Everything posted by Pizza Bob
-
Kimber Master Carry Pro...
You are right - there is no comparison, the P220 wins, hands down. Ask some real operators, who are going in harms way, whether they would rather carry a P220 or a Kimber 1911. As others have said - if you own a Kimber and have had no problems - good on you. But just because a gun is "pretty" doesn't mean I am going to overlook functionality. JMHO Adios, Pizza Bob
-
milt sparks holsters
Worth the wait. Worth the money. I have four of them and they are the most comfortable IWB holster I've ever used.
-
Muzzle Brake vs. Compensator
That's about the size of it. LOL
-
1st Cleaning in 20+ Years
White vinegar will help get rid of the lead deposits (which is normally what the build-up consists of in the compensator), but it can damage the finish. Vinegar is acetic acid and reacts with the lead. Do not let it soak in vinegar long term. If you try this, make sure that you flush everything the vinegar touched completely. Probably better off doing what you have been doing, but letting it soak a while. Adios, Pizza Bob
-
Muzzle Brake vs. Compensator
AFAIK, a brake and a comp are essentially the same thing. They are a device which redirects the gases of a fired round. An argument could be made that a brake directs the gases rearward, thus braking the recoil impulse, while a compensator directs the gases upward helping to mitigate muzzle rise. What you don't want is a flash hider. Brakes/comps are differentiated from hiders by virtue of the fact that the exit hole is very close to projectile diameter, while a hider has an open end. HTH. Welcome back. Adios, Pizza Bob
-
1st Cleaning in 20+ Years
If you are talking about the screw at 12 o'clock, that has nothing to do with the brake - that holds on the sight. Completely remove the two brake allen screws (3 & 9 o'clock) and then try again. There is probably a lot of crud accumulated and it may be difficult to remove, but my guess is that you just haven't backed out the allen screws far enough.
-
Somerset 5/19 / And PB Tries His Hand at Smithing
Better than I did. Ran flawlessly and the sights were right on, so couldn't ask for more. Only bobbled one reload badly - and it cost me a head shot because I was hurrying. Results aren't out yet - just hope I beat my son. LOL. Adios, Pizza Bob
-
Lets see your Dog aka 1st line of defense for some...
English Pointer?
-
James Bond Guns
As GRIZ said, his law is already on the books in NJ. And there is nothing pretentious in what he says or how he says it - only naivete in your response. Literally millions in our state tax dollars have gone into research to try and make this work - I believe that it was at the NJIT, or Stevens. but the results were unworkable to the point that the legislature defunded the project. If this is such a good idea, then why has LE opted out? 10X points out many of the potential failure points. This, in no way, helps our 2A cause and just attempts to place further restrictions on our rights. You really do need to think this through. Adios, Pizza Bob
-
has anyone had a Garand accurized?
No need to send it off, you have a primo Garand smith right in Ewing Twp (north of Trenton on Rt 31). Here's his contact info... http://www.radomski.us/njhp/major.htm He is a member of the board, but he only lurks and even that infrequently. Adios, Pizza Bob
-
Looks like CA is even dumber than NJ
This is just CA's way of instituting a defacto gun ban. They are dumb like a fox. Hopefully someone will challenge this in court.
-
Newest Hobby
You might get a kick out of this. This guy is a friend from high school. Started a business when we were in high school selling Hodaka motorcycles (remember them) and it grew into "Big Boys Toys, Inc." selling boats ATV's etc, etc. The rest of the story is here... Have fun. Adios, Pizza Bob
-
Somerset 5/19 / And PB Tries His Hand at Smithing
Bring it on!
