some guys trim pistol casings which is just for extra consistency but not entirely necessary.

 

I skip a lot of the things people do for pistol rounds like trimming, cleaning primer pockets, etc. cause they are

not required and I just want to load as much as possible in as little of time as possible.

 

Newb question: .224 is the correct bullet size for 223/556 right?

Worst case, you pinch the case neck between the bullet and the side of the leede/freebore portion of the chamber cut, spike the pressure, and blow up you rifle and maybe part of your face with it.

Funny you mention the x-dies; i've been using them lately for my 223 and 30-06 reloads and they seem to be holding true to thier claim of minimizing growth. I have only a few reloads on the batch of brass ive been using them with but so far all the cases are still well under the max case length value and in no need of a trim. Reports ive read online state that others are getting not only many reloads on the same brass without trimming, but also longer overall case length due to minimized brass thinning.

 

The way the die works, in a nutshell, is that during resizing, it holds the entire neck and shoulder as a unit and pushes the actual material down rather than to just move the position of the shoulder down. its an oversimplification , but its all about controlling (or limiting) material flow. Traditional resizing merely relocates the shoulder position, it does not actually compress the expanded case length down at all whereas the x-die will actually reduce the shell's overall length during resizing. You do have to prepare your brass specially for the x-die in that for your initial trim, you trim about .010" more than the typical trim to length which allows some buffer room for the case to initially grow and then still maintain an overall length in the normal range once growth stabilizes. No big deal so long as your case trimmer is adjustable and not fixed to index off the shoulder at some static value.

Worst case, you pinch the case neck between the bullet and the side of the leede/freebore portion of the chamber cut, spike the pressure, and blow up you rifle and maybe part of your face with it.

 

Good explanation raz! And that is EXACTLY the situation.

  • Author

Worst case, you pinch the case neck between the bullet and the side of the leede/freebore portion of the chamber cut, spike the pressure, and blow up you rifle and maybe part of your face with it.

 

That's it? Haha. OK, so guess you gotta trim.

 

How long does it take you guys to trim/measure 1000 cases?

 

Jon, I'm a little confused. Is it that when you use the x die you only have to trim the case

one time and then from there on out the x die will keep the proper length?

 

Also will the x die work on a Lee Pro 1000?

That's it? Haha. OK, so guess you gotta trim.

 

How long does it take you guys to trim/measure 1000 cases?

 

Jon, I'm a little confused. Is it that when you use the x die you only have to trim the case

one time and then from there on out the x die will keep the proper length?

 

Also will the x die work on a Lee Pro 1000?

 

After you trim the first time and you trim to minimum length, with a moderate load, you should get 2 or 3 more loadings without trimming.

That's it? Haha. OK, so guess you gotta trim.

How long does it take you guys to trim/measure 1000 cases?

On my Giraud trimmer, I can trim, chamfer and deburr 1000 .223 cases in under 90 minutes.

 

Today brought me back to "prehistoric" reality:

I made 91 .300 Whisper cases from Lake City .223 brass for a buddy who's getting into that caliber.

I had to use my hand-cranked Possum Hollow lathe/trimmer and chamfer/deburr station to do these 91 pieces.

It took me a couple of hours!

 

I'm really glad to have the Giraud, because as a high power competitor, I full length size, trim and clean primer pockets of my match brass for EVERY loading.

And that's after inspecting EVERY piece for split necks and incipient head separation after tumbling them clean prior to decapping.

Precision .223 reloading is a multi-step (approx 15) process, for sure.

Funny thing is I only reload rifle. I toss pistol brass because Its a pain in the but to do on a single stage press.

I (like njJoniGuy) make it a precision project on .223, .308, and 7mm rem mag. It is a relaxing hobby for me and my hand loads are more accurate than anything you can buy. If I want to go to the range and do some blasting I get some millsurp and toss the brass. Usually because its berdan primed

Ken

  • Author

Well looks like that Giraud trimmer is around $400. If it takes that level of equipment to do it in bulk I don't think reloading this caliber is for me.

 

Looks like I'll be feeding steel through my new toy.

Rcbs trimmer with 3-way cutter. Goes pretty quick even spinning the handle by yourself.

Well looks like that Giraud trimmer is around $400. If it takes that level of equipment to do it in bulk I don't think reloading this caliber is for me.

 

Looks like I'll be feeding steel through my new toy.

 

I have an old LE Wilson trimmer powered by a cordless screw driver. You can make lots of stuff work

I handload for my AR when I'm looking for any kind of precision. Otherwise, I use Silver or Golden Bear cheapo ammo for plinking. They use zinc or brass plating instead of polymer/laquer coatings on the cases.

 

When shooting my .223 handloads, I use a brass catcher. Sure beats chasing them around on the floor, and having them stepped or damaged in the process.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Recently Browsing 0

  • No registered users viewing this page.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.