Everything posted by T Bill
-
10 mm suggestions
Skip the G17/G19 craze. Pic a glock in 40 S&W is the answer. Then get a Lone Wolf 40-9mm conversion barrel. This is the way to go. The G20 can take a 10/40 barrel as well as a 357Sig or a 9X25 barrel. Plan on reloading. This way you can create custom rounds for your needs. Yeah, you don't save money, but you shoot a lot more.
-
Minimum NRA member age?
No. Congratulations and may God bless you, your family, and especially your new family addition.
-
Light Primer Strikes - Please help
Hammer Spring in upside down, reverse so spring legs come off pin from bottom not top See diagram I posted previously from Arfcom, you'll see difference.
- +1 MidwestPX
-
Uncle Ted body slams Piers Morgan
Piers Morgan is a hack journalist from Britain. Look at his backround. He has hacked his way from one journalism job to another. He had to come to the US, Britain had no use for him anymore. The new head of CNN, Zucker I believe, is no friend to the 2A either. Beware, be very aware
-
Light Primer Strikes - Please help
TRIGGER ASSEMBLY PARTS: Trigger, Trigger Pin, Trigger Spring, Disconnector, Disconnector Spring TOOLS: 5/32" drive pin punch Shoulder trigger spring onto trigger with ends of spring forward and under. Install disconnector spring with the wider portion of spring down towards trigger and push until it locks in there. Position disconnector on top of trigger, where trigger pin will hold both in place. Insert trigger assembly into receiver. Insert trigger retaining pin through receiver, trigger, and disconnector. The trigger pin has 2 grooves in it; one in the middle of the pin and one off to one side. It does not matter which way it is inserted, though common practice is to insert from left to right, with the groove to the left. Insert hammer pin from opposite side to help align things as you push the trigger pin in and the hammer pin out. You will have to push down on trigger assembly to align the holes and get the pin in all the way. FUNCTION CHECK Make sure that the trigger pivots smoothly when depressed. Verify that the disconnector pivots when pushed. HAMMER ASSEMBLY PARTS: hammer (with J-pin installed), hammer spring, hammer retaining pin TOOLS: 5/32" drive pin punch Install spring onto hammer, ends of spring to rear and shoulder on back of hammer. Install hammer in receiver with feet pointing rearward away from hammer Use 5/32" punch to retain hammer in place as you insert hammer retaining pin. Like the trigger pin, you may have to push down and align the holes perfectly in order to push the pin in all the way. Ends of the hammer spring will rest on top of the trigger pin, with one end in the groove on the trigger pin. Inserting the hammer pin may require some effort, as the J-pin in the hammer will catch the grooves in the pin. FUNCTION CHECK Verify that hammer locks to the rear when pushed back. Verify that hammer pivots forward when trigger is pressed. Without releasing the trigger, push the hammer back again and verify that it locks (caught by disconnector). Releasing the trigger should not cause the hammer to pivot fully forward (caught by trigger). Hammer will fall when trigger is pressed. <a name="selector">
-
Shotgun Shootout! February 3rd at Clinton WMA
There are no assault rifles. Just really cool sporting arms (wink, wink.)
-
Light Primer Strikes - Please help
Three Springs in FCG. Hammer, Trigger, Disconnector. I don't know what DD is using for spring strength, would assume MIL-Spec. Try cleaning bolt carrier first. Get some auto parts brake cleaner and spray down the firing pin hole in the bolt carrier and use a small caliber cleaning brush to clean out. Maybe some left over crud in there. Spray firing pin also. Make sure all parts are installled properly in BCG. Try again. If no better, I would look to make sure hammer spring and trigger spring are installed properly in lower. Are they in correctly? Reference pictures on AR15.com in the manual section. It is possible for them to be installed improperly causing light hammer strikes. Good Luck.
-
Reloading components - where to buy in central jersey?
NJ Sigfan, Make a wish list, hookup with DamjanBlues on Wednesday and take the trip. It will be worth it. Include dies and shellplates on that list. With Tony at TNT you never know. It might just be there! Once fired brass is hard to come by right now. That will take some digging to find it.
-
Light Primer Strikes - Please help
Ammo with a plus sign in side of circle on case head is NATO Spec with hard Mil Primers. Hammer spring or firing pin in the problem here. Also, russian ammo has very hard primers. Would your hammer spring happen to be painted yellow? If so, JP reduced power springs may be installed in FCG. Then this is the problem. Change to full power springs if you plan on shooting Mil-Spec Ammo. New Springs can be ordered from Wolff Springs.
-
Long gun/Rifle sale/transfer form
www.njsp.org/info/pdf/firearms/sp-634.pdf
-
Facebook discussion: "one pin turns it into full auto"
Glad to lend an ear. Sorry, did not mean to belittle you. My bad. Glad to have you as a true American.
