Everything posted by lunker
-
denied extension on permit?
I would be sure to let the chief personally know that you have escalated the matter to the State Police. If you have a Representative or State Senator that will listen to you, I would make a complaint there too, and let the chief know this too. It would be good to see him feel some heat for his unwarranted and arbitrary decision.
-
1911 mags, what's the deal?
Ray, the original magazines for the 1911 had the seven rounders. Many of the more classic/less tactical 1911s still use them. My Colt Series 70 Repro came with two seven rounders. I believe there used to be (i.e. issue has been resolved though) reliability issues with 8 rounders. I don't know if it was that the extra round made it harder for bullets to be stripped from the mag as the slide went into battery, the different feed angle of the follower on the 8 round mags, or the different springs used in 8 round mags. I have seen mention of all of them, but this being the interwebs, don't know which (if any) were legitimate causes. As for current 1911 models, I personally go with 8 rounders from high quality manufacturers. I have yet to get a misfeed from my Chip McCormicks.
-
Saiga
Forum Price Request will almost certainly get you a better price than that.
-
Montana Gold order
Thanks Jon. That is a good brick-and-mortar price.
-
Anyone have problems with RWS 9MM Luger 124 Grain from WeaponsWorld
At the Bullet Hole? Shocking!
-
Montana Gold order
I just put an order in for Precision Delta and got some 230grain FMJ 45ACP. I would've had to order a case at MG, so I did save some money in the short run. I will let everyone know how I like these. I have always been really happy with Montana Gold products. I think the new anti-gunner scheme is to devalue our currency so much that we can't afford the reloading components.
-
SAF v NJ (MULLER et al v. MAENZA et al)
If the decision ultimately comes from a state court, yes. If it comes from the Supreme Court, NJ will throw up roadblocks, but in the end we willhave it.
-
Montana Gold order
Is the quality/accuracy difference enough to justify the cost difference between Montana Gold jacketed bullets and Berry's plated bullets? I do not use a heavy crimp or push my loads past 800-850 fps with 45ACP, so I am not exceeding the capabilities of the Berry's.
-
World Class Steel @ OBRPC 9/4/11
Will you have the munchies and be glassy eyed too?
-
Up with the big boys.
Cool. I wish i could've made it out today too. Too much house repair.
-
Alliance Power Pistol powder
The 10mm crowd loves Power Pistol for lighter weight bullets (155gr, 165gr, etc). I think there are good stout 357 loads for PP too.
-
Remington 1100 20 gauge
That should not be an expensive fix. Buy a choke ready Rem 1100 20 gauge barrel off GunBroker for $100 or take it to a gunsmith and have him thread the barrel for Rem chokes.
-
Montana Gold order
Bryan, I need some 230 grain CMJ 45ACP. I could use a case.
-
1911 mags, what's the deal?
I like wilson combat. lately I've been buying chip mccormick 8 round mags. they work great in my colt.
-
Remington 1100 20 gauge
I have the Rem 1100 Lightweight Magnum in 20 gauge. It is nice and light for the field, and the pheasants can't tell it's not a 12. Great gun.
-
Anybody like Country?
I dig the old country; Johnny Cash, Waylon, Hank, Patsy, George Jones. I like modern rockabilly.
-
Help deciding on next purchase
Taurus and Ruger are better at it though. Look for reports of Ruger or Taurus internal lock failure. If someone has a gripe, it always ends up on the internet. The lack of complaints about those two make me believe theirs is a better design.
-
US Military Aiming for a New Pistol to Replace the M9
I am surprised. I like Glocks, but I have always read that the Army and Air Force were the two military branches that insisted on external safeties on their sidearms.
- sights?
-
Help deciding on next purchase
So much for 44 special being a powder puff. That's a hot round. 44mag power in a short case. Watch out.
-
Help deciding on next purchase
It's easy. With the barrel muzzle pointing left, is there a tiny gaping hold just above the cylinder release button on the side of the frame? That is the lock. Also, the pre-lock revolvers usually came with a squarish fully finger contoured/checkered cylinder release button. The post-lock ones are smaller (top-to-bottom) and only have the finger contours/checkering on the top half.
- sights?
-
Wilson combat
There is a dealer there called Crazy John that has great prices on Les Baers. http://www.cj1911heaven.com/
- sights?
-
Help deciding on next purchase
Bob, I had been under the impression that the N frame 357s that came after the intro of 44magnum model 29 were the beneficiary of some frame strengthening (improved metallurgy) done to all N frames from that point on to help the gun hold up to the recoil of the 44mag. I have been searching the interwebs for confirmation, but nothing yet.