Skip to content
View in the app

A better way to browse. Learn more.

New Jersey Gun Forums

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Winchester 30-30 lever action rifle restoration?

Featured Replies

My dad gave my his father's 30-30 Winchester lever action rifle. He doesn't recall firing it since he was a kid. Figures it must be roughly 70 years old. His father used to use it for deer hunting. He thinks the firing pin is bad and it wont fire. I'd like to find someone who could test/repair/restore it. Any suggestions on who to reach out to? Ideally I'd like someone in Central NJ who can handle an heirloom. I don't think it has a serial number on it so I don't know how to register it in NJ. He just gave it to me. Is it necessary to register it if I have a valid FID?

I think you might have forgotten that you did fill our a COE and gave him a copy, because otherwise it might have been an illegal transfer. As far as registering, it's voluntary in NJ, so why would you do that?

To my knowledge it is not necessary to register it. This is one of the arguments with this stupid proposed "universal background check", that even if you hand down a firearm to a relative you will still need to get a background check.

 

Also, if it is a Winchester and it is only 70 years old, there should be a serial number.

 

It is located in front of the chamber and often also stamped on other major parts that can be discovered upon field stripping your firearm. Sometimes old or refurbished firearms will have different serial numbers on different parts. An older weapon with matching serial numbers throughout will be more valuable than firearm rebuilt with parts from different firearms.

  • Author

Thanks for the tips how to date it. Looks like its a Winchester model 1894 made in 1926 according to the serial number. So its 87 years old. My grandfather must have bought this well before my dad was born. Pretty cool. So any recommendations on who I can trust to restore this?

Fix it yes you should, as far as the bluing and wood go restore it you should not.

I would also keep any parts that you may need to replace however it may need nothng more then a complete break down

and cleaning and oiling.

 

That's where you should start in my opinion.

What kind of shape is it in? I would just repair it as restoring an old gun destroys the value. For example, I have a GI 1911 that was restored. If it had been left with its original finish it would be worth $2500-3000. As its restored I'd be lucky to get $800. Collectors love that patina natural aging brings about.

  • Author

Its in okay shape. There is rust pitting on the barrel and butt metal piece, Couple small bits of wood chips missing from the stock. Nothing crazy. I don't think the rust is going anywhere. Its been below my dads basement steps for the past 42 years that I know about in a fabric case. Definitely needs to be cleaned and lubed. Should I get someone to get rid of the rust? I plan on shooting this and passing it on to my son some day. I don't plan on selling it. I consider it an heirloom.. so sanding the barrel to get rid of the rust and rebluing wouldn't destroy it in my opinion.. more protect it for future generations. I'd probably keep the rest as original as possible.

It's most likely surface rust, get youself one or two of these http://www.big45metalcleaner.com/

put some basic 3 in one oil on the rust and use the big 45 metal cleaner on it, it will remove the rest and wont dull or

take the bluing off on or around it. Steel wool any grit 000, 0000 will dull and remove the finish from the gun. Once it's

removed do not reblue unless it's down to the white. If you can post some pictures of the trouble areas so we know what

we are dealing with.

 

The stock most likly can be cleaned then stock wax like Tom's 1/3 mix can be used to give it some healthy moisture

and add a nice protective layer to it.

Over all it's not too bad the worst part is the butt plate. If it were mine I would do exactly as I stated above and no more.

I definatly would not take any kind of steel wool, or wire wheel to it, Use the bigbore 45 cleaner along with the 3 in 1 oil and

a lot of elbow grease and she will clean up nicely.

 

The stock I would clean down with some mineral spirits and then give it a coat or 3 of the toms 1/3 mix wax.

once your all completed with the rust and clean up oil her down then get a silicone cloth and rub it all into the metal and wood.

Do that a few times a week just with the silicone cloth for a couple weeks and it will look real nice. You have an excellent rifle

take care of her and may she bring you and your son another 100 years of fun.

I think if were mine I would try to contact the American Rifleman magazine and ask their opinion as to weather you should refinish or not and the rifles worth in it's present condition as opposed to you refinishing, or even cleaning it up. I would also try http://www.winchestercollector.org and see if they can help. I understand you would like to clean it up for your kids and future generations, but also think what it might be worth in the future if you didn't refinish it. In most cases, even though the gun might have some surface rust, it could be worth substantially more untouched. There are places that can professionally refinish antique firearms (namely Winchesters) and they will be worth almost as much. I would seriously consider all of the options first!

  • Author

I asked some advice on the winchester collector forum Hare trigger mentioned.(Thanks).

 

I got it all cleaned up really nice. No more rust, wood was cleaned and waxed, barrel

and everything metal was cleaned and oiled. Used 0000 wool with oil on the barrel. Took the rust

right off without destroying the blueing.

 

Now I'll take this over to the gunsmith subforum to find someone who can work on it for me.

 

Thanks Everyone!

 

http://s1286.photobucket.com/user/malice959/library/1926%20Winchester%201894%2030-30?sort=3&page=1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Recently Browsing 0

  • No registered users viewing this page.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.