Skip to content
View in the app

A better way to browse. Learn more.

New Jersey Gun Forums

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

To build or not to build? What benifits me

Featured Replies

Hey guys,

 

After doing endless research and almost getting an p.a.pa AK, i decided the .556 would be the way to go. Which brings me to deciding do i settle for a S&W M&P15FT because its the only NJ legal thing i can find... Or do i buy a complete upper and complete lower and figure out how to piece it together... Which im sure there are youtube videos with instructions so im not worried about it.

 

Part 2 is in my research i found certain specs i must get

1/7 twist

556 over .223

chrome lined barrel

NJ LEGAL

 

 

With great hopes the build should come out to $650

 

i have been looking into cmmg...

 

Where do i go from here??

Putting together a complete upper and lower takes about 15 seconds.

 

1:9 twist will stabilize up to 64gr without a problem. The cheapest ammo is usually 55/62gr. 1:7 is certainly good if you want to go to a heavier bullet but I wouldn't get too hung up on it. You're not going to be shooting match grade ammo sub moa out to 300 yards at a cmp match with a $650 carbine.

 

5.56 chambered rifles are certainly more flexible.

 

Chrome lined, also good

 

NJ legal is certainly required.

 

Add it all together and you to can be a dreamer for $650. The reality is that you're a bit low on your estimate.

 

You can get the S&W Optics ready carbine for around $650 but then you're going to get a muzzle break pinned on and have the stock pinned. Thereafter you'll need to get some optics. You can probably get something from DPMS NJ legal for $850 or so. I've not checked prices recently, it may be a bit cheaper.

 

I have no opinion on cmmg but just checking their website, the cheapest upper I see is $575 + 200 for a lower and you're looking at $850 after tax and nics.

 

you can get a Bushmaster XM15-ES2 M4 A3 Optics Ready Carbine complete(Same as your specs except 1:9) for under $950 out the door but then you need an optic too.

 

You might be better off picking up something used that way all the work, tax and NICS are already done.

Check out Delton they do some pretty nice builds that are NJ compliant and you can pick the features you want. The barrel assemblies page shows a bunch of choices. You are probably leaning towards the M4 set up with the 1/7. M4 Page

 

Among my AR's, I have 2 RRA's that have 1/8 Wylde chambered which I think is the best twist for 55 to 77g pills. For HD, I have TAP 75's and at close range, the twist difference between 1/7 and 1/9 shooting 55's to 75's isn't going to come into play at 10 yards. My rainy day supply of Zombie rounds are 69g OTM's which shoot well in both 7/9's. The 69's are insanely accurate out to 300yards even with a stiff wind and a 1/9 twist. I use them shooting service rifles (RRA's) at 200yard and if windy, I'll switch to 77's at 300y. Anything under 50yards is going to be about technique and not twist or bullet weight.

X2 on Delton

Take one of these with the options of your choice (and NJ legal) http://www.del-ton.com/ar_15_kits_s/1.htm (personally I would go with the 16" midlength)

Then add a stripped lower like this http://www.aimsurplus.com/product.aspx?item=F1SASL&name=Surplus+Arms+%26+Ammo+LOW15+Stripped+AR+Lower+Receiver&groupid=53 or this http://palmettostatearmory.com/1560.php

Than you just assemble the lower, drop the upper on and go have fun :ph34r:

Putting together a complete upper and lower takes about 15 seconds.

 

1:9 twist will stabilize up to 64gr without a problem. The cheapest ammo is usually 55/62gr. 1:7 is certainly good if you want to go to a heavier bullet but I wouldn't get too hung up on it. You're not going to be shooting match grade ammo sub moa out to 300 yards at a cmp match with a $650 carbine.

 

5.56 chambered rifles are certainly more flexible.

 

Chrome lined, also good

 

NJ legal is certainly required.

 

Add it all together and you to can be a dreamer for $650. The reality is that you're a bit low on your estimate.

 

You can get the S&W Optics ready carbine for around $650 but then you're going to get a muzzle break pinned on and have the stock pinned. Thereafter you'll need to get some optics. You can probably get something from DPMS NJ legal for $850 or so. I've not checked prices recently, it may be a bit cheaper.

 

I have no opinion on cmmg but just checking their website, the cheapest upper I see is $575 + 200 for a lower and you're looking at $850 after tax and nics.

 

you can get a Bushmaster XM15-ES2 M4 A3 Optics Ready Carbine complete(Same as your specs except 1:9) for under $950 out the door but then you need an optic too.

 

You might be better off picking up something used that way all the work, tax and NICS are already done.

I assembled a couple DPMS's last year for $700 - $750 if your not looking for match grade components. Bought the compliant uppers complete and assembled the lower and the stock.

  • Author

Now i am assuming that all lowers are nj legal that are semi auto... but which uppers are nj legal? it seems like they all have the flash hiders...

 

but on another note, i am allowed to have 1 but not 2 of the "Evil features" right or wrong?

One evil feature for an AR. Usually a pistol grip. A detachable mag is a qualifier for the AWB, not an evil feature. So no flash hiders/suppressors, threaded barrels, bayonet lugs, folding or collapsible stocks.

collapsible mags.

 

Awesome! Where can I get one? :icon_e_biggrin:

You misquoted me. :icon_e_confused:

 

Bah, you're a Post Post editor!

  • Author

Whats a good site that has these for good prices? (nj legal)

 

im looking on gun broker now

  • Author

I found my stag arms lower. i just need to find a post ban upper...Im having a really hard time with this

I found my stag arms lower. i just need to find a post ban upper...Im having a really hard time with this

 

You can buy any upper and then have it neutered to NJ specs. There are some vendors on this forum that do it, also ADCO in Ohio. I had an upper shipped to them, the pinned a break and removed the bayo lug. This generally more expensive, but you can choose the exact upper you want.

