Everything posted by Pizza Bob
-
What's your favorite in .40 S&W?
Not to beat a dead horse (but I will - what happened to the plethora of smilies BTW) in regrad to using rimless cases in revolvers - even without the external mechanism (moon clip or springs in the extractor) a round would not "fall through" the cylinder. Cylinders are bored with a shoulder that corresponds to the case mouth - so they should/will headspace on that shoulder provided the case is the right length. That shoulder's function, however, is not headspacing. It is there so the cylinder throats are closer to bullet diameter for better accuracy. With a cylinder throat closer to the diameter of the body of the cartridge, the bullet may "tip" upon exiting the case, resulting in it going into the forcing cone tipped. It would also obdurate to the larger dimension of the oversized throat and then be swaged back down in the forcing cone - possibly with the bullet non-concentric to the cone. This is a fancy way of saying your accuracy would be crap and there'd be good possibility of keyholeing. I speak from first-hand experience, having once owned a S&W that did exactly that. Now that I've written the above, I'm curious if the Taurus Judge has a shouldered cylinder. Not sure that it could, unless the diameter of a .410 shot shell is under normal throat diameter for the .45 Colt. Anybody have one they could check? Too much time on my hands. Adios, Pizza Bob
-
Alliant bluedot safety notice.
Tony: Since this thread was stickied, I think that you should either delete my post about 16.5 grs of Blue Dot behind a 240 gr bullet in .44 Mag (that appears in the current stickied thread), or ad this post... http://njgunforums.com/forum/index.php?/topic/12766-use-current-loading-data/page__p__168927__hl__%2Bblue+%2Bdot__fromsearch__1#entry168927 ...which I made after assessing available current data. Just a suggestion. Adios, Pizza Bob
-
What's your favorite 9mm?
How about a .40 S&W? http://www.ombexpress.com/c_0/p_UG136.aspx
-
What's your favorite in .40 S&W?
OK, I'll handle these, one at a time. Radek may have confused the issue somewhat, with semantics. In order to be a rimmed cartridge the "rim" must protrude beyond the body of the case. Which he stated correctly. When he referred to S/A cases as also being rimmed is where he went off-track. What he really was referring to was the extractor groove. Rimmed cartridges are generally used in revolvers and they headspace on the rim. In a revolver, in the absence of rim, it must headspace on something external to the cartridge itself. In most cases this is done by inserting the cartridge, via the extractor groove, into a thin metal clip that holds multiple cartridges, and placing them in the cylinder en bloc. This will give you a better idea what I'm talking about... In a semi-auto pistol a rimless cartridge theoretically headspaces on the case mouth (which is why they should be taper-crimped, not roll-crimped, for you neophyte reloaders out there). I say theoretically because in most cases they are actually headspacing on the extractor. The Charter Arms picture, to which you linked, uses a slightly different system. Rather than use an external device (moon clip) they use a spring arrangement in the extractor star. It takes slight pressure to push the cartridge past the spring when loading and it expands into the extractor groove - thus holding it at the proper depth to headspace on the extractor groove. CA has yet to release the guns using this system. Rumor has it that they are tied-up in court over patent rights, as I believe that S&W used this system on a 9mm revolver that is no longer manufactured. OK, as to .357 Sig - First, they cannot just use the .357 magnum round in an auto pistol because it is a rimmed cartridge (meant for revolvers) and it is very long, making for a very rotund grip, not easily handled by people with normal sized or small hands. Now before everybody jumps on me, yes, I am aware of the Coonan Arms .357 1911, as well as other semi-autos that use rimmed cartridges - but they have proven problematic in a commercially viable SD firearm. The most successful one, was, of course, the S&W model 52, which shot low-powered .38 spl wadcutters for the bullseye game, not a viable SD arm. The .357 Sig was an attempt (a good one) to duplicate the ballistics of the .357 Mag in a semi-auto cartridge. Because of the very short neck, it is not recommended that anyone attempt to make .357 Sig cartridges by necking down .40 S&W cases. The share case head dimensions, but if you blew a .357 Sig cartridge out to .40 diameter full-length, you'd find the case to be longer than a real .40 S&W. The use of the short cartridge made for a manageable grip size and allowed double stack magazines to be used (something that is also problematic with a rimmed case in a S/A), thus increasing capacity - not diminishing it. The use of the smaller diameter bullet in a large diameter case, allows for more powder capacity driving the bullet faster. This is achieved by making the case a bottlenecked case. This makes it a PITA for reloaders (especially with the short neck), but we are talking primarily a defensive round here - I won't reload my .357 Sigs - too much hassle. The bottleneck case aids in more reliable feeding than a straght-wall case, in a S/A. The smaller diameter bullet end of the cartridge is starting into a large hole (to accomodate the head of the case) in the chamber, thus less chance of hanging up. There are many LE agencies, around the country, that have come to the conclusion that the .357 Sig is one of the finest defensive rounds out there. Good stopping power, good for shooting a barricaded suspect without too much worry of overpenetration. It is a cartridge that makes emminent sense for its, admittedly, narrow purpose of self-defense. Off my soap box now. Thanks for reading. BTW, welcome to the forum. Adios, Pizza Bob
-
Post Your Tactical Shotgun Pics
I'll play. Bennelli SuperNova with +2 mag extension and a Streamlight TLR-1 light with pressure switch...
