From the Father Frog’s Website…………………..
Homemade Cleaners Firearm & Lubricants
Gun Oil Substitutes
Keep in mind that no matter what lubricant you use, you should use the minimum amount of lube possible. You want it lubricated and not an oil field.
Synthetic Automotive Oils
Synthetic automotive oils (such as Quaker State High Performance Synthetic, Castrol, and Mobil 1) work well as general lubricants and because of their detergent capabilities they will help to remove "crud." (Synthetic oils handle low temperatures better than regular oils.) Just remember, as with any lubricant, not to over lube things. Valvoline Semi-Synthetic Power Steering Fluid has also been used with great success by many folks as their normal lubricant.
Slick Stuff
This very "oily", (i.e. slick, greasy) lubricant appears to adhere very well to metal, with little or no creep. Thus it does not appear to drain from slides and parts during extended storage. From the formula it appears that it might not be suitable at very low temperatures.
2 parts Dexron II or III automatic transmission fluid 1 Part Mobil-1 Synthetic Oil, 30 weight, or 10W-30 1 Part STP Oil Treatment (the stuff for "old" cars w/ over 30,000 mi.)
Thanks to John Nichols for this tip
Amsoil
Another excellent home brew lube is Amsoil Synthetic ATF with some lanolin added to make it even slicker. A synthetic grease from TS Moly (www.tsmoly.com) called Arctic Grade TS-67 also makes a great lube especially for cold weather. It is a totally synthetic moly grease with the consistency of chocolate mousse. It does not run, weep or smell (very important for the SAF (spousal acceptance factor)). It is reported to work fine at -30 degrees.
Thanks to Roger Rothschild and Mike Gieger for this tip.
Slippery Stuff
Try 80 percent Marvel Mystery Oil mixed with 20 percent Slick 50 .
Thanks to Jim Conway for this tip.
Ed's Red Oil
As a general bore cleaner, plastic wad remover, and carbon solvent the following formula, a creation of C.E Harris, and dubbed "Ed's Red" works quite well. In fact many folks claim it is better than anything they've tried. The original formula is:
1 part Dexron II, IIe or III Automatic Transmission Fluid - GM Spec D20265 or later 1 part K1 Kerosene 1 part Aliphatic Mineral Spirits federal spec TT-T-2981F (CAS# 64741-49-9) or Stodard Solvent/Varsol (CAS#8052-41-1) 1 part Acetone (CAS#67-64-1)
Formula Addendum
It has been reported that methyethylketone/MEK (CAS#78-93-3) can be satisfactorily substituted for the acetone if desired.
It has been reported that Turpentine can be satisfactorily substituted for the Mineral Spirits if desired. The original Frankfort Arsenal formula upon which Ed's Red is based used turpentine rather than mineral spirits which were substituted for lower cost. Turpentine also tends to leave a gummy residue.
It has been reported that Kroil penetrating oil can be satisfactorily substituted for the kerosene if desired.
It has been reported that the lower numbered "JP" jet fuels can be used in place of kerosene.
It has been reported that Goo-Gone (a commercial citrus based solvent) can be satisfactorily substituted for the mineral spirits if desired.
It has been reported that commercial automotive "engine flush" can be substituted for the ATF (but you lose the red color).
For each gallon of Ed's Red produced you can also add 1 pound of anhydrous lanolin (CAS#8006-54-0), which helps to neutralize fingerprints but it's really not necessary and current formulations generally omit it. You can also leave out the acetone but then it doesn't remove plastic wad fouling or penetrate as well. Store in airtight chemical-proof containers as the acetone, if used, will evaporate. Two sources for bulk anhydrous lanolin are http://www.selectoils.com/item--Lanolin--SO-Lanolin.html and http://www.thesage.com/ .
According to Ed, "Ed's Red" will flow at -65
oF and won't carbonize at 600oF. It has seen use by both the FBI and the Army Marksmanship Training Units.
MIXING INSTRUCTIONS Mix outdoors, in good ventilation. Use a clean 1 gallon metal, or chemical-resistant, heavy gage NFPA approved plastic gasoline storage containers. Do
NOT use light weight, thin, high density polyethelyne (HDPE), which is breathable, because the acetone will gradually evaporate. Don't use PVC containers as they will dissolve. A possible online source for metal 1 pint and 1 quart screw top metal containers suitable for storing Ed's Red is http://www.taxidermy.com . This site appears to be some sort of frames based design that does not allow you to link directly to containers, but you can find them via the following site links Products | Molding and Casting | Containers, Cups and Tools. The Blitz USA line of approved gasoline containers can be obtained at Auto Zone, Home Depot, Walmart, Target, and other retailers and are what I use. (www.blitzusa.com).
Add the ATF first. Use the empty container to measure the other components, so that it is thoroughly rinsed.
You can divert a small quantity, up to 4 ounces per quart of the 50-50 ATF/kerosene mix for use as an "Ed's Red-compatible" gun oil. This can be done without impairing the effectiveness of the mix.