  • Author

Spike's tactical will remove the Bayo lug, add and pin a muzzle break but it'll cost you $620 http://www.spikestactical.com/new/z/spikes-tactical-16-lightweight-le-upper-556-p-467.html

 

 

This thing is beautiful... And has everything i asked for. This is a little above the upper budget, i wonder if there are any a little less?

  • Author

Stag Arms Stripped AR-15 Lower Receiver, 5.56mm Marked

http://www.smallarmsales.com/Stag_Arms_Str...mm_p/stag01.htm

$109.99

 

Spike's Tactical 16" Lightweight LE Upper

http://www.spikestactical.com/new/z/spikes...-556-p-467.html

$620

 

AR-15 Complete Lower Parts Kit

http://www.del-ton.com/AR_15_Lower_Parts_Kit_p/lp1045.htm

$55

 

I have almost every tool ever made, just not gun smithing tools so im not worried about that.

 

And i wish i could find a less expensive NJ legal upper, im going to have to sell alot of cars to get $600 lol

 

But most importantly...Am i missing any parts? or is this everything i need?

All you need now is magazines and ammo!

  • Author

All you need now is magazines and ammo!

 

 

lol i forgot about the mags... Can i do 15 rds (if i can find them?

I don't see a buffer tube/spring and stock.

I don't see a buffer tube/spring and stock.

 

Thanks Mark, I missed that one!

I used this lower build kit http://palmettostatearmory.com/598.php but because its a collapsable stock you HAVE to pin it in place to be Jersey legal. That was the first thing I did as soon as I got it. It went together great with this lower http://www.aimsurplus.com/product.aspx?item=F1SASL&name=Surplus+Arms+%26+Ammo+LOW15+Stripped+AR+Lower+Receiver&groupid=53

Jcirillo, I have a pinned M4 stock that you could have if you want it. It'll complete your build. PM me if your interested.

  • Author

So i ended up gettin a M&P 15 Lower... for $120...

 

I figured as long as theyre aluminum, lets get the one with the coolest logo on it

  • Author

Last but not least is this a complete upper? or am i missing anything?

 

 

 

 

http://www.spikestactical.com/new/z/spikes-tactical-16-lightweight-le-upper-556-p-467.html

 

OR-------

 

Item Name: 16" Mid-Length Custom Upper

Item Price: $500.00

Options:

# 16 Custom Upper -ML Barrel:DTI 16" 1x7 Mid-Length Chrome Lined Heavy Barrel

# Custom Upper -BC:Standard Bolt & Carrier

# 16 Custom Upper -ML Handguards:Mid-Length Handguard with Heat Shields

# Custom Upper -Gas Block:A2 Front Sight - No Bayonet Lug

# Custom Upper -Flash Hider:Phantom Aggressive End Comp/Brake- Pinned & Welded

# Custom Upper -Upper:Flat Top Upper with M4 Feed Ramps

# Custom Upper -Charging Handle:Standard Charging Handle

# Custom Upper -Carrying Handle:None

 

http://www.del-ton.com/ProductDetails.asp?ProductCode=CU104&CartID=1

 

Do i need anything else to complete it? (BOLTS,

 

IM LOOKING FOR THE WORD FIRING PIN, BUT I DONT SEE IT ANYWHERE

 

HELP!!!! PLEASE

Last but not least is this a complete upper? or am i missing anything?

 

 

 

 

http://www.spikestactical.com/new/z/spikes-tactical-16-lightweight-le-upper-556-p-467.html

 

OR-------

 

Item Name: 16" Mid-Length Custom Upper

Item Price: $500.00

Options:

# 16 Custom Upper -ML Barrel:DTI 16" 1x7 Mid-Length Chrome Lined Heavy Barrel

# Custom Upper -BC:Standard Bolt & Carrier

# 16 Custom Upper -ML Handguards:Mid-Length Handguard with Heat Shields

# Custom Upper -Gas Block:A2 Front Sight - No Bayonet Lug

# Custom Upper -Flash Hider:Phantom Aggressive End Comp/Brake- Pinned & Welded

# Custom Upper -Upper:Flat Top Upper with M4 Feed Ramps

# Custom Upper -Charging Handle:Standard Charging Handle

# Custom Upper -Carrying Handle:None

 

http://www.del-ton.com/ProductDetails.asp?ProductCode=CU104&CartID=1

 

Do i need anything else to complete it? (BOLTS,

 

IM LOOKING FOR THE WORD FIRING PIN, BUT I DONT SEE IT ANYWHERE

 

HELP!!!! PLEASE

 

 

That delton looks like a good deal. May get one.

 

Do i need anything else to complete it? (BOLTS,

 

IM LOOKING FOR THE WORD FIRING PIN, BUT I DONT SEE IT ANYWHERE

 

HELP!!!! PLEASE

 

Includes

16", 5.56 chambered mid length barrel, 1x9 Twist, Chrome Molly or Chrome Lined

upper receiver

bolt and carrier assembly

handguards

flash hider

Yes it should a complete upper w/ everything but a rear sight, but I would still call them to confirm

  • Author

Someone mentioned to me that i need to get a buffer tube assembly. Is that true?

Someone mentioned to me that i need to get a buffer tube assembly. Is that true?

 

Its in the mail dude, shipped yesterday.

  • Author

Its in the mail dude, shipped yesterday.

 

The buffer too? Ray your the best!!!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Recently Browsing 0

  • No registered users viewing this page.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.