Everything posted by T Bill
-
Opinions on PSA lowers?
Yes, they have a high shelf, PSA lowers as stated above are GTG. Blemished lowers on sale are GTG also. Your would be hard pressed to find it on most.
-
Somerset IDPA 9/21 - NJGF Well Represented
Ya smell, ya drool, you have two outta three, becareful!
-
Somerset IDPA 9/21 - NJGF Well Represented
Every thing in life smells. It's the ones that stink you worry about.
-
Tanners in PA. Pallet of 22 $21.99 for 325
Auto Match was always sold in 325 bulk packs.
-
Do powder and primers go bad
Bullseye shooters would down load rounds for matches. Done it myself. In fact I still have some loaded in the early nineties. They will not work with a 1911 with factory standard spring (16LB). We would cut down a 1911 spring until it would cycle reliably or install reduced power springs (5LB and up) from Wolff Spring. Typical standard Bullseye load with Bullseye powder and a 200 LSWC would be 3.5 grains. Some would load as low as 3.3 if they could get all the variables on target. I'm sure they would work fine with reduced power springs.
-
OBRAMS Action Rimfire - Sept 20th, OBRPC
Welcome aboard Howard. See you tomorrow!
-
Inherited reloading equipment.. Nowhere to start.
While Dunks normally have a decent selection (mostly one pounders of rifle lately) either at the Stroudsburg or West End stores prices are up there. Not many places in the Poke in the nose to pick it up. T&T near Easton has better prices but you have to be sure he's in. He's open Saturdays if he's not at a show or Monday-Wednesdays evenings. Otherwise you travel out towards Cabelas (Shylas or Trop) or hit up the bigger Eagle Arms gun shows (Greater Phila or Split Rock).
-
Help me pick a good upper.
Aero Precision already coated in your choice of 10 or so colors stripped $105.00.
-
Target AR15 build
Ditto ^^^^^^^^^^^^^^
-
Help me pick a good upper.
Most any major manufacturer sells good plain jane stripped uppers. I have used Colts, RRA, PSA, Spikes, et al. I have even used blem PSAs without trouble. All forged ones are about the same. If looking for one see MidwestPX, Ty is a vendor here and sells tried and true parts at decent prices with fast shipping.
-
55 g or 62 g for my AR15 ?
For paper punching my vote would be 55's. Works well with 7 or 9 twist.
-
ATI Cavalry O/U Shotguns
Given the budget and such, I would seriously look at Stoeger (owned by Beretta), BIL has both a Stoeger Condor and a Fausti and with a little tweaking (he had them back bored and Magnaported), turned into great clays and field guns. Don't like the Mossberg, in fact I have a 12/20 Combo here now that has to go back for trigger work again! Don't see CZ on the course at all. Do not know why. Thirty inch barrels are preferred for Trap and Sporting Clays, but may be a little long for upland game along with the weight. So maybe compromise may need to rule the day. I have upland gamed with my 30" RRL a little hard to swing fast on short shots. The Winnie 1200 24" 20 fills that niche. Not a waterfowler so nothing to help you there.
-
Switching compensators
www.adcofirearms.com is a gunsmith in Sylvannia, Ohio know for his work on AR type firearms. Reasonably priced with fast turnaround. High quality work with very professional attitude. Used by many. Nick is correct here also, and ADCO will only remove comps not silver soldered. A qualified answer would require more info. Manufacturer, barrel type and age, number of rounds down the pipe, any knowledge of how comp was attached, etc.
-
Inherited reloading equipment.. Nowhere to start.
To get started just can a can of Hornady Case Lube, spray it on per instruction and go at it. I will give you a formula for lanolin and alcohol that can't be beat but takes a bit of getting used to. A hick in the learning curve you don't need now. The formula is: A solution of 1 part pure liquid lanolin and 4 to 5 parts parts 99 percent isopropyl alcohol (4 oz of liquid lanolin to16 - 20 oz of isopropyl) works well. When mixing you may find that the lanolin mixes better if you warm both the alcohol and lanolin in a bath of warm water to about 105 - 110 degrees F before mixing. DO NOT WARM EITHER OF THEM OVER AN OPEN FLAME! Once the solutions are warm, pour together, mix thoroughly, allow the mix to cool (mix occasionally as it cools) and store in an air tight container to prevent water from being absorbed by the isopropyl. For a spray bottle you can use an old commercial spray lube bottle or an old pump hair spray bottle that has been thoroughly cleaned. To apply the lube, spread the cases in a single layer on a clean surface like an oven tray (those disposable aluminum oven liner trays are great and lightly and evenly spray the cases. Allow the cases to sit for a couple of minutes, roll the cases around and lightly spray again. Wait until the alcohol has evaporated (about 5 minutes) and start sizing. Properly lubed cases will have a slightly greasy feel to them without feeling slimy. Another neat idea for spraying the cases is to put them in a plastic bag, spray, and then mix the cases, dump out on some newspaper, and let dry. Less messy than putting the cases on an oven tray. If you have a hard time finding liquid lanolin you can mix a small tub of Hornady Unique case lube and 16 ounces of 91% or 99% isopropyl. If you use the 91% isopropyl you'll need to shake the mix to keep it suspended. Thanks to Steve Dzupin for this tip (Fr Frog's).
- Switching compensators
-
New York Times Article on Assault Rifles
Who the hell was asleep at the switch at the NYT when this article came up for publication? Is the NYT publishing staff on crack? Curious minds want to know!
-
Any experience with "Quality Made Cartridges"?
The reason for 200 LSWC is for bullseye shooting. Round is usually loaded light, just enough to get accurately to the target. The bullet will "cut" a perfectly round hold in the paper target. Important for scoring, because all you have to do is nick the circle outline to get credit for that ring's point value. The 200 grain weight is the sweet spot between speed and accuracy
-
Pod 308
The market is flooded with 'evil black' rifles. Nobody is buying, inventory is high. Look for big sales coming down the pipe. I feel if things remain calm you'll see deals like you never have this holiday season. Look for ammo, except 22, to crash in price soon. Lots of rumbling in the marketplace.
-
. 224 pills
Find new sources. Reloads can be done for .21/ea. Reusing brass. Savings is in the pill cost and reusing brass. Primer and powder savings is small potatoes.
-
Your First Shot
About 9 or 10 with a J C Higgins pump action 22. Still have it.
-
Pod 308
OK, so if I bought it thinking it would have some collector value on down the pike, I guess I just got screwed. (No I didn't, nor will I buy one). Just making an observation. Buy guns to shoot them, not for investment.
-
Pod 308
Thought these were a special run of only 500? Tanner's 320 available? Or something else?
-
First Ar-308 Build And Problems Already
Yesterday I was lucky and got my hands on a 8 pound tub of Lil' Gun. Back to loading for the 300BLK and the 458 SOCOM. Heads are back in stock so a shooting we will go!
-
Looking for a lever gun
Levers and SA wheelies go together like pb and jelly. What's not to like?
-
Mosin Nagant Ammo Concerns
For some ranges if the magnet sticks, it's a no go. Their range, their rules.