alec.mc

I'm especially bitter about long guns because i'm a righty, but a left eye dominant shooter. Thus, I need to shoulder all long guns as a lefty. Which sucks. But seriously. This should sum it up. Derp.

Shotguns are for guys that can't aim a pistol slug properly.

WE NEED STAGE DESIGNERS and VOLUNTEERS in the morning to help set up the match. draw something on a napkin, in microsoft paint, on the back of your hand , whatever and send it to Vlad. That being said, I should be able to make it on sunday vlad and setup a stage.

Black/Red = Hot ( 120 each, you get 240 with a voltmeter across the 2 ) White = Neutral Bare / Green = Ground

you wouldnt be able to install an interlock in that situation. I do the same thing, I have 60 amp 220v running from my main house panel out to my detached garage that has its own panel. I wired the generator outlet to the garage panel, in the event of a emergency situation I back feed generator power through my garage back to the main. Everybody here is acting like these scenarios will not work if you dont have an interlock switch, all an interlock does it make it absolutely dummy proof so that you can not physically have both breakers on at the same time. Just dont be a retard and turn the main back on while you are on gen. power.

Really ? I flew out of newark last week with a handgun, no issues. make sure its in a locked hardshell box declare your firearm put card in box they X-Ray the box to make sure it's not loaded. 10 minutes later your done.

User choice. I have a 4 speedloaders in my reloading block, only use one and pick up as I go.

I travel in and out of EWR newark airport a few times a year with handguns. I keep them in a hard shell plastic pelican case, with 2 locks on it, Inside of my checked duffle bag. That said, after reading the law, you could interpret it the exact way she read. Hopefully the case gets dropped if/when it goes to court and we could use this to loosen up some of the laws.

It's like watching the gun slinger crew shot in even more slow motion. Oye vey.

Bob knows all about light strikes, it's his favorite past time. It's likely just your main spring strain screw needing tightening, assuming it's all factory. Take your grips off, tighten the screw under there. Done.

You didn't tell me you were selling a 686 too ! ;-)

Beat Jim Norman. Trying to break into the top 5 at our locals with a minor pf revolver among the sea of major PF limited and open shooters is a challenge. Almost there, almost.

Will still beat Vlad.

Want.

LoL , that picture is pretty funny Nick. Vlad, no - I have no interest in watching a bunch of guys spend 3/4 of the stage trying to bumble in some shotgun reloads, and then the rest shooting ( missing ) a steel target at like 300 yards for like 6 minutes. I'd rather go to the dentist.

Meh

vlad, we still on for tomorrow? weather looks a little spotty.

From my experience the 100 yard is open during uspsa,,but we use the shotgun field for extra parking

I can understand the frustration for guys that do not want to do competition style shooting, yet want to go out for plinking on a sunday. Though, the club makes it abundantly clear at new member orientation that OBRPC is a club that is heavy into competition shooting, and that most the range is scheduled out to a league on certain days. It's sort of like the guy who buys a house next to a gun range, and then complains that there is noise of gunfire.

the ansac is taller, I'd call or email Bob @ the website, I'm not 100%. Also, if you plan on using it for static steel competitions, get the bigger case, each stage is 5 runs, so get the case with 10 clips loaded in it for 2 full stages.

If your going to do steel challenge with it, buy one Anzac loader and a 4wheelguns.com .22 cases and pick them up for each string. Best of luck

Bob covered it pretty well, The *level/quality* of speedloader will depend entirely on what you plan on using them for. If you plan on doing some plinking, or some steel challenge with it ( no reloads on the clock ) a case with some DS10 / Speed beez loaders will work fine, DS-10s are the original, and the speed beez are rip offs. That being said, they both work fine, though - the speed beez i've had starting falling apart of 2 years of heavy use. If you plan on doing reloads on the clock, the Ansac is the way to go, The thing is awesome, and loads really well. You can purchase all of this things, loaders, and cases for ammo and the loaders and belt rigs over at www.4wheelguns.com , tell Bob I sent you over. examples:

Something to note, The M9A1 has a fixed, non - interchangeable front sight.

What are you shooting? Limited division typically consists of heavy metal framed single action guns, shooting major power factor, with larger capacity magazines. This division also allows race type gear on belt, such as race holsters and mag pouches. Gun modifications are also allowed. Production division is typically made up of (stock like ) plastic da/sa or striker fired guns, such glocks, m&ps, XDs, and some metal da/sa guns. The Division only allows for shooting minor power factor ( usually 9mm is pretty popular ) The division also has restrictions on what type of holster and mag pouches you can use, and where they are located on your body. Also, production division doesn't really allow modifications to your gun ( though some trigger work and sights are fine )