Skip to content
View in the app

A better way to browse. Learn more.

New Jersey Gun Forums

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Possible Issue w/USA Ammo New 9mm 115g Lot#16081130

Featured Replies

Here's another thought. I have never used or examined this ammo, so I may be barking up the totally wrong tree. Something the OP said struck a chord. He was describing the surface of the bullet as looking mottled/wrinkled/dimpled, call it what you will, but not what we are used to seeing with a truly jacketed bullet.

 

Is there a chance that these bullets are actually cast and then plated? If thats the case, they may be going directly from the mold to the plating process without being consistently sized. What is even more likely, if the above is true, something may have gone wrong in the casting process (molds not up to temp for one thing) and there may be voids in the bullets, resulting in an imbalance concentrically, resulting in the keyholing.

 

Undersized still makes more sense, but it isn't the only possible cause. If you are really going to delve into this, I suggest you section a bullet also.

 

Adios,

 

Pizza Bob

  • Replies 74
  • Views 7.7k
  • Created
  • Last Reply

Top Posters In This Topic

Most Popular Posts

  • Yup, down to just over 1K of .380 left, went through about 3500-4000 rounds of USA ammo and no issues. Also the 9mm ammo I have from them, never an issues with well over 5K through my G19 and now feed

Posted Images

Damn, this is getting complicated.

 

 

 

You're about a 40min ride...whats your sched look like tomorrow? I'm on nights this week and next so any time before 12 would be good. Appreciate the offer.

 

 

EDIT: Still no reply back from USA Ammo. I sent a follow up email. Also tried calling again w/o an answer.

 

Your best bet is to break each down and do a proper measurement....I can be there in the AM tell me what time....

 

Me best guess is the OAL is not causing the keyholing...bring a selection of ammo from USA and we need to break them down and look at the bullets themselves....my guess is you will not find consistency with them...and will be slightly if not dramatically undersized...

 

I had this same problem with an enfield rifle as the bore was .314 and the (cast) were sized and lubed at .311....in lieu of .313 bore that being the standard they hoped for.

  • Author

Heres something interesting. Looks like USA Ammo pulled the new 9mm 115g FMJ off their site. When I try to use the direct link to the page via my history, it redirects me to the Home page. Unless they're out of stock and removed the page?

 

Heres whats offered in their 9mm

http://www.usaammo.com/9mm-C8.aspx

 

Another thing, when I try to call the main number on their site 218-464-4776, it gets forwarded to a different number 936-366-6777 with a generic not available msg.

 

 

Here's another thought. I have never used or examined this ammo, so I may be barking up the totally wrong tree. Something the OP said struck a chord. He was describing the surface of the bullet as looking mottled/wrinkled/dimpled, call it what you will, but not what we are used to seeing with a truly jacketed bullet.

 

Is there a chance that these bullets are actually cast and then plated? If thats the case, they may be going directly from the mold to the plating process without being consistently sized. What is even more likely, if the above is true, something may have gone wrong in the casting process (molds not up to temp for one thing) and there may be voids in the bullets, resulting in an imbalance concentrically, resulting in the keyholing.

 

Undersized still makes more sense, but it isn't the only possible cause. If you are really going to delve into this, I suggest you section a bullet also.

 

Adios,

 

Pizza Bob

Yes, the bullets actually appear to be what you described...cast then plated. But I'm no expert.

 

Your best bet is to break each down and do a proper measurement....I can be there in the AM tell me what time....

PM Sent.

  • Author

Come by the shop and let me know when you plan to and we can break it all down

Hey Nick, still good for 1pm?

Pull multiple bullets. Weigh them and measure them (diameter). Then section them and determine if they are jacketed (copper cup drawn around a lead core) or plated - should be obvious by the thickness of the covering. If jacketed, check for uniformity of jacket thickness and gaps between core and jacket. If cast and plated, look for casting voids in the lead. This is a good beginning - if this reveals nothing, maybe USAammo will replace your batch and test the ones you send back.

 

Perhaps what is more troubling is their (USAammo's) lack of response. As I recall, they were very responsive to the AR KB and not only made good on the rifle, but came clean on what the cause was. Despite their name, I believe that, at least some, of their components used in the manufacturing process are sourced from other than the USA. I believe the powder that caused the AR KB was one such component.

 

Good luck.

 

Adios,

 

Pizza Bob

Perhaps what is more troubling is their (USAammo's) lack of response.

