Skip to content
View in the app

A better way to browse. Learn more.

New Jersey Gun Forums

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Whats the best way to deprime over 12k of 9mm brass

Featured Replies

What would be the best way for the fastest most inexpensive way to deprime over 12k of 9mm brass?

 

 

  • Replies 60
  • Views 8.6k
  • Created
  • Last Reply

Top Posters In This Topic

Ask a neighborhood kid if he wants to earn $10.   :sungum:

Call a friend with a Dillon 650 equipped with a case feeder

Ask a neighborhood kid if he wants to earn $10. :sungum:

I was about to make the same suggestion! B)
  • Author

Ask a neighborhood kid if he wants to earn $10.   :sungum:

just give him a hammer and a punch? lol

 

 

I don't have any equipment yet,

With that much brass, I would contact a commercial reloader and make a deal!

If you average 1 case every 3 seconds, you could do it yourself in 10 hours!

  • Author

That's just the 9mm I hoarded over the years, lol

 

I got lots more of other calibers

What are you doing with it?

 

I have a LOT of brass in .45 and .38. I just deprime a few hundred at a time. I load on a single stage.

install a few decapping dies in a progressive press with case feeder - whole job should take about 12hrs. don't forget to lube and check the pins every hour or so

install a few decapping dies in a progressive press with case feeder - whole job should take about 12hrs. don't forget to lube and check the pins every hour or so

What's the point of installing a few decapitated dies in a progressive ? You only need one.

 

That being said, find somebody with a auto drive on a 1050

Get started...?

 

Seriously, pay a kid or just sit down and git'er done!

 

Good luck. I find the prep to be the most tedious.

 

C

I'll do it for you. I charge a fee of 1 case per primer removal

I'll do it for half the brass

I wouldn't deprime 12k cases and stop there, facing the ordeal of then loading 12k rounds.

 

Bite the bullet, so to speak, buy a progressive press, and start loading. At least then with every pull of the handle you are rewarded with a loaded round.

I agree with 10X. Why do you want to just deprime them?

I've done 1M at a time on a progressive press. About an hour and 15 to hour and a half, over 12 days and your done.  Some jobs are better tackled in small batches over time to keep morale up.  Then off to the tumbler.  Sometimes I just keep them in a sealed bucket and pull them out as I need them. They don't eat or drink nothing so just hold on to them.  Cash in hand sort of.

look like it's time to spend some money and buy a press -- gonna need it anyway

 

Are they clean or dirty? -- if clean then you can size and deprime at the same time --

 

if dirty and you want to wet tumble then deprime with a decapping die and tumble -- I'll be making tumblers again very soon if interested -- with an 8" drum you could tumble those 18 pounds at a time

 

a case feeder on a progressive press will take some of the pain away but it really isn't necessary -- just get started

I've got one of these....put a 9mm carbide sizing die in it, and while you're watchin tv or the computer etc...you can be decapping all that brass

 

http://www.midwayusa.com/Product/410804/lee-hand-press

 

 

^^^^ This ^^^^^ while watching "The Walking Dead" on Sunday nights......  It will get you in the mood for season 9 (oops, spoiler from the books :-)

 

 

I just bought a universal Lee de-capping die and use it for all kinds of brass before tumbling.  keeps you from breaking a more expensive sizing die when decapping crimped primers.  if you break on of those, it is only about $1.50 to replace the decapping pin.

 

 

As an aside, you can also try to resize your old military surplus .30-06 brass with it and you won't have to go the gym anymore!

Just to add --- The Hornady LNL will catch every spent primer you knock out -- all other press I have tried will drop a few...

 

My LNL puts primers in a 2 liter pepsi bottle under my bench

I've done 1M at a time on a progressive press. About an hour and 15 to hour and a half, over 12 days and your done. Some jobs are better tackled in small batches over time to keep morale up. Then off to the tumbler. Sometimes I just keep them in a sealed bucket and pull them out as I need them. They don't eat or drink nothing so just hold on to them. Cash in hand sort of.

Agreed doing them all at once would be painful.. do like 1k then clean as needed going forward.
  • Author

I'm not looking to do all in one sitting, just want ideas of inexpensive efficient setup

Sell the brass to a commercial reloader - by a reloading set-up and start over. If you don't intend to start reloading, make a deal with a commercial reloader for x number of cases - or x lbs of brass - per box of loaded ammo.

 

Adios,

 

Bob

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Recently Browsing 0

  • No registered users viewing this page.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.