-
Somerset 5/19 / And PB Tries His Hand at Smithing
Rosey, I really appreciate the offer, but I have full faith in that what I did will work. As I said, the trigger is more smooth than light. Light was comparatively speaking with the original - which was atrocious. If I were you, I'd bring it, and the rest of your gear, along anyway - there were open slots and even some of those spoken for may pull a no show. A little SSR conclave? Alec: Here you go... http://www.youtube.com/watch?v=bBhZ0SibaCU Adios, Pizza Bob
-
Somerset 5/19 / And PB Tries His Hand at Smithing
14# was the middle choice in the Wolff kit - it comes with 13#, 14# and 15#. I don't have a trigger pull gauge - not sure I really want to know. For me, it's more about "feel" and smoothness, than trying to obtain a specific weight of pull. This gun's trigger now feels very much like my 646. I picked-up the shoestring / torsion spring trick on You Tube. The shoestring is just used to keep the spring in place, once you manage to get the short leg in the hole and the body in the recess. An allen wrench is used to depress the long leg while inserting the hand. The allen wrench needs to be of a size that the opposite flats just fit within the walls of the trigger, thus not allowing the leg of the spring to slip past it. Same idea as your punch, but the flats have more bearing surface and provide a larger barrier to bypass. Probably could have done with two hands if my vice was easily accessible (buried with junk). I have more trepidation about using speedloaders than anything else - got spoiled with moonclips. Adios, Pizza Bob
-
Somerset 5/19 / And PB Tries His Hand at Smithing
I had planned to shoot this match with my S&W 625 - as has been the case for the last 6 to 8 months, however, Agent Smith has inspired me. He sought some advice on this board and then followed through and is about to embark on his first experience shooting a revolver at an IDPA match. He will be shooting a S&W 686 in which he has installed a lighter rebound and main spring. On April 30th I picked up my new (to me) S&W 586, chambered in .38 Special, with the intention of performing some light mods to make it more suitable for IDPA. Those mods, originally, were just going to be springs, as Agent Smith had done. When I got the gun (bought it sight unseen from a friend) I tried the trigger and it was among the worst DA trigger I have encountered on a Smith, so it sat in the safe these last two weeks. After reading about Agent Smith's intentions, I figured it wouldn't be right for him to "go it" alone tomorrow, so I grabbed the 586 and a bunch of necessary tools etc, and decided it was time to test my skills beyond replacing springs. I got in over my head, but I am glad to report that the gun is back together and there are no leftover parts. I did find that there are a bunch of small hidden springs, that our buddy, Larry Potterfield fails to mention. The most onerous of those, a small spring call the hand torsion spring in the trigger. This little bugger required three hands, a shoelace and an allen wrench to get back in place, so I had to wait for my GF to come home and lend the third hand. So I stoned the trigger and double action sear mating surfaces, installed a 14# rebound spring and a reduced power main spring and after struggling with the side plate for a bit, managed to button it up. Vast improvement - just a seat of the pants guess but probably reduced pull by three pounds and, more importantly, a smooth, uniform pull all the way through. I have never shot this gun. I have no idea where the sights are pointing. I haven't worked with speedloaders since some bowling pin matches of the early 70's and I have no idea if the lightened mainspring will ignite the ammo I intend to use (less worried about that than the other factors), but here I go, using it in tomorrow's match. Last time I shot an untested gun in competition, it did not end well (Steyr), but call me crazy, I have high hopes for this time out. So, Agent Smith, you will have company in SSR tomorrow - please don't humiliate me too badly. See you there. Adios, Pizza Bob
-
S&W Mod 10 New at Lawmans Supply
Yes - heavy barrel. The blued guns (model 10's) came with either a non-tapered heavy barrel or a thin very tapered "pencil barrel". When they switched to the same gun in stainless (model 64 - in 1970) they also came with a tapered barrel, but that was dropped in 1973 and the stainless guns only came with heavy barrels.
-
S&W Mod 10 New at Lawmans Supply
I thought you had seen them. I was only asking for the edification of the board. Not worth the drive to me - but if I were in the market for a model 10, I'd want it to be the HB variety.
-
S&W Mod 10 New at Lawmans Supply
Are these 10HB's or pencil barrels?
-
Open ranges near Mercer County?
Ready, Aim, Fire in Bristol, PA and Classic Pistol, in Feasterville/Southampton, PA. For outdoor, you have Wican's in Holland, PA
-
Speedloader pouches in IDPA
If carried on the weak side - yes. First holder can be on the CL, others behind that one. See you there - not quite ready to attempt SSR (working toward that), so will be shooting in ESR, as usual. Adios, Pizza Bob
-
Speedloader pouches in IDPA
Depends - there are two schools of thought. If you load weak hand, then the three speedloader/moonclip holders go on the same side as a magazine pouch would (your weak side). Doing a weak hand reload means that your strong hand never comes off the grip. A weak hand reload requires more practice because you are using fine motor skills with the non-dominant, less dexterous hand. A strong hand reload requires you to shift the gun to your weak hand while inserting the speedloader or moonclip with your more dexterous strong hand. If you use a strong hand reload, under IDPA rules, you may have two speedloaders/moonclip holders in front of your holster (concealment rules still apply) and one behind the holster (total 24 rounds: 3 loaders + the loaded gun). The ammo holders in front must be no more than an inch from the holster and each other. No restriction on the rear one. Make sure that your speedloader holders meet IDPA rules also. They must have either 360 degree coverage of the body of the speedloader, or have a flap to secure the loaders. The metal spring clip holders that are open on the top and sides are not legal for speedloaders. However, they are GTG for moonclips, providing they have a center post that protrudes through, and extends above, the center of the moonclip. Good article in the current IDPA Tactical Journal (Second quarter 2013 - Vol I / Issue 2) on the various revolver loading methods, by Massad Ayoob. Adios, Pizza Bob
-
Need recommendation for larger grips for S&W 686
They may not be that much larger in girth, but what they do is increase the LOP - blackstrap to trigger face. They are about $37 + SHI and are available in orange, yellow or black. Adios, Pizza Bob
-
Need recommendation for larger grips for S&W 686
Is your 686 a round butt? If so, Hogue makes grips that cover the blackstrap. They are used on the X-frame guns and only available on S&W's website. Adios, Pizza Bob
-
S&w 686+ 3"
Well you still have tomorrow to think about it, as they aren't open on Mondays. What caliber was your score? Just guessing.