Everything posted by Vlad G
-
870 Bullpup stock
I'm looking at that thing and all I can think of is "Yes, because reloading shotgun quickly wasn't complicated enough, this clearly is the answer"
-
recommend a bolt cleaning tool
Gunsmiths love it when people use dremels.
-
2 piece free float drop in rails
Yeah I don't see why that would be an issue. There are basically 3 things that fit over the barrel: 1) Barrel nut. This is pretty sizable, it will fit over anything but the "tank break" type comps 2) hand guard itself, this is even bigger 3) Gas block and that is your tricky one because it won't (unless you have a .750 diameter comp like Nordic Tactical). If you go to a two piece gas block this all goes away. There might be some bits like the front hand guard retaining parts but you can cut those off as you won't need them once you go free float. I'd say pick a slim low profile gas block and run an extended hand guard over it. The YHM-9378 has block would work.
-
2 piece free float drop in rails
If you are going to take out cutting tools, cut off the front sight/gas block and get a new two piece one to replace it. Then you can remove everything over the muzzle and you have all the options you want when it comes to handguards, because barrel nut should fit over the any non-absurd muzzle device.
-
2 piece free float drop in rails
Basically drop it flee float over a delta ring is hard and messy. You are better off doing it right and stripping everything off the barrel first. This could be messy because of permanently attached comps which is why clamp on gas blocks are important, everything else should fit over the comp.
-
Looking for private land to shoot on
Quick reminder, most shooting clubs are private land you can shoot on. Join one.
-
World War Z (the movie)
anyone notice that there were no fat zombies? Whats up with that?
-
"Cz 75B's are hard to find"
Find a decent local dealer, form a relationship, have him find it for you and order it.
-
recommend a bolt cleaning tool
An empty .308 case makes a fine scraper and being brass you won't damage much. Also, not that important to keep clean as people make it out to be.
-
traditional scope vs eotech with magnifier
The holy grail is a 1-6x or 1-8x scope which acts as a red dot at 1x with daylight visible illumination. This grail is actually getting there in so far as they exist, but the entry point is $1400 and they get to be as much as $4000+
-
.50 muzzel loader bullets banned?
I find that very surprising, seeing how they've shipped me stuff just fine.
-
.50 muzzel loader bullets banned?
Call Cabelas back and ask for a supervisor. Sometimes they get broken ideas in their system and you can get them cleared out, they are actually pretty decent about this.
-
Herters 223 oopsie
I've seen no flash holes on a different types of russian ammo. I've even seen it on PMC once. When ammo is on cheap side and there are shortages and factories crank out all they can, shortcuts are taken.
-
Machine gun-like rapid fire rifle - that's legal.
Spend your money on ammo and practice.
-
Where is the CJR&P USPSA Match thread for 9/8?
Scores are up. Send me any corrections you might have, but I won't get to them until after next week.
-
Where is the CJR&P USPSA Match thread for 9/8?
Almost there, I hope to have them up today or this tomorrow. .
-
Extended quad rail help anyone make a
Yeah it is beyond theory though, it happens and it is pretty easy to test out by applying some pressure the hand guard like propping against a vertical post or something. The other option is to mount a flip front sight in front of an extended handguard if your barrel profile and length allows it. Basically take your favorite flip-up that comes with a gas block, and just mount in in front of the handguard, without being an actual gas block. If your barrel profile is right, this works, specially if you use the kind that has screws at the bottom, dimple the barrel and locktite the screws in place.
-
IDPA / USPSA - how do I get better ???
So I can give one piece of advice I'll give to anyone who is serious about learning to shoot faster and learning how to decide when to go for speed and when to go for precision and states in between: Buy a book named Practical Shooting: Beyond the Fundamentals by Brian Enos. His book at be at times a bit zen and a bit dense because he isn't really a writer, but his chapters on the types of sight pictures and focus are very very good. Also if you are seriously interested in practical shooting the forums at brianenos.com are probably the ultimate place to learn about the games we shoot.
-
Primer Brands
The only primer I can recommend against are Vihtavuori, they are exceedingly odd. On the bright side, they are almost never available, anywhere. The ones I tried I bought off the shelf in a gun shop simply for the WTF'ness of it, as I didn't even know VV made such a thing.
-
Argh....Stove Pipe!
1) one stove pipe is not worth your worry, ask again later if it keeps happening. 2) the cz thing could be the profile of the ejector. There is a possible error condition on the cz platform depending on fit. Mine picked up this issue after about 20k rounds. I had replaced barrel, extractor, etc and problem remained until I reprofiled the ejector
-
NASA Launching unmanned mission to the Moon tonight from VA.
I think you can buy telescopes big enough to see the landers if you spend some coin. Or you can shoot a laser at the mirrors they installed.
-
What is the proper way to install a castle nut
If it gets loose is not that the recoils system falls out, the first thing that falls out is the spring for the take down pin retaining pin.
-
What is the proper way to install a castle nut
http://www.ar15.com/forums/t_3_4/315921_Headspace__Torque_values__and_Barrel_Break_in.html
-
Where is the CJR&P USPSA Match thread for 9/8?
Yes, we have a webpage where we announce these things, the thread here is started if members care to start it. Remember that we have lots of people shooting USPSA who never visit this forum
-
S&W mp9c take Down procedure is a PIA!
Really? What is the issue with the 75? Align notches, push out slide pin.