INSTRUCTIONS FOR USING a) Insure that the firearm is unloaded and that all magazines are removed. Cleaning is most effective when done while the barrel is still warm to the touch from firing. Saturate a cotton patch with Ed's Red, wrap or impale on a jag and push it through the bore from breech to muzzle. The patch should be a snug fit. Let the first patch fall off and do not pull it back into the bore.
b) Wet a second patch, and similarly start it into the bore from the breech, this time scrubbing from the throat area forward in 4-5" strokes and gradually advancing until the patch emerges out the muzzle. Waiting approximately 1 minute to let the bore cleaner soak will improve its action.
c. For pitted, heavily carbon-fouled "rattle battle" guns, leaded revolvers or neglected bores a bronze brush wet with bore cleaner may be used to remove stubborn deposits. This is unnecessary for smooth, target-grade barrels in routine use.
d) Use a final wet patch pushed straight through the bore to flush out loosened residue dissolved by Ed's Red. Let the patch fall off the jag without pulling it back into the bore. If you are finished firing, leaving the bore wet will protect it from rust for up to 30 days. If the lanolin is incorporated into the mixture, it will protect the firearm from rust for up to two years.
e)
Wipe spilled Ed's Red from exterior surfaces before storing the gun. While Ed's Red is harmless to blue and nickel finishes, the acetone it contains is harmful to most wood finishes and it could damage some plastics if left in prolonged contact.
f) Before firing again, push two dry patches through the bore and dry the chamber, using a patch wrapped around a suitably sized brush or jag. First shot point of impact usually will not be disturbed by Ed's Red if the bore is cleaned as described.
It has been reported that when Ed's Red is used exclusively and thoroughly, that hot water cleaning is unnecessary after use of Pyrodex or military chlorate primers. However, if bores are not wiped between shots and are heavily caked from black powder fouling, hot water cleaning is recommended first to break up heavy fouling deposits. Water cleaning should be followed by a thorough flush with Ed's Red to prevent after-rusting which could result from residual moisture. It is ALWAYS good practice to clean
twice, two days apart, whenever using chlorate primed ammunition, just to make sure you get all the residue out.
Thanks to Jim Dodd for the above instructions
An unusual use for Ed's Red. Several correspondents report that an application of ER to an ant hill, especially fire ants, kills 'em dead.
Also, Ed's Red is very penetrative and makes a superior penetrating oil for loosening rusted parts. In fact in some testing by a machinist's magazine a couple of years ago it beat
all the
commercial products by a wide margin. A dedicated ER penetrating solution can be made by just using a 50-50 mix of ATF and acetone.
A historical note about Ed's Red. When Ed Harris first cooked it up, it exceeded the then current Mil Specs for bore cleaner and CLP. Ed and a cohort were able to test it at a defense contractor's quality lab after hours with chrome-moly and stainless samples provided by Kreiger Barrels.
Eds Red Plus
This variation on the Ed's Red formula gives it a copper removing ability similar to the commercial bore cleaner Marksman's Choice MC-7. You will need:
11 ounces of basic Ed's Red 2 ounces of 10%-20% industrial strength ammonia 2 ounces of Rustlick WS-11 cutting oil or suitable alternative 1 ounce of Murphy's Oil Soap
Mix the oil soap and ammonia in a separate container. In a suitable 1 pint container containing 11 ounces of Ed's Red, add the cutting oil and mix together. Then add the oil soap/ammonia mixture to Ed's Red/ cutting oil and shake the container to mix the ingredients. You will end up with a pink opaque liquid that for the most part remains in solution, but some components may settle out over an extended period. It is always best to shake well before using. The resulting solution will remove mild copper deposits in bores if allowed to work about 15-20 minutes.
Water soluble cutting oils and rust inhibitors can be obtained online from http://www1.mscdirect.com/cgi/nnsrhm or locally from your industrial supplier. NAPA auto stores carry a soluble oil listed as NAPA Soluble Cutting and Grinding Oil," part number SL SL2512. Metal screw top containers can be obtained from http://www.taxidermy.com under | Products | Molding and Casting | Containers, Cups and Tools.
Thanks to Bill Mecca for this information.
You can link directly to that frame by using this URL http://www.taxidermy.com/cat/18/tool.html, but there's no link back to their home page from there.
Thanks to Patrick Larkin Jr. for this tip.
In a pinch you can use straight mineral spirits as a rather good bore cleaner.
See the ER recipe for an ER compatible oil. Just a 50/50 mix of ATF and K1 kerosene. Straight ATF works very well too.
Lanolin
We've mentioned lanolin in several places as an ingredient, but liquid lanolin also makes a very good warm weather, lubricant for high pressure wear spots like sears and other wear point all by itself. It also is an excellent preservative/rust proofer (well known to marine users in that role). It has also been used as a bore conditioner for .22RF barrels by running a lanolin soaked patch
through a clean bore, followed by dry patches until nothing remains on the patches.. An Australian company called Lanotec (www.lanotec.com.au) sells liquid lanolin in an aerosol can but I'm not sure if it's available in the US.
Thanks to Dave York for reminding me of lanolin as a lube.
Automotive "moly" Grease
Excellent for sears and hammer notches - just use a little.
NOTE: WD40 is NOT a satisfactory lubricant for firearms as it tends to become gummy as it dries.