-
Facebook discussion: "one pin turns it into full auto"
For your own information so you know the facts ar-15 comes from the Armalite Corp. designer of the AR-15 rifle. Why AR-15? Well, Armelite had multiple rifles/shotguns for sale from the AR-1 thru the AR-15. Some were even bolt action. When they were in financial problems they sold the rights to Colt. Colt sold the civilian version of the AR15 in 1963. It has been in civilian hands for 50 years. As far as SA to FA, it is a completely different FCG and BCG. They must be replaced en mass not upgraded with a pin. This LEO has his rights to his opinion, but jeez make it an informed opinion, I find it amazing how many LEO's have little or no backround in firearms. It is a tool of the job.
-
Dammit! Why Didn't I Think of That???
Liberals tend to move so fast and are so tunnel visioned that they forget to check the steps that make a country strong along the way. Obama and this, Cuomo and the SAFE Act, and even our assembly women Jimenez and the new proposed gun laws. It really shows how there kind are not qualified to serve in public office. If this were a corporation it would be bankrupt and out of business. Oh wait we're bankrupt and about to be out of business.
-
School me on crossbows
In the 300-500 dollar range barnett and horton are GTG
-
Question about the 1994 ban, for those who remember it
I am sorry. Us oldtimers only remember the NJ Ban as it was enacted before the Federal Ban. From there the Federal Ban did not effect us if I remember correctly. We had already been screwed by Florio. And grandfathering / registering had long expired in NJ by then.
-
Question about the 1994 ban, for those who remember it
Very Similar. They did what they pleased without input from the public. You had one year to comply. Register it (a joke), surrender it (NFW), or move it out of state (as the majority did). We will see what this round brings.
-
Lonewolf .40 cal to 9mm conversion question
The base of a 9MM case is .394. For the 40S&W is .424. The difference is .030. Half that distance is .015. So your primer strike is off by .015 inch (on paper). You can hardly see this let alone worry about off-center primer strikes. This is not a factor at all. Primer strikes vary more than this from pistol to pistol.
-
NYT Op-Ed / Is This For Real???
He's only in Texas because of the teaching job at Rice University. He is trolling OpEd pieces to keep his name in the limelight and make some spare cash on the side. He is a mole of the worst kind. Will not read his books, or see the movie when his Hollywood chronies make it. Just like to know why he left LaSalle University in Philadephia for the job at Rice. I guess the sponsorship for the Author in Residence job expired or was withdrawn. If the job was a BU i bet this piece would not have even been written or published.
-
Lonewolf .40 cal to 9mm conversion question
None
-
Working on an FFL for a New Location in Sussex County
Transfers for $42.80($25 fee, 15 NICS and Tax) would be very competitive for the area you are in. A vendor in the Warren county area charges the same and is doing very well.
-
Glock 17 vs Glock 19 - which should I get?
Sorry but over the years speaking to gun store clerks has left a bad taste in my mouth. I rarely get an informed answer that makes me better. These types of forums have real user opinions. In the past it would take me months of going to matches and shows speaking with the people who use the products for me to see if it was worth it. Over time you will get to know the people whose opinion you trust. With that said, (sorry for the rant): The AA conversion includs a complete upper to go on the frame. It is a very stable platform and works very well. You will like it when you get it. I enjoy it on the G21G4. Second, conversion barrels work. Lone Wolf's conversion barrel has two features on it that make it reliable. The case wall of the barrel is thicker to make up for the different in bullet diameter. If you were to look at the top of the frames for the g19 and the g23 the primary difference you would see is the ejector is crooked on the 9mm, straight on the 40. Looking at the chamber of the Lone Wolf barrel you will see it is slightly off center to the left to better align the ejector with the case ensuring reliable case ejection. I know several people that have them and no one is complaining. They love the ability to shoot cheaper 9mm on the same platform. Most have tricked out the frame with a different trigger, sights, etc. and the conversion barrel allows them to practice or plink with cheaper ammo. I have been at the range with them, switching between 22, 9, and 40 without any problems. Good Luck on whatever you choose.
-
Rifle reloading question
If you are interested in Bench Rest Shooting then every step in reloading is trying to achieve consistency and accuracy in every shot. Same everything. Working the brass to exact tolerances. Old School is correct, case length and OAL is primary. You want each round to camber on the shoulder the same way, at the same length. Some long range hunters will do this to ensure accuracy for extreme long range hunts. It takes a lot of patience and time working up loads and getting the most out of them. BR shooters will go to extremes you would not believe. Searching for componets from vendors by lot number, DOM, etc. L E Wilson makes a fine set of case gauges that you can use. It will check OAL, Neck length.
-
Glock 17 vs Glock 19 - which should I get?
Glock 23 with Lone Wolf Aftermarket 9MM conversion barrel ($110) (storm lake is another vendor) and mags ($25) are the way to go. Add AA 22LR (+/- $300) when you can. You could also get a 357Sig Conversion barrel and mags and go in any one of four calibers. A Glock 22 with the same options is just a viable. The aftermarket barrel will let you shoot 9mm lead. Something to think about as prices keep climbing. Reloading as the next step? Next Glock for me will be Glock 35 Gen 4. Have a G21G4 with AA conversion that I love. Almost makes me pass on using the MKII and the 1911 45.
-
Thoughts and Prayers for HenryM's father
My familys condolences to yours. May you find peace.