Skip to content
View in the app

A better way to browse. Learn more.

New Jersey Gun Forums

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

any HVAC guys deal with waste oil heaters?

Featured Replies

 title says it.

 

 i have a firelake horizon model 150 waste oil heater. it's giving me fits this year. she'll run all day long without a problem. when i turn the stat down for the night(right now i only turn it down to 50), i'll come in in the morning, and find that the flame sensor circuit breaker popped. i climb up, hit it, and watch the flame. usually it's on/off/on/off. there is no air in the system. pressures are good on oil and air. it seems as if it's always either the ignitors or the nozzle.

 if the ignitors, i generally open up the door, find them soaked(kinda like a flooded engine), so i clean them off, close it, then re-light, and everything's fine for the day. if it's the nozzle, i pull the entire injector bar out, pop the nozzle off, blow air through it, put it back in, bleed the system, and she's good for the day.

 

 this is EVERY $%^%$# morning this year. i've had it since about 2009 or 2010. it was 4 or 5 years old when i bought it. never had a problem with it till now, and i can't for the life of me figure out what the hell's going on. it's pissing me off, 'cause 1) it's friggin cold in the am, and 2) this is a stupid simple setup, yet i can't figure it out.

 title says it.

 

 i have a firelake horizon model 150 waste oil heater. it's giving me fits this year. she'll run all day long without a problem. when i turn the stat down for the night(right now i only turn it down to 50), i'll come in in the morning, and find that the flame sensor circuit breaker popped. i climb up, hit it, and watch the flame. usually it's on/off/on/off. there is no air in the system. pressures are good on oil and air. it seems as if it's always either the ignitors or the nozzle.

 if the ignitors, i generally open up the door, find them soaked(kinda like a flooded engine), so i clean them off, close it, then re-light, and everything's fine for the day. if it's the nozzle, i pull the entire injector bar out, pop the nozzle off, blow air through it, put it back in, bleed the system, and she's good for the day.

 

 this is EVERY $%^%$# morning this year. i've had it since about 2009 or 2010. it was 4 or 5 years old when i bought it. never had a problem with it till now, and i can't for the life of me figure out what the hell's going on. it's pissing me off, 'cause 1) it's friggin cold in the am, and 2) this is a stupid simple setup, yet i can't figure it out.

 

We had a similar problem with our lead re-melter.  Turns out it had a heating element electrode that pre-heated the bio oil it used.   The element wasn't getting up to temp and therefore the oil was more slurry than flow and with insufficient oil flow to the burner, it'd puke oil all over itself and not ignite.   Clean it, it'd start and off to the races till the next time we needed it.    The MSC tech replaced the element and it never had a problem again. 

  • Author

We had a similar problem with our lead re-melter.  Turns out it had a heating element electrode that pre-heated the bio oil it used.   The element wasn't getting up to temp and therefore the oil was more slurry than flow and with insufficient oil flow to the burner, it'd puke oil all over itself and not ignite.   Clean it, it'd start and off to the races till the next time we needed it.    The MSC tech replaced the element and it never had a problem again. 

hhmm......i hadn't thought of that. it felt hot when i'd take it out.....but i dunno how hot it was/is getting, nor do i know how hot it's supposed to be.

 

 i used to have garage equipment right from glendora come out to work on it when it got beyond basics....but i had a problem just over 2 years ago(turned out to be a sooted up flame sensor) that i'd called them about. they were supposed to call me back. they still haven't, and accordingly, they get no more of my money for anything at all.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Recently Browsing 0

  • No registered users viewing this page.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.