henrym

What are you looking to turn the trigger into. Thats a better place to start.

You must need alot of ky.

Steele 6000W generator - 1.16 quarts according to the spec http://www.samsclub....4780461.ip#spec As was stated in an earlier post, make sure to use a high quality oil. These machines will possibly be running for a long time. If possible, also replace the spark plug with a quality unit. Follow the manufacturer directions about the initial oil flush. Most are within the first 20 or so hours.

yes they do. Forward grip on a Pistol Makes it an AOW. Direct from ATF “Handgun” is defined under Federal law to mean, in part, a firearm which has a short stock and is designed to be held and fired by the use of a single hand… Gun Control Act of 1968, 18 U.S.C. § 921(a)(29). Under an implementing regulation of the National Firearms Act (NFA), 27 C.F.R. § 479.11, “pistol” is defined as: … a weapon originally designed, made, and intended to fire a projectile (bullet) from one or more barrels when held in one hand, and having (a) a chamber(s) as an integral part(s) of, or permanently aligned with, the bore(s); and (b) a short stock designed to be gripped by one hand and at an angle to and extending below the line of the bore(s). The NFA further defines the term “any other weapon” (AOW) in 26 U.S.C. § 5845(e) as: … any weapon or device capable of being concealed on the person from which a shot can be discharged through the energy of an explosive, a pistol or revolver having a barrel with a smooth bore designed or redesigned to fire a fixed shotgun shell, weapons with combination shotgun and rifle barrels 12 inches or more, less than 18 inches in length, from which only a single discharge can be made from either barrel without manual reloading, and shall include any such weapon which may be readily restored to fire. Such term shall not include a pistol or revolver having a rifled bore, or rifled bores, or weapons designed, made, or intended to be fired from the shoulder and not capable of firing fixed ammunition. ATF has long held that by installing a vertical fore grip on a handgun, the handgun is no longer designed to be held and fired by the use of a single hand. Therefore, if individuals install a vertical fore grip on a handgun, they are “making” a firearm requiring registration with ATF’s NFA Branch. Making an unregistered “AOW” is punishable by a fine and 10 years’ imprisonment. Additionally, possession of an unregistered “AOW” is also punishable by fine and 10 years’ imprisonment. To lawfully add a vertical fore grip to a handgun, a person must make an appropriate application on ATF Form 1 (5320.1), “Application to Make and Register a Firearm.” The applicant must submit the completed form, along with a fingerprint card bearing the applicant’s fingerprints; a photograph; and $200.00. The application will be reviewed by the NFA Branch. If the applicant is not prohibited from possessing a firearm under Federal, State, or local law, and possession of an “AOW” is not prohibited in the applicant’s State of residence, the form will be approved. Only then may the person add a vertical fore grip to the designated handgun. A person may also send the handgun to a person licensed to manufacture NFA weapons. The manufacturer will install the fore grip on the firearm and register the firearm on an ATF Form 2 (5320.2). The manufacturer can then transfer the firearm back to the individual on an ATF Form 4 (5320.4), which results in a $5.00 transfer tax. If the manufacturer is out of State, the NFA Branch will need a clarification letter submitted with the ATF Form 4 so that the NFA Branch Examiner will know the circumstances of the transfer. Questions can be directed to the NFA Branch or the Firearms Technology Branch.

In addition to what lunker said, post up what you are looking to buy. Many here are willing to let you shoot what ever they own before you make the decision to buy.

I make this decision day to day because to me it has more to do with the terrain ou plan to hunt. If its open and you have clear lanes out to 50/75 yards then sure take the slug gun. If you are pushing through more dense brush where you are hunting, the scoped slug gun may have any advantage over quality buckshot.

WD-40 is actually designed to do very well in this type of environment. The WD stands for Water Displacer.

Too bad we wont ever be able to own one as civilians 1 trigger pull with 2 bullets = NFA m.g. made post 86

Slip 2000 products is all I use, and a majority of what we stock. People are a little hesitant at first, but then they see the light

Ive met 2- both of whom carry LARGE amounts of cash as part of their daily business.

Im a Voodoo dealer at east brunswick sportsman, and am expecting these in this week.

Harry organized the group buy about 8 months ago?

Titegroup is funny with the way recoil compounds. Other powders are different

run about 500 rounds through it as a break in period. It makes a big difference

At my shop the markup is close to the lowest in the state. Our customers are great because for the most part they realize how razor thin the profit margin is. Their isn't a lot of money to be made on guns without completely pricing yourself out of the market. A huge problem is BUDS. People come in plainly telling you that they are going to buy the gun online but they want to handle it first. If people dont support their local shop, they wont have that privilege. BUDS is a horrible retailer. Besides the fact that they sell many, many guns below dealer cost, their customer service is horrific.

As far as I know frog lube is water based. Might be part of your problem.

In addition to the fact that glock no longer sells trigger bars alone. Now its the whole trigger assembly.

Problem being, loctite releases under heat, and ar barrels get hot. You're right.

as per glock, that bump as added to stiffen that portion of the trigger bar to remedy issues found in the gen 3. If you have access to an orange backplate to check firing pin lug engagement, check it. You might have some trigger bar cant without that bump.

give East Brunswick Supply a call. They have everything ever thought of in plumbing/hvac

Dropped paperwork for permits today and was told that I shouldn't bother applying for more than 3 because they will not be renewing permits in the future. Has anyone else had any experience with this?

check out some of the gun engravers who do slide work. They might be able to use the same laser engraving machine.

Otis makes great stuff

More Brass catchers!

A little more background It spetters under heavy braking, other than that it runs well. In december it got a tank of bad gas but that was supposedly resolved.