 

 

Did you see Frank's post about them? Could just be that they're getting hammered from all sides right now with issues because of their statement in their last email ad?

Did you see Frank's post about them? Could just be that they're getting hammered from all sides right now with issues because of their statement in their last email ad?

 

 

Ahem....it was my post. I'm not sure when that ad was sent, but I got the impression that the ammo inquiry pre-dated the release of the ad - but I'm not on their mailing list.

What was in the email 11/28?

 

Oop sorry - credited the wrong old guy :D

 

And I am on their mailing list - I got the email on 11/28.. Looks like Joe opened communications (or attempted to) with them on 11/29.

The USA Ammo loads look like they are using plated bullets made of swaged lead wire. If they have lots of pock marks, it probably means they are one of the softer varieties. My guess is they are either undersized from the source, or undersized by the manufacture process, and that is causing them to keyhole.

  • Author

So I just got back from Mastodon, Nick and the crew were very helpful. Whacky group in an awesome way lol. What we came up with is the USA Ammo is much smaller at the OGIVE.

 

OGIVE:

USA .334/5

WWB .350

 

So it looks like this is the culprit. The bullets are FMJ, but just look to be of lesser quality. In a nutshell, hopefully USA Ammo will contact me back. Worst comes to worst, I'll pull all the bullets and have approx 400 primed casings waiting for my reload set up and never deal with them ever. Lesson learned.

 

 

And I am on their mailing list - I got the email on 11/28.. Looks like Joe opened communications (or attempted to) with them on 11/29.

My initial email was on 11/28. First phone call was 11/29. Follow up email and phone call was 12/1. Like I was tellin the guys up at Mastodon, at the very least contact me back acknowledging my concern(s) and say you're looking into it. Even if they're getting slammed, tell me that. Small communication is better than none at all.

So I just got back from Mastodon, Nick and the crew were very helpful. Whacky group in an awesome way lol. What we came up with is the USA Ammo is much smaller at the OGIVE.

 

OGIVE:

USA .334/5

WWB .350

 

So it looks like this is the culprit. The bullets are FMJ, but just look to be of lesser quality. In a nutshell, hopefully USA Ammo will contact me back. Worst comes to worst, I'll pull all the bullets and have approx 400 primed casings waiting for my reload set up and never deal with them ever. Lesson learned.

 

 

Wacky is WAAAAAAAAAAAAAAAAY to kind.....Nutjobs are more like it....its an eclectic crew... :icon_mrgreen: Today was CALM too...but the coffee, conversation and work is all good....

 

The USA ammo is undersized....BUT you do have the brass and primers....I would also try to find what powder they used...BUT given their QC I wouldn't trust what they say...a shame to waste all that pull down powder... HOWEVER, not knowing what primers they used as well...WHATEVER you do load....load on the low end of the tables and do some and check the function etc...

 

I think you should be ok, BUT YMMV......

 

hey you also got a freebie quickie .....ultrasonic cleaning that is.... :sarcastichand:

 

Glad you came by and nice to have met you !

I'm confused. How are you measuring bullet diameter at the ogive? The ogive is a constantly diminishing diameter. The bullet should have been pulled and measured at the base or close to it - the part that goes into the neck of the case. I hope we're just dealing with semantics here. If the major diameter is only .334" then yes, I'd say that's the problem. Please clarify.

 

Adios,

 

Pizza Bob

  • Author

No, that tool you mentioned wasn't used. Theres no denying this ammo is FUBAR. At this point I shouldn't have to tell an ammo manufacturer whats wrong with their ammo. After my initial email they should of acknowledged my concern(s) and request to send some of the ammo back so they could look, and then go from there. This may be the wrong approach but its how I feel. At this point the actual ammo isn't the main concern anymore. Whats more concerning is, after a week, there still have been no attempts at any customer service.

 

Now think of this. What if something happened and I actually had to depend on this ammo to save my and/or my family's life. Judging by the first pic I uploaded theres no way to think I could ever depend on any accuracy. This was the first time trying this ammo and I will never use this ammo again. Its just not worth the risk.

You cant measure from ogive without a comperator, so either you did use a comperator or you didnt measure from the ogive lol.

  • Author

You cant measure from ogive without a comperator, so either you did use a comperator or you didnt measure from the ogive lol.

Ok, I'm just going by what Nick said lol...that they're undersized. Possible that or a combination of things causing the issue.

You cant measure from ogive without a comperator, so either you did use a comperator or you didnt measure from the ogive lol.

