Skip to content
View in the app

A better way to browse. Learn more.

New Jersey Gun Forums

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

So what sights is everyone putting on their revolvers?

Featured Replies

See question above... I'm looking for some new sights for my 686. I really want the hiviz TFO sights but they don't make them for my platform. 2nd choice was the express big dot system which seems to be the only tritium option. I'd like to have night sights but will look into fiber optics or what anyone suggests.

 

Patrick

 

 

This signature exceeds the 15 character capacity

I put SDM Fabrication sights on all my iron sight revolvers (green fiber)

 

They make both a pinned and dx version

  • Author

I put SDM Fabrication sights on all my iron sight revolvers (green fiber)

 

They make both a pinned and dx version

I'll look them up. If it matters these are for my hd/sd weapon

 

 

This signature exceeds the 15 character capacity

TFO sights are made by TruGlo, not HiViz. Moot point since they don't make any revolver sights.

 

In my opinion, fiber optic sights are terrific for competition - not so much for home defense. They rely on ambient light conditions to be effective. Tritium sights do offer some assistance in night shooting (HD), but you still have to be able to see the rear sight and the target. If you decide to go the tritium route, use a tritium front blade of standard size, as opposed to Big Dots. Big Dot sights are usually sold as a set (frt & rear) with the rear sight being a shallow V blade. Quick pick-up, maybe, but makes the gun useless for anything much beyond point & shoot range. Dawson makes tritium sight front blades in several widths. If your stock sights work for you visually, then use a standard width front blade (.125"). If you want faster pick-up with less precision, select a narrower front sight blade, like .100".

 

A nice large flat rear target sight gives a great sight picture, but it's hard to beat the stock S&W sight for a HD revolver. I use two different rear sight set-ups on my competition guns, but for HD I think the stock sight is a great set-up. Only thing that may be better is a Bowen rough country rear sight

 

Back to the front sight - S&W uses three types of front sights. 1) DX or Classic - these are user changeable and have a dovetail base that fits into the sight base and are held in place by spring tension. 2) Pinned in - the blade is inserted in a slot milled into the sight base and a solid through-pin is inserted. 3) Integral - rib, sight base and blade are monolithic. These cannot be changed without considerable milling and installation of a new sight base that accepts removable blades (DX type). Yours, being a 686, are most likely pinned in. Changing these is a little more complicated than it appears. The new blades will come not drilled, so after you drive out the original pin (tight interference fit), you have to hold the new sight blade in place while drilling through the existing holes in the sight base - alignment is everything because you are going in one hole, through the new blade, and then it is imperative that you hit the existing hole on the other side of the sight blade. A fixture and a drill press are what's needed.

 

Truth be told, you may already have the best sight set-up for your intended purpose. Save your money and practice using a flashlight. IDPA often times has low-light or no light stages where a flashlight must be used. I'd get a little more familiar with your revolver in practical scenarios so that you can learn what works best for you.

 

JMHO

 

Adios,

 

Pizza Bob

  • Author

Well I've decided already I don't like the front sight as the red gets lost on targets for me. Besides that it's fine. If I can spend $30 and get a green fiber optic then that looks like what I'm going to do. As a side note I'm taking a gun smithing class and installing a sight would be a fun project

 

 

This signature exceeds the 15 character capacity

Well I've decided already I don't like the front sight as the red gets lost on targets for me. Besides that it's fine. If I can spend $30 and get a green fiber optic then that looks like what I'm going to do. As a side note I'm taking a gun smithing class and installing a sight would be a fun project

 

 

This signature exceeds the 15 character capacity

 

easy to install, you'll need a drill press and the properly sized punches and drill bits. 

  • Author

Works for me. I'm ordering punches and such for the "kit" I'm assembling

 

 

This signature exceeds the 15 character capacity

you'll also need #54 drill bits, order a bunch of them, they are super small and break easily. 

file down the front sight and use an eagle eye on a bracelet made by the native americans like lightning jack

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Recently Browsing 0

  • No registered users viewing this page.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.