Everything posted by tony357
-
Handgun parts polishing...
you can polis the feed ramp, do not remove any material, IE change the ramp just polish it. leave the rest of the barrel alone. It may not need to be done!! unless it is out of the ordinary rough i have a thread on a S&W 22A i polished that i purchased.
-
Shotgun shells submerged by Sandy
where are you from hook?
-
USPSA OBRPC 2-24-13
Land on the roof top, That might get their ATTENTION !!
-
Powder choices
I have been using accurate # 2 and # 5 These propellants measure very accurate with my dillon square deal. #2 i am using in .45 with 230 gr FMJ #5 i am using in 9mm with 124 gr FMJ over 6.1 grains I have no trouble knocking down poppers with this load full size 1911.
-
Help for first time reloader - 9mm OAL Flat Point
found bry hbfp at 1.060 http://www.accuratepowder.com/wp-content/uploads/2011/01/accurate_load_data_3.5.pdf l: 4" ■ Twist: 1-10" ■ Primer: WIN WSP ■ Bullet Diameter .355" Plated bullets Solo 1000 115 BRY RNDS 3.4 935 4.4 1,057 34,113 1.130 Solo 1000 115 RAN RN 3.5 929 4.3 1,052 34,327 1.140 Solo 1000 124 BRY RN 3.4 850 3.9 964 33,684 1.160 Solo 1000 124 BRY HBFP 3.3 858 3.9 967 33,929 1.060 Solo 1000 124 RAN HP 3.6 881 4.2 993 34,818 1.110 Solo 1000 124 RAN RN 3.5 899 4.2 1,011 34,910 1.160 Solo 1000 147 RAN TRN 3.0 767 3.7 871 34,173 1.160 No 2 115 BRY RNDS 3.7 976 4.7 1,103 34,853 1.130 No 2 115 RAN RN 3.8 957 4.6 1,081 33,695 1.140 No 2 124 BRY RN 3.8 922 4.4 1,042 34,237 1.160 No 2 124 BRY HBFP 3.3 881 4.1 999 34,231 1.060 No 2 124 RAN HP 3.3 885 4.2 1,001 33,618 1.110 No 2 124 RAN RN 3.8 930 4.6 1,055 34,751 1.160 No 2 147 RAN TRN 3.2 796 3.8 901 34,683 1.160 No 5 115 BRY RNDS 5.7 1,023 6.5 1,145 33,667 1.130 No 5 115 RAN RN 4.8 1,017 5.9 1,150 33,854 1.140 No 5 124 BRY RN 5.6 977 6.3 1,104 34,132 1.160 No 5 124 BRY HBFP 5.0 948 5.8 1,069 34,456 1.060 No 5 124 RAN HP 5.3 961 6.1 1,085 34,392 1.110 No 5 124 RAN RN 5.6 986 6.4 1,118 34,451 1.160 No 5 147 RAN TRN 4.8 855 5.5 967 34,884 1.160 No 7 115 BRY RNDS 7.0 1,047 8.2 1,185 34,933 1.130 No 7 115 RAN RN 5.7 1,027 6.7 1,165 34,399 1.140 No 7 124 BRY RN 6.7 997 7.6 1,120 34,312 1.160 No 7 124 BRY HBFP 6.0 948 6.9 1,072 34,627 1.060 No 7 124 RAN HP 6.3 954 7.2 1,080 34,204 1.110 No 7 124 RAN RN 6.7 993 7.7 1,124 34,634 1.160 No 7 147 RAN TRN 5.7 867 6.6 984 34,748 1.160 Copper Bullets Nitro 100 NF 95 BAR TAC-XP 3.2 980 3.7 1,109 34,123 1.160 Solo 1000 95 BAR TAC-FBXP 3.9 1,021 4.6 1,156 34,210 1.160 No 2 95 BAR TAC-XP 3.9 1,023 4.7 1,158 34,754 1.160 No.2 115 BAR XPB 4.1 905 4.6 1,005 33,330 1.160 No 5 95 BAR TAC-XP 5.7 1,079 6.5 1,218 33,966 1.160 No.5 115 BAR XPB 5.0 959 5.5 1,065 33,880 1.160 No 7 95 BAR TAC-XP 7.0 1,093 8.0 1,242 34,913 1.160 Frangible Bullets No. 2 90 SF RHFP 4.3 1,080 4.8 1,200 34,620 1.120 No. 2 100 SF RHFP 4.0 978 4.4 1,087 34,270 1.120 No. 5 90 SF RHFP 5.6 1,101 6.2 1,223 33,540 1.120 No. 5 100 SF RHFP 5.2 1,031 5.8 1,145 34,600 1.120 Nitro 100 NF = New Formulation.
-
The new member of the family
Nice..Good luck with it..
- ACTION ALERT: Bergen County Residents
-
official gun, tactical light and laser pic thread
Elmer AKA " RAY RAY "
-
'Pirate Cave' In Humboldt Contained Gun Aresnal, Such a shame, those beautys gonna get melted down...
