Old School

These shotguns have notoriously rough chambers. Take a look, The roughness causes the hulls to stick prior to ejection. Not on all shells but on the cheap Walmart 100 pack Winchesters it is common. I don't want to make the recommendation to clean and polish the chamber but that is what I would do. also I would make sure the bolt face is clean and the extractor is sharp and not damaged. Note: everything I've written applies to the late model 870 Express that I've seen

I travel up to Albany to visit with the boat and really have a problem sleeping naked and defenseless. No BS...The Hudson is as gorgeous and any river in the world.

PM sent

Smokin .50. - who said I don't have a boat shotgun on hand already? I do. But I only use it for NY trips. Sent from my iPhone using Tapatalk

I've fired a 12ga one handed in an emergency. It's not bad adrenaline makes it doable. In close quarters 20-30 ft ( statistically 21 ft is a mean distance). I summer live on a boat, I could find this handy. I'm off the phone and back on a keyboard. if I need to eliminate a threat in close quarters this would be my go to. Just a wild ass guess is you will get a minimum of 1 1/4 - 1 1/2" pattern(spread) per yard. So in my 15 foot cabin I could expect a minimum 5" pattern so a threat coming through a 26-27" companion way is neutralized even with some error. Sent from my iPhone using Tapatalk

Agreed NJ banned. Why stupid?

Not necessary. blue painters tape both sides of catch and never scratched one.

I've got captive punches and role pin punches but I use slave punches for that stuff too. i'd rather just do the job.

where the hell are ya?

This Keep us posted

Gentlemen, Thank You!! I may take one of you up on your offer. I Just received an email from a manufacturer that may have some in a few weeks. They're about $100 but I need a 10 shot repeating bolt action. Thanks again!!!

Bump

Excellent resource. To the OP -- I have a metric thread gauge if you need to borrow one.

I need a magazine to take dimensions off of. I'm trying to adapt a 9 or 10 round mag to my Savage mod 12 243 Win. I will not molest your mag. Just need to measure, disassemble and reassemble. Thanks, Frank

Just follow Topher's link http://www.brownells.com/gunsmith-tools-supplies/rifle-tools/barrel-tools/ar-15-m16-barrel-extension-torque-tools-prod27452.aspx 080-000-637WB AR-15/M16 Barrel Extension Torque Tool $49.99

I show it IN stock at Brownell.

Bitch put the muzzle in her mouth. Very oral !!

Correct. Unless they put an "after this date" thing on it. Sent from my iPhone using Tapatalk

I predict you are going to see rifle caliber pistols become AOW

We kind of agree. Good point in uniting gun owners. My guess is that most modern center fire rifle cartridges will pierce soft body armor. Thus making any 2000fps rifle round a "cop killer"

So I lost the zero on my 24" AR got frustrated and left the range Sunday (It was sighted at 300 lost my notes for 100..Duh!) So went back today in the mud and just grabbed a few boxes of generic hand loads ( 55gr FMJ 25gr CFE223 Wolf primers) Just stuff that I ran through the Dillon. Here's the results. Don't know why I agonize with precision stuff when this was kicked out of the Dillon. !3 shots @ 100 and I have no idea where the hole in the upper left came from.

Relevant or or not I don't know. I run a few 24" ARs.. I would think the extended length would act much like a can. Most recent build has an .063" gas port at a rifle length position of course. One is at .080", It's the way I got it and runs fine. But I do run M16 bolts for the extra dwell time hoping to get a little extra velocity.

Yeah I wouldn't want to suppress a 24" barrel any way...LOL

This stuff sounds like a nightmare. I just hope my 6mm AR runs.

Contact member "T1Defense"