Everything posted by mikeyjones
-
Which primers with the Lee Loadmaster?
Lee recommends cci because they're a little harder cupped and seem to slide a little smoother in their chute but I wouldn't worry about it too much. When I was using a lee press exclusively, I used all different brands with no real issues.
-
loading up .45ACP'S
Same. .470-.471 as measured by my calipers.
-
Brass question for the reloaders
So general consensus is to sell it dirty. Maybe offer processing as "upgrades". I'll have to see what kind of shape the brass is in when I get it.
-
Powder Valley has 12million Tula Small Pistol Primers in stock
PV just got a shipment of Tula SP primers in stock. 20k limit per item per order. http://www.powdervalleyinc.com/
-
Brass question for the reloaders
I use SS media to clean all of my brass. So it would be cleaned using that method.
-
Brass question for the reloaders
I might be getting a large shipment of 5.56 brass in a month or so from a military range. Now here's the question, when you buy your brass, do you prefer it dirty, cleaned, decapped, swaged, trimmed, etc? If I'm going to sell it, I'd like to batch process it to a standard most people would want. Thanks
-
Cell providers other than Verizon - Hunterdon county
H2o is att, simple is tmobile. Net 10 depends on where you are and luck of the draw.
-
Remington 5 1/2 small pistols primers magnum
#6 is seated upside down. I wouldn't be surprised at all if some of them were crushed during seating.
-
$25 NFA Lower
Here is their FB page that mentions the deal: https://www.facebook.com/SecondAmendmentShooting Here is their # 850 615 4867 I'm torn as to whether I should order or not.
-
$25 NFA Lower
If I didn't already have 2 builds going on, I would order another.. Did anyone try it yet?
-
$25 NFA Lower
http://www.slickguns.com/product/new-frontier-armory-poly-lower-25 Get them while you can. Just follow the link on slickguns and call the gun store.
-
30 round magazine question but not what you think
Lever action != semi auto
-
Cell providers other than Verizon - Hunterdon county
It's a good route. Just be aware that for a smart phone, you'll have to either buy one from them or pay to have yours flashed over. What phone do you currently have?
-
First gun for short fingers, 9mm, low muzzle flip
I don't think anyone has mentioned it yet so I'll put in my 2 c. I would consider the glock 17c for lower muzzle rise. It's ported out of the top so gasses keep the muzzle from rising too much. I like mine although I'm really not sure how much the porting really helps. I have both a stock and ported barrel and I shoot slightly better with the ported.
-
Remington 5 1/2 small pistols primers magnum
It's the same brass you've used before? Brass varies by headstamp and even by lot. You as a reloader cannot put a crimp in the primer, but some ammo for military/le has the primers crimped in place. It makes the primer pocket really tight and needs to be swaged or cut before reloading. We really need more measurements before trying to guess. There's two different issues going on. Right now, I would take a few cases and resize them and see if they drop into your chamber. If they do, they're being resized correctly. Then the issue is likely oal or crimp(of bullet). The primer issue might be crushed or mutilated primers caused by crimped primer pockets or just brass with really tight pockets. Could also be seating depth. Could you post a few pictures of headstamp area of the rounds that didnt go off?
-
Remington 5 1/2 small pistols primers magnum
Edit to above post since Tapatalk wont let me edit it. I see that you're saying chamber check so I assume that's your barrel. Are these cast bullets, plated, jacketed? Could be a crimp issue, could be oal. Have you tried just seeing if the resized brass will fit before it's loaded? To accurately check the depth you'd need a depth gauge. The fact that 1 went off the 2nd time around gives me some idea that they might not be seated deep enough. Either that or the primers are getting crushed during seating. That's why I asked about primer crimps above.
-
Remington 5 1/2 small pistols primers magnum
What caliber is this? Was the brass crimped? Did you swage the primer pockets? As far as passing the gauge, just take your barrel out of the gun and use that as the gauge instead. My 45 cast loads dont pass my Lyman gauge but function flawlessy in my 1911s.
-
Pantano vs NJ or CCW is coming... sorta maybe not quite
Nj2as was talking of doing this. They're waiting to hear if a rejection will have any lasting effects on people's records. Ie will job prospects, p2p, nics be able to see that you were rejected.
-
Remington 5 1/2 small pistols primers magnum
Have you checked the primer seating depth? Do these primers go off if you strike them again?
-
Primary HD "Weapons"
Just got these pictures from our breeder the other day. picking him up sept 6
-
Good .357 Load In A Carbine?
Lots of unburnt powder in the barrel is a sign that pressure isn't getting high enough. Add more powder!! I'd also possibly try a magnum primer if you have any, although that's not going to make a lot of difference. Right now you're getting an inconsistent burn and therefore your pressure is going to be all over the place. I bet if you chronoed the bullets, you'd see a very wide spread and well under what that bullet needs to properly stabilize. Work up your load slowly and I'm willing to bet you'll see better results with higher charges.
-
Been waiting for my FPID and P2P since Jan.
Who do you guys call in trenton? My pd has usually been 3-4 weeks but this time they're telling me 3 months. I called today (after 30 days of waiting) and was told that the state police was holding it up. Just wanted to give them a call and see.
-
Hi from Mt. Olive
How long did it take in mt olive? Sent from my TF300T using Tapatalk HD
-
Stupid NFA question.
Actually if you form a revocable trust, no CLEO signature is needed. Still wonder how this would work in nj.
-
The build begins!
I got a blem from psa as well and about the only thing I found wrong was a scratch inside the magwell. I'll take that all day.