M1152

Mosin–Nagant (or as the magazine is naming it Russian Repeating rifle) for $9.95 LOL, How times have changed.

A guy walked into a crowded bar, waving his unholstered pistol and yelled, "I have a 45 caliber Colt 1911 with a seven round mag plus one in the chamber and I want to know who's been sleeping with my wife". A voice from the back of the room called out, You need more ammo!

According to Clinton News Network "The names and addresses of the two counties' permit-holding residents were obtained through the Freedom of Information Act", see link here

I received the Gusciora one today as well, at least he responded and I wouldn’t have expected anything less from him. He’s your typical NJ Democrat politician with the Nanny state logic. Gusciora and Bonnie Watson Coleman have been A-hole buddies for years and you see the results (or aftermath) they have provided for Trenton. Bonnie as you may remember moved on in 2015 to become a US Representative and was the centerpiece of a recent NJ2AS undercover video. For those keeping count I’m at 4 Yea and 1 Nay and that and a $1.20 might still get you a cup of coffee at the Wawa.

bump / signed

email sent...

I put two of them in. The challenge (if any) is trimming the roll pin for the safety. I put the first ALG in when they first came out and I recently purchased a second one a few weeks ago. The recent one was shipped with an optional spring to add a little more tension. I wanted try the optional spring but it wasn’t going to fit because of the Saiga BHO. If you put one in you’re going to end up with about a 3.5lb pull and shorter pre & post travel if you're OK with that. Other than that I like it, I never used the red star but its a step-up from the Tapco IMO

Actually that’s a very good idea if we could get it to fly. I'm sure you remember but for those that don't a few years ago the libtard lawmakers in CA opted to pull out ALL their state investments in ALL Firearm related companies. IIRC I’m pretty sure they accomplished that there. Off topic but the Trenton politicians seen that and tried to do pass that here but CC vetoed it. So back on topic, if the CA lawmakers hate firearms that much, then hell yea pull the plug on their PD’s too.

I was listening to the newly posted GFH Radio program and Mr. C states that the State of California representatives exempted themselves from the legislation. If you only have a few minutes and can't listen to the full broadcast fire up your media player and fast forward to the 34 minute mark EDIT: added video

If you don’t know what to do with it reach out to the Naval Air Station Wildwood (NASW) Aviation Museum. There’s a good chance they would take it off your hands and they are good people, plus you would be doing something good. I donated non-Aviation items to the NASW, they are NOT a STATE Museum.

It won’t load in Firefox with privacy add-ons, that was my experience. I launched Internet Explorer and it came right up. Just another reason not to like Microsoft

after 3000 post and you're asking now? Simply answer

voted..

you might want to google NY SAFE Act and/or take a look here

just to follow up I received and email back and was advised I was not affected. FWIW my last order was in December

thanks for the heads up, I haven't received any notice from AIM yet so I emailed them... so we will see... ^ ^ this

I’m no expert, just a DIY guy. It really depends on how many other NG appliances you currently have in service and the length of the run you would need to add to provide NG for your gen to calculate BTU usage. US Carb previously had some formulas on their website but it looks that link is down, perhaps give them a call for pipe sizing. Also keep in mind that If you’re on the fringe or come up short you would also need to have your NG meter upgraded as well for more volume. Chances are you don't need to do that if you could tap off and existing line and only need to run a few feet w/o a lot of fittings and turns (90 degree bends) but something else to look into. If you are exploring the US Carb kits the engine horsepower determines the kit you purchase and not so much the Gen wattage. Take a look at their website for kit requirements.

Good question, I’m on NG so I can’t say for sure. Below are two youtube vids for single tank propane setup, one with reg and one without. without Reg With Reg I would call or shoot US Carb and email during their normal business hours and I'm sure they will provide a detailed answer for your configuration

I have a 5500 running watts 12hp B&S connected to a 1/2inch NG line with 3/8inich Quick Disconnect for our grill. I think most folks will tell you go with 3/4inch but my setup works nicely on the 1/2inch black iron reduced to 3/8 at the quick disconnect with a 12’ hose going into the NG regulator. The regulator will only allow so much gas in at time anyway. You just need to make sure you have the volume and your other appliances like your stove, hot water heater and furnace aren’t sucking off too much NG so its YMMV. I ran ours during Sandy as well and no issues. I have the original kit, not the promo above but the SNORKEL adapter in the new kit is better IMO because of the smaller profile. The original adapter was huge and some folks had to do some serious mods like cutting the frame to adapt it. I didn’t have to do that, my conversion was easy.

Couldn’t agree more with you but anything else would require them to actually do something. Instead the NJ legislator’s method of operation is to dick around with pointless shit like this and create more infringement on the 2A which in their minds gives the perception that they are doing something. It’s all self-serving.

Forgetaboutit, let them pass it…. it will be will be about as enforceable as the cell phone laws when driving. This is only more proof what our idiot lawmakers are capable of doing edit: typo

Thanks for posting, glad to see Charlie is on-board. I’ve been a CDB fan for a couple of winters now, I seen them in concert at the original NJ State Fairgrounds (AKA the Old Trenton Speedway) back in the 70’s and they were great. Charlie don’t pull any punches, he tells it like it is…

thanks, I’ll have to explore it further...

Quick question if you don't mind, So If you had to you can remove and slide the tube off/over the brake? I realize the gas block isn’t going anywhere but I always thought the pinned brake locked-in the free float rail as well. I’d been entertaining the thought of doing a build with a free floated rail but the pinned brake was always deal breaker since I thought the tube was not removable for repair/replacement do to the pinned brake. Thanks in advance

IMHO I think that one is pretty straight forward, if your friend is stable its simply NO and move on… unless you’re Evan Nappen this is how we are all conditioned to think about firearm laws in NJ. so NO I don’t think you are over thinking it.