Skip to content
View in the app

A better way to browse. Learn more.

New Jersey Gun Forums

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

my poor mans primer depth / over travel handle stop XL650

Featured Replies

I shoot a lightened action revolver which works best with federal primers seated between .008 and .010.

 

Now unfortunately the xl650 doesn't have any sort of depth adjustment for seating primers, and I have a problem either over seating them by pushing too hard, or to shallow by not pushing hard enough. which would result in light strikes

 

Brainstormed a little bit today and came up with this, an adjustable over travel stop for the handle. made of some scrap pieces of steel I had in the garage. 

 

I knocked out 50 or so pieces of brass and measured each one... Way more consistent .008-.009 typically(PPU head stamp which I have a metric ton of ) , but federal likes to seat a touch shallow at around .0065-.007ish, so does winchester. 

 

 

Yes, it's ugly, Yes I know the welds suck, Yes I know revolvers are stupid.

 

But - here it is... let's just call it still in it's " prototype stage " 

 

-alec

 

9258668496_300597fc8c_h.jpg

 

The only issue now is it in the way of the ammo tray, - just notched it out and proped it up on 2 primer boxes and she's good to go. I'm going to try to come up with some sort of extension piece for the ramp so I can have the tray sit a little farther away.

 

9258667274_f4650919c3_b.jpg

 

In action:

 

Did you cut out the bullet bin or use your teeth? ;)

Well, since its in prototype stage, you might want to go to a fine thread bolt.  You will get better precision on adjustment.

Did you cut out the bullet bin or use your teeth? ;)

Lmao!!

I shoot a lightened action revolver which works best with federal primers seated between .008 and .010.

 

Now unfortunately the xl650 doesn't have any sort of depth adjustment for seating primers, and I have a problem either over seating them by pushing too hard, or to shallow by not pushing hard enough. which would result in light strikes

 

Brainstormed a little bit today and came up with this, an adjustable over travel stop for the handle. made of some scrap pieces of steel I had in the garage. 

 

I knocked out 50 or so pieces of brass and measured each one... Way more consistent .008-.009 typically(PPU head stamp which I have a metric ton of ) , but federal likes to seat a touch shallow at around .0065-.007ish, so does winchester. 

 

 

Yes, it's ugly, Yes I know the welds suck, Yes I know revolvers are stupid.

 

But - here it is... let's just call it still in it's " prototype stage " 

 

-alec

 

9258668496_300597fc8c_h.jpg

 

The only issue now is it in the way of the ammo tray, - just notched it out and proped it up on 2 primer boxes and she's good to go. I'm going to try to come up with some sort of extension piece for the ramp so I can have the tray sit a little farther away.

 

9258667274_f4650919c3_b.jpg

 

In action:

 

Yes on all counts, but it is a pretty cool idea. Nice work Alec!

  • Author

 

 

Yes on all counts, but it is a pretty cool idea. Nice work Alec!

haha, thanks

Did you cut out the bullet bin or use your teeth? ;)

Looks like he used a percision cutter by H&R 410 model with a fine cutting blade #8

 

Nice job bro... 

The video would be better with explosions.

 

But otherwise nice job.

 

Stuff like this makes me shake my head.  As you know I'm a noob reloader and would never have considered the depth at with to set primers.  I've had some trouble with them sitting high and realized that nut that holds the spring and primer plunger (for lack of a better term) had loosened up.  Once I put a wrench to it my primers are now seating better.

 

So much to learn.

  • Author

The video would be better with explosions.

 

But otherwise nice job.

 

Stuff like this makes me shake my head.  As you know I'm a noob reloader and would never have considered the depth at with to set primers.  I've had some trouble with them sitting high and realized that nut that holds the spring and primer plunger (for lack of a better term) had loosened up.  Once I put a wrench to it my primers are now seating better.

 

So much to learn.

 

 

No worries Mike, you'll pick up knowledge as you go along, it's not rocket science. But yes, make sure your primer seater is tight, I use an open ended wrench to get up in there... It's tight, so you can only do maybe a 1/4 turn at a time - but it'll get there.

 

 

For the everyday reloader shooting factory / stock guns you wont have problems, Though since I like to shoot modified revolvers they work best at a more specific primer depth range, which previously was hard to control.

Yeah Mike for you and your sons gun it won't be as critical. My M&P goes bang with CCI's every time, and that's with an Apex kit in it. Like Alec said it's mostly the revo's where this becomes a factor. 

My M&P is rather picky.  Andrew had some real issues during the last steel match due to high primers.  My Beretta with eat them, but the M&P is a touch more finicky.

 

I've repressed all the primers now and they sit where they should so we should be good, but man was that a pain. 

My M&P is rather picky.  Andrew had some real issues during the last steel match due to high primers.  My Beretta with eat them, but the M&P is a touch more finicky.

 

I've repressed all the primers now and they sit where they should so we should be good, but man was that a pain. 

But his M&P was a tad more accurate than your Beretta. :taunt:

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Recently Browsing 0

  • No registered users viewing this page.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.