How many Mexicans does it take to deliver 117lbs of pot ?
-
My Neighbor just figured out he is on his own
The area i live in most everyone has a gun or hunts, those #s decrease every year as more people from up north move down.. One of their reasons for moving hear is the low crime rate.. Although the last 10 years petty crime seems to have increased.
-
Stolen handgun from Hillsborough home burglary found.
- RUGER 22/45 LITE BLACK AUCTION
SOMEONE ON THE FORUM WAS LOOKING FOR ONE OF THESE.. 3HRS 30 MIN LEFT. http://www.gunauction.com/buy/11747171/pistols-for-sale/ruger-22-45-lite-with-threaded-barrel-22-lr-new-in-box- 2/17/13 - Steel @ OBRPC
Bummer, i was looking fwd to trying out the 22/45 lite..- "Do you have your permit sir?" -1 for Sportmans Rendezvouz
Years ago when i would go to zueses, they use to ask for a fid or drivers license and hold it until you were done. I ended up working with a former employee of theirs and he said they would hold too keep someone from a grab and run..- Fun time at dicks
Old habits are hard to kick...- Finding a FFL when using Gunbroker.
Arms n Ammo is near your neck of the woods. http://njgunforums.com/forum/index.php?/forum/81-arms-n-ammo/- Boycott Sales of Ammo to Government Entities - Only Private Citizens
our PD years ago use to reload.. 38 spl's- Phone meeting with Assemblyman Charles Mainor.
Screw that go take a big dump while your on the phone with him, We all know your going to have to go once your on the phone with him..- Guncase foam
your welcome that site is awsome i put it in my favorites..- OK 1911 fans this has me interested.
That is sweet, looks like safety and grip safety and a few other parts are black chromed..- Kimber Covert II Pro Carry
found the topic when i replaced my stop. http://njgunforums.com/forum/index.php?/topic/31485-firing-pin-stop-replacement/page__hl__%2Bextractor+%2Bclocking__fromsearch__1- Kimber Covert II Pro Carry
The extractor may need to be tuned. The firing pin stop on my kimber was letting the extractor clock causing same issue you have. Extractor Tuning Tips By Bill Wilson A well fit extractor is essential to the reliability of any M-1911 pistol. The following guidelines apply to fitting a new extractor, or properly tuning the one you have in your gun. 1. Correct Tension With the slide taken off the frame and with the barrel removed, slip the rim of a LOADED cartridge under the extractor hook and position it so that the extractor is gripping the case at the center line, as shown in fig 1a and 1b. You should now be able to lightly shake the slide in any direction, without the cartridge falling off. If this test is unsuccessful, you will need to adjust the tension. For tension adjustment, place aprox. 1/2" of the tip of the extractor into the extractor channel and apply just enough pressure to slightly bend the extractor. Be careful, a little goes a long way! See figure 1c. Do not put more tension than needed to perform this simple test - too much tension will result in feeding malfunctions whereas too little tension can cause failure to extract and/or erratic ejection. 2. Positioning of the Extractor The locator pad (the radiused lug behind the extractor groove) determines at what point the bottom of the extractor groove contacts the rim of the cartridge and puts tension on it. Slide the rim of an EMPTY case under the extractor hook and position the case so that the extractor hook grips it at the center line. Now pull the case downwards approx. .075 - .1000"; there should still be tension, enough to keep the empty case in position even when the slide is lightly shaken. The same test performed with a loaded round should result in the cartridge falling off. This equals roughly to 1-1.5 lbs tension on the case. If you have correct tension on the case when it is centered on the breechface, as described in (1) above and little to no tension at all, with the case being pulled down approx. .075 - .100", you need to bring the extractor groove closer to the firing pin hole. This is done by removing a small amount of material at a time, from the locator pad, while maintaining the radius. Constantly check for correct tension, so that you don't take too much material off. See sketch below. 3. Fitting the Firing Pin Stop The fit of the Firing Pin Stop to the groove at the rear of the extractor is crucial to the correct extractor positioning. If there is a loose fit, then the extractor will move or twist, causing inconsistent ejection. With the extractor installed, the firing pin stop should slide into position using normal finger pressure. If the firing stop binds (when installing a new extractor), you will have to reducve the width of the firing pin stop, by removing material from its right side, where it contacts the extractor. Remove only a few thousandths of an inch at a time, while being careful to keep the right side parallel to the left side. When correctly installed, the firing pin stop will fit snugly into place, which prevents the extractor from twisting.- Guncase foam
http://www.foamonline.com/ add your demensions. http://www.foamonline.com/cube.php?cartID=e2bd22ce2347d6a2805e4501a84fc0d7- Grrrrr. Some dealers are a pain in the ass
A lot of kimber pistols were 6-8 months wait period before Obama's re election.. More kimbers are sold than any other 1911 Gunbroker is always your friend when looking for hard to find pistols.- “USA USA” Chant is Racist - i didn't know that
Apparently since our greatest president - RUGER 22/45 LITE BLACK AUCTION