-
What's your favorite 9mm?
I don't know if I'd term this my favorite - I just think it has a very high "cool factor" - as my friend calls it, "It's like jewelry for your pocket." Kahr MK9 Adios, Pizza Bob
-
Looking for a side of pork...
This is about 2 miles from my house. Not sure if they sell whole or half carcasses, but it would be worth a phone call. http://www.elyfarmproducts.com/ Good luck. Adios, Pizza Bob
-
USPSA @ Old Bridge 9/26
Polymer? Uncovered? Absolutely!
-
Hollow Point/Home Defense Ammo Preferences
Ammo design and function have come a long way in the last 10 to 15 years. Pick something from one of the major manufacturers, that works 100% in your gun and go with it. I do see a trend in defensive ammo that adheres to the light bullet/high velocity philosophy. I'm not a fan of that school of thought - not criticizing those that are, just be aware that anything beyond SD distances (>10 yards) your gun may not shoot to point of aim. With lighter bullets moving faster it will shoot lower than where must SD guns with fixed sights are regulated. Manufacturers tend to regulate their sights at 25 yards with the most common bullet weight per caliber. That means most .45 ACP's sights are regulated with 230 gr bullets. 9mm with 124 or 147 gr bullets. Most .40 S&W's with 180 gr bullets. When you go to a lighter, faster bullet there is less dwell time in the barrel, which means a lighter/faster projectile will exit the barrel very early in the recoil arc. A heavier/slower bullet later in the arc, thus printing higher on the target. EFMJ's were mentioned - they are tough to find in any iteration, but you should be aware that there are heavier EFMJ's made by Federal than what you commonly see offered to the public. For instance, you commonly see a 165 gr .45 ACP in EFMJ (in the small 20 rd boxes), but they also make them in 200 gr - and these are boxed 50 to a carton. Same with .40 S&W. In the 20 round boxes you get 135 gr bullets. In the 50 round boxes you can get 165 gr bullets. And in 9mm it is 105 gr vs. 124 gr. The heavier bullets in the 50 round boxes are marketed as LE only, but are available to the public. I've had luck finding them at gun shows, but I believe that all EFMJ's are in short supply right now. I also tend to favor Speer Gold Dots in all calibers, but especially in .357 Sig. This ammo has been tested extensively by the various LE agencies that use the .357 Sig round and has been chosen over everything else (SS, Sky Marshals, RISP, TDPS et al). I also like their short barrel loads, especially for the J-frame snubbies, And their 230 gr .45 ACP at regular pressures. It's hard to make a mistake, as long as you stick to mainstream manufacturers and some of the specialty guys are good too (like Corbon). Stay away from marketing hype like "Extreme Shock". Test what you will carry in the weapon in which it will be used. That is all. Adios, Pizza Bob
-
USPSA @ Old Bridge 9/26
I don't want anyone to think I'm promoting a particular product because it's beneficial to me - I have no association with any of these products. That being said - one of the biggest hurdles to getting involved in this type of shooting is the cost of equipment. So here are some suggestions for low-bucks, but very functional equipment. Belt - You need a good gun belt to support that holster & gun as well as the number of mag pouches you'll need. Uncle Mikes makes a polymer reinforced, 1.5" wilderness-type belt that sells for about $25. I think I got mine at Natchez Shooters Supply, but anyone that carries Uncle Mikes products should be able to get it. Mine is holding up fine after about 4 or 5 years of use. Holster - even the kydex holsters like Blade-Tech are not cheap. If you are trying this out and need a holster to see if you like it, try a Fobus holster. Polymer means the gun comes out slick. Pick one up on Ebay for $20 - $25 bucks. Mag Pouches - This was always a sticking point, these are not cheap - however, I found a guy who will do kydex mag holders 3 for $30 plus $5 shipping. He already has patterns for a number of different guns. If he doesn't have one for yours, if you're willing to surrender a mag for a little while (returned with your order) he can make them for you. There are competition and CCW versions, plus if your thinking of shooting IDPA as well as USPSA, let him know so he can make the mag holders compliant. His name is Chris Buell and his e-mail is: [email protected] Here's a thread by him/about him on Sig Forum... http://sigforum.com/eve/forums/a/tpc/f/350601935/m/145103562/p/1 Now you have no excuses. Enjoy. Adios, Pizza Bob
-
Valley Forge Gun Show - Sept 17-19
This show officially opens on Friday at 4 PM - and that's when I'm going to attempt to be there. Meeting up with a bud from Philly, so it depends on when he can get away - but he's trying for an early start. I've always gone on Sat in the past, but my buddy has done the Friday deal and likes it - less crowded, better selection of merchandise. Be aware that it is $15 on Friday and $9 for Sat or Sun. Attached to this post is a coupon for $1 off - guess it's legit, came to me by way of a friend, so I'll pay it forward. Coupon1.doc Adios, Pizza Bob
-
USPSA @ Old Bridge 9/26
Have to check my social calendar, but if the sun is shining, I'll try to make this one. Adios, Pizza Bob
-
What's your favorite in .40 S&W?
