Everything posted by Pizza Bob
-
Saturday's visit to Shore Shot
I close both my eyes. Isn't that the way you're supposed to do it?
-
Possible Issue w/USA Ammo New 9mm 115g Lot#16081130
Glenn, you are :thsmiley_deadhorse: . Measuring the ogive isn't real relevant in this case. Just looking for undersized bullets that would allow some yaw in the freebore, before hitting the rifling, that would result in a destabilized bullet when it exits the barrel. If these were truly measuring .334" or .335" at the major diameter, then I would have to think that's the cause of the keyholing. I'm also wondering if Krdshrk isn't onto something. They may very well be swamped with e-mails since entering into their controversial e-mail ad campaign. Chances are the OP's e-mail got burried in the torrent. They were very responsive to the KB issues with the AR's. Adios, Pizza Bob
-
.22 Magnum Try-out request
Griz: You make some valid points, however, the new .22 mag SD ammo from both Speer and Hornady is formulated for short barrels and uses low-flash powder. I believe they have identified a viable niche market. Not to be sexist, but many woman find even medium frame size handguns to be too heavy, which means that they gravitate to things like airweight J-frames, without realizing the unintended consequence of increased recoil and muzzleblast, until they shoot it for the first (and in a lot of cases last) time. I think that you'll agree that any gun is better than no gun at all. Now that we have manufacturers crafting low-flash SD ammo in a round