MauserCollector

I see the Keltec for sale at least once a day. Usually it is the Glock version. The Beretta version not so often. I personally don't mind the Beretta CX4 Storm, but it is at least 50% more expensive than the Keltec. I picked up a .45 CX4 Storm with accessories cheap. However magazines only hold 8 rounds. If you want more than 8 they are very expensive. I wouldn't buy high point anything. Personally I would get a Keltec it can be more compact and less expensive. Sent from my XT1585 using Tapatalk

Perfectly legal and useless as far as I can see. As a previous poster said buy a Keltec Sent from my iPad using Tapatalk

Good for you. Hopefully you moved to Free America Sent from my XT1585 using Tapatalk

Russian and Romanian are the best. Albanian too but more rare. Chinese not far behind. Yugo are least respected but also least expensive. Expect to pay $750+ for Albanian. $500-$650 for Russian. $450-500 for Romanian and Chinese. Yugo $350-450 depending on condition. Matching numbers adds value. Personally I like the Romanian. Sent from my iPad using Tapatalk

You want to read the map there should be 5 locations near the house site area with a number, this is your seasonable high water table. It needs to be 2' to not have a mounded system, but with the grade of the property which is the 8-15% you may still need a slightly mounded system if it is right at 2'. Just because there is are existing septic and well doesn't mean they work properly. Well and Septic should be 100' from each other. Slab should be 3' above the seasonable high water table. If water table is at 2' or less you will bringing in sand and clean fill. Basement will be above grade. At least by NJ standards. Garage under design works well with high water table and basement above ground. If property slopes correctly you could get a walk out basement. Sent from my XT1585 using Tapatalk

I don't think I'm understanding completely but for one you can pipe your sink around the first floor walls til you get to a location where you can drop down into the basement without crossing the stairs. You are allowed to use automatic air admittance valves for vent now in NJ (not on sewer ejector) Must be a Studor type vent not the little cheesy ones. Sent from my XT1585 using Tapatalk

Give it up we proved it is Pork Roll. Taylor Ham doesn't exist. Debate over Sent from my XT1585 using Tapatalk

That's impossible with all the firearms laws we have in NJ. How could a prohibited person have a firearm? How could anyone have an illegal assault weapon? How could there be loaded firearms in a vehicle? Oh that's right criminals by nature don't follow the law. Just another example of how ineffectual gun control laws are. Sent from my XT1585 using Tapatalk

I'm sorry but that is not being muzzle swept. I guess you never went to the old Brick Armory? When some moron on the line turns around to talk to his friend, swinging around his loaded pistol, that qualifies as muzzle swept. Went a few times after that, but always mid morning during the week when no one was there. Sent from my XT1585 using Tapatalk

I guess I will wait to call. Didn't have time to call yesterday Sent from my XT1585 using Tapatalk

Their message says to call them if you haven't received anything after a month. A month came and went last week. Sent from my iPad using Tapatalk

I am in the same boat. My first application was lost. Sent in second 2 days before you. Also showed delivered to PO BOX. I called right away. They confirmed receipt, but still no check was cashed. Going to call again tomorrow. Sent from my iPad using Tapatalk

Yes. PA could care less about NJ Draconian laws. Only reason buying non compliant rifle is an issue is because of Federal NICS check and Federal licensing. If the rifle is legal in PA it can remain in PA and no one is going to bother you. Sent from my XT1585 using Tapatalk

They were referring to ones already legally owned. Sent from my XT1585 using Tapatalk

No reason to sell to gun store today unless they are going to pay you near market value. Even though I can't stand owners and mods gunboards has the most action on the trader, PAFOA is another good one, and of course the Ruger Forum as recommend. This forum for long guns is great but handguns may not be the best but it can't hurt to list it on all of them. Just post in listings it is cross posted. Sent from my XT1585 using Tapatalk

Try Remixer on the forum here. Steve from Monmouth Arms. Sent from my XT1585 using Tapatalk

