Everything posted by raz-0
-
Take a photo with Santa!
If they are unloaded? The toddler could drop a very expensive conglomeration of parts on the ground and ding them up.
-
First AR build complete
Main thing to be concerned about is if you are shooting weak ammo, extra friction on the BCG may cause short stroking.
-
USPSA @ Old Bridge 11/27/11
Maks, you need your b card. You need to work on getting your As. Your times are fine, you could actually slow down a tad. But you are dropping too many points.
-
wolf variable power recoil springs.
Yes, I have wolf 15lb progressive springs in two guns, and a 14lb progressive ismi in another.
-
Lower parts kit and question about optics
Gearhog had a $30 joebob coupon code for $15 and decent prices on LPKs. Dunno if still available. If you want to scope your upper you can use high rings, especially if you only plan to shoot it form sitting at a bench. If you want to be able to shoot it off hand with a nose to charging handle cheek weld, you will need something that puts the scope WAY forward. Larue SPR-E, and american defense recon-x mounts are my preffered mounts. Good, but expensive. Cheaper alternatives are something like the burris P.E.P.R mount. but it is not QD. If you already have some medium rings sitting around, a yhm 6" rail extension added to them will get you all the eye relief you might need for a nose to charging handle cheek weld.
-
Does same power factor with different calibers = same feel?
same power factor does not equate to the same feel for the recoil. That isn't to say that you can't Get a minor .40 to feel like a minor loaded 9mm. Load 165gr 40 to about a 130pf, and it will feel a lot like a 124gr 9mm loaded to 135-ish pf, but with less sight movement than the 9mm. It will also put down steel plates better. It'll also cost more to load.
-
OBRPC USPSA for December - Last Sunday is Xmas
Never an ob outdoor match in December due to the holiday.
-
How to Pattern Your Shotgun (and why your choke may be lying)
Nice write up.
-
USPSA @ Old Bridge 11/27/11
Grr. One less brain fart and I would have won l-10. Got a 74.9something on the classifier which pushes off a 71%, so that was good.
- cool site
-
Do manufacturers stand behind ammo?
Your best bet is to call federal.
- cool site
-
Ugh... Time for another ar15... Simple question regarding needed parts..
You'd be limited in choices depending on how much work you were willing to go through. If you cna get a barrel nut over the muzzle device and shaved down front sight, you could install almost anything. If you can't, you are limited to options that mount on a stock AR barrel nut. One of the more affordable is this one -> http://www.rainierarms.com/?page=shop/detail&product_id=2563 With that, you'd take the dremel to the front sight tower, clamp the heat sink/barrel nut thingie to your barrel nut, slide the tube over and clamp it down.
-
steel plate supplier
I was shooting mine with 10" spikes without any issue other than it being low to the ground.
-
steel plate supplier
IMO the best bang for the buck are bunker hill self resetting targets. 3/8 ar 500, $86 shipped (if you order two, they discount as they fit in the same flat rate box as one does) http://bhsenergy.com/steeltargets.html
-
Ugh... Time for another ar15... Simple question regarding needed parts..
Well it is a 14.5, so the muzzle device is welded. There are only a couple rail systems that will fit over the front sight without removing it. At least if you want a free float rail system. If not, they sell rail segments for the moe handguard.
-
Delta Percision bullets..
Thebulletworks.net has good prices on nice plated bullets.
-
Idea for a New Board
You didn't know New balance was made in the USA because they aren't. They held out for a LONG time relative to the industry, but most of there stuff is not made here. What is made here is only assembled here, and you'll see that noted on their website They do have some new joint project military boots, and a couple of those say made in the USA. They might be more domestic if any of them are Barry compliant.
-
How many rounds can you load per hour?
It's the size of the components. .45 is like duplo, 40 is like Lego, and 9 is like Lego technics... Small and fiddly. On top of that, with .45 you only really have to deal with crimped primer pockets. With 9 you have that plus 9x21, 9x23, 38 super and supercomp, 9x18 and .380 all easily sneaking in and screwing things up.
-
Ugh... Time for another ar15... Simple question regarding needed parts..
Aim surplus has 10% off for black Friday, bring the spikes 14.5 with dynacomp to about $500.
-
How many rounds can you load per hour?
9mm slows me down, .45 is the fastest. .40 is somewhere in the middle. For 45 I could do 100 an hour on my lee turret using batch deprime/resize and hand prime, then load the rest of it normal. On the lnl ap, I could get 450 per hour.
-
Ugh... Time for another ar15... Simple question regarding needed parts..
Most of the ones I listed are going to run $600-800 for their basic upper decent 14.5" Del-ton will build you an ok 16" upper for less, but it is pretty basic with a mossberg barrel. They'll even weld on the muzzle device if that is necessary.
-
Ugh... Time for another ar15... Simple question regarding needed parts..
Like I said. Rainier arms lists their uppers as well as some 3rd party ones. Noveske sells theirs, spikes sells theirs, Lauru sells theirs. I could list a ton, but if you are looking for a quality pre assembled 14.5" upper, those are where I'd go besides bravo. Are you looking for something particular?
-
Ugh... Time for another ar15... Simple question regarding needed parts..
The carbine gas system is shorter than the midlength or rifle. It increases the gas pressure transmitted to the BCG a whole LOT. The gas system was designed for a 20" barrel with a rifle length gas tube, which results in about 19k psi. A carbine length system on a 16" barrel results in about 33k psi. A midlength results in about 26k. Those numbers are pressure at the gas port IIRC. The higher pressure means more stress on the locking lugs on the bolt. It also means the BCG slams back with a lot more force, which results in harsher recoil. If it slams hard enough, you amy also get the BCG slamming into battery which can cause the muzzle to dip. Worst case, you can get slam fire form the firing pin bouncing, but usually you have to be really over gassed for that, or you have to have crud in your firing pin channel. If you are considering a supressor, then that makes the pressures jump even higher, and that's where things like adjustable gas blocks and the noveske switchblock come into play. Especially when dealing with shorter gas systems. IMO you want the longest gas system that is reliable for the barrel length you are going to use. Several other factors come into play, but in general, for 14.5 or 16" go midlength. For 17" or longer, go rifle. Rainier arms builds uppers, as does noveske, spikes, etc.
-
25 "Must Have" Guns in a "Proper" Collection
25 is a bit of overkill. 1) pump shotgun. 2) semi auto shotgun 3) an evil black rifle (center fire) 4) a decent bolt action rifle (center fire) 5) A decent semi auto pistol (center fire) 6) A decent revolver (center fire) 7) a rimfire pistol 8) a rimfire rifle. 9) a pocket gun (centerfire) Choose those wisely, and you can shoot a TON of competitions, and be familiar with most firearms enough to figure out ones you haven't met before fairly quickly. That's a well rounded collection. I'm not saying I've stuck to that list or completed it yet, but it's a pretty solid base.