Need you ask? Recently acquired S&W 646 - the best DA I've ever felt on a S&W revolver. It's a sweetheart. Adios, Pizza Bob
-
Dick's Sporting Goods Deals - 9/12-9/18
If you are talking about VF - why not attaend the show on Friday 09/17 (a bit more expensive - but first pick and less crowded) or Saturday 09/18? I'm heading over Friday afternoon.
-
Thinking about a 1911
You shot it at BA - It is an alloy Officer's Model frame with a Commander top end... Does this ring a bell? Adios, Pizza Bob
-
Thinking about a 1911
I've said this before, on here, but I'm always at a loss as to why people want a Commander size 1911, or a "Carry" model in the Sig P220 or 1911. Unless you say, "I just like the way it looks." I can think of no practical reason. The grip frames of both the Commander and full-size 1911 are the same length - likewise the P220 and Carry versions. It's not real difficult to hide an additional 3/4" of barrel length and the advantages are a longer sight radius and higher velocities. Even if you bobtail the Commander for better concealment - why not do the same thing to the full-size. OK, rant over, back on topic. Bry@n, I think the Sig 1911's are some of the most underrated 1911's available. They got off to a rocky start and the rep kinda stuck with them. Current production Sig 1911's are great guns. I really liked the TTT, but they are no longer making that. The STX is run through the Custom Shop and there is some handfitting. I would also imagine the street price would be less than the S&W Pro series. I like the S&W 1911's also so I think it should come down to what model you like the best from either of those manufacturers. I carry a Sig 1911 RCS (lightweight compact) - Maks has shot that and commented favorably on it - just as I have his Pro-1911 9mm. Bring home the one you like best (even if it's a Commander....sigh). Adios, Pizza Bob
-
Valley Forge Gun Show - Sept 17-19
Depends on my friend - as close to opening (4 PM) as we can.
-
What kind of optic
Hey Parker - I used to have one of those: But mine was left-handed, and I'm not (it was my fathers - he was). Recently sold it to fund this... Weren't the rimfire scopes (like what's on my 581) 3/4"? As I recall they were markedly smaller than a standard 1" scope. I too have a couple old Weaver K4's floating around - one loose and one on a sporterized 1917 Enfield. Babaganoosh, if you need any help, we are only as far away as your keyboard. Adios, Pizza Bob
-
Valley Forge Gun Show - Sept 17-19
I intend to go Friday - a first for me. Meeting up with a friend from Philly. Anybody that wants to ride along on Friday (Early bird and all that...) you're welcome, just PM me. Adios, Pizza Bob
-
Inexpensive AR 22 Mount for a Red Dot
How can you remember that many guns ago?
-
Inexpensive AR 22 Mount for a Red Dot
Chris: Check out some of the air soft accessory places. Risers with thumb-screws (as opposed to QD levers) can be had for under $20. Should be fine for rimfire applications. Adios, Pizza Bob
-
How old for Pistol Permit
Federal law = 21 to purchase / 18 to possess Currently being fought by the NRA - lawsuit to make it legal for 18 YO's to purchase
-
What kind of optic
That's a standard rimfire 3/8" dovetail. If you decide to go with a scope, you can purchase rings that mount directly to the dovetail, eliminating the need for bases. For a red dot, it would depend on the mount - you may find that buying adapters and such to make it work is more costly than just mounting a rimfire scope. Good luck & have fun. Adios, Pizza Bob
-
Sig Sauer P226 e2
Tuckoo: I believe that you can save the money and hassle (not that more permits are a bad thing). I believe that you can convert your std P226 to the E2 configuration. I may be wrong, but I seem to remember reading that Sig was going to offer some kind of conversion kit with the main spring arrangement and grips. Not sure, so a call to Sig's customer service would be in order. Adios, Pizza Bob
-
Sig Sauer P226 e2
That's a velux blanket......spread out on a pool table :mrgreen: A Brunswick Gold Crown II.