 

 

Glenn, you are :thsmiley_deadhorse: . Measuring the ogive isn't real relevant in this case. Just looking for undersized bullets that would allow some yaw in the freebore, before hitting the rifling, that would result in a destabilized bullet when it exits the barrel. If these were truly measuring .334" or .335" at the major diameter, then I would have to think that's the cause of the keyholing.

 

I'm also wondering if Krdshrk isn't onto something. They may very well be swamped with e-mails since entering into their controversial e-mail ad campaign. Chances are the OP's e-mail got burried in the torrent. They were very responsive to the KB issues with the AR's.

 

Adios,

 

Pizza Bob

  • Author

I'm also wondering if Krdshrk isn't onto something. They may very well be swamped with e-mails since entering into their controversial e-mail ad campaign. Chances are the OP's e-mail got burried in the torrent. They were very responsive to the KB issues with the AR's.

Is there another issue going on at the same time that I missed? What controversial email ad campaign? Two emails and two phone calls w/o any kind of acknowledgement. The phone calls get forwarded to a diff number with a generic vm box. Not even a msg saying "You reached USA Ammo...." Theres another thing I did to try and contact them(still no reply), but I'm waiting to say anything incase they get wind of this thread lol.

On a phone....hard to type....the bullet is undersized...

 

OAL...IS NOT the problem...per see...they are seated a bit deeper

 

Comparator will measure OAL from the ogive...

 

But if you take that location and measure from there to the base they are undersized

 

Comparatively speaking the angle of the bullet shape from the ogive to the point is sharper that my bullets from midway..our his Winchester ammo...

 

The undersuse coupled with possibly a short freebpre to the lands/grooves...imho is causing the bullet to either engage the rifling lightly if at all and possibly at a non centered angle...causing the keholing large groups pattern...

 

Whatever the cause they'd particular batch of ammo is bad...

I'm getting to this tread late but I must have got lucky. I too bought 500 rounds of USA 9mm new ammo during the Gearhog promo and have gone through all without incident. Holes on paper are true,clean and round through 2 pistols.I've read through the whole tread but don't know if the OP purchased new or reloads.

  • Author

I've read through the whole tread but don't know if the OP purchased new or reloads.

Really? lol

 

Whats up all...couple of months back I purchased 500 rounds new 9mm from USA Ammo.

Really? lol

Alright ...alright I missed that. Then I must really be lucky huh?
  • Author

Alright ...alright I missed that. Then I must really be lucky huh?

Maybe lucky, or maybe they normally put out a good product and my first experience is a bad one, I don't know. Not only did I get a bad batch of ammo, they've yet to make any efforts in contacting me back. At this point I don't expect them to either. Once my bullet puller comes in I'll break em down and keep the primed brass. I'll be sure to let my experience be know as much as and whereever I can.

Maybe lucky, or maybe they normally put out a good product and my first experience is a bad one, I don't know. Not only did I get a bad batch of ammo, they've yet to make any efforts in contacting me back. At this point I don't expect them to either. Once my bullet puller comes in I'll break em down and keep the primed brass. I'll be sure to let my experience be know as much as and whereever I can.

 

It's a damn shame to toss all that powder...................................

It's a damn shame to toss all that powder...................................

 

But who knows what the heck it is? It is probably not something available to handloaders. That was part of the problem with the AR KB's. His powder source (not domestic, IIRC) changed something without telling him.

 

 

But who knows what the heck it is? It is probably not something available to handloaders. That was part of the problem with the AR KB's. His powder source (not domestic, IIRC) changed something without telling him.

 

Agreed...you CANNOT TRUST IT...but it's still a shame

  • Author

So here is an update. Finally after persistent phone calls throughout everyday, I finally reached a human..I think. Talked to a guy named Steve, he mentioned that they have been extremely busy filling orders while they change suppliers. He asked for my info and what was happening with the ammo, I then started to stat that they have 4 emails stating this info. But I digress, gave him the info, he looked up my order, told him what was going on, then he said that his boss was out for the day and that I should be getting a call back "in the early part of next week." I kept asking who would I get the call from and at first it seemed like he didn't want to give me his boss' name, by the 3rd time I asked he finally gave me a name of Robert. So, I will give them till next Wed noon time...after that I'm writing a script at work to have my phone call there every 30 seconds till someone picks up lol.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Recently Browsing 0

  • No registered users viewing this page.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.