Too late for that My first application was lost in mail. Second one sent July 27th Priority Mail. Called August 5th to confirm they got it because tracking said sent to PO Box. Going on 3 weeks no check cashed. Did they call references? I sent with Utah & Florida CCW copies plus NJ FID copy. Hopefully that didn't cause an issue. First time didn't send NJ FID but read others who were approved did so second time I included it. Sent from my XT1585 using Tapatalk

Actually there was not. I used a card I had only used at PSA and local Chinese Restaurant, nowhere else. Then when I got the replacement card I used it only at PSA. Again card stolen. It was likely an employee at PSA, not the company itself, but I won't buy from them again. SG Ammo has better prices. The quality of PSA rifles is sub standard at best IMO. Many others feel the same way. Check out Calguns and see how many PSA Rifles sit unsold. When a Stag or other decent AR type comes up for sale they sell rather quickly. Maybe their higher end line is ok, but if you ever go to resell it how many people are going to know the difference or bother looking into it? Many see PSA and just move on. Sent from my XT1585 using Tapatalk

Tanners in PA has best selection. They also sell on gunbroker, but go in person. Their gunbroker listings are a little shady at times. For instance they were selling a 1935 Brazilian Mauser as an Embassy Rifle. In reality it was a 1935 barreled action with 1908 and 1912 parts. Sent from my XT1585 using Tapatalk

I will get one eventually but not while I live in this communist state. It has to be very annoying to break ammo down into 15 round strips. Sent from my XT1585 using Tapatalk

Nice looking Yugo do numbers match? Sent from my XT1585 using Tapatalk

If the Tavor is a thumbhole stock and not a pistol grip than you can have a flash hider. Not really sure if that is a thumbhole stock, but if NJSP say so a thumbhole stock it is. Sent from my XT1585 using Tapatalk

It only takes an hour and a half to convert.....if you put it together right the first time. Couple tricks I learned are use a rubber band to tie off the hammer springs, otherwise they will bite you. Make sure the hammer is in the correct way, springs are fully wound (3x), and on the correct side of the hammer. Hammer has to go in first. Tie fishing line around the bolt hold open spring, feed the line through the bolt hold open slot, pull down hard and maneuver in place with a thin hook. It helps to have a third hand ready to put the pin back in. After pin is in just pull real hard and snap off the fishing line. Here are my conversions. Russian AK-74 clone and East German MPi-KM clone. This is the extra Original Russian Sunburst AKM Stock set I have. Just needs the hand guard clips and gas tube. Pistol Grip screw, butt plate, and swivel are all there. Was going to do a third but with current prices two is enough. For the gas tube and clips go to http://www.robertrtg.com/store/pc/Gas-System-c35.htm?pageStyle=h&ProdSort=3&page=3&idCategory=35&viewAll=yes For NJ Legal magazines http://www.charliecoopers.com/rifle-magazines/7-62x39/ t They shipped quick and they have every magazine you can think of blocked to 15 with epoxy floor plate. If you go with foreign made furniture you will need American Made Mags to be 922r compliant. The Magpuls in 7.62x39 I got to work flawlessly with and without the bullet guide. Just need to file down the lip on the back. The Tapco 5.45 Mags work without need for a bullet guide. The conversion parts (FCG, Trigger guard, lower hand guard retainer, bullet guide) I got them from http://www.dinzagarms.com/ Great customer service and parts have held up. Go with the deluxe conversion kit this way you can bend the existing trigger guard and cut the rivets with a grinder. Sent from my XT1585 using Tapatalk

Surprisingly Easton has many good restaurants. Haven't heard of Pop's but next time I am up that way I will give it a try. Any place that serves scrapple and pork roll (not Taylor Ham) must be good. Sent from my XT1585 using Tapatalk

Best insurance I found. Coversall firearms no matter where they are located and only had to itemize those over $10k in value. Got a $50k policy for $157 per year. [email protected] Sent from my XT1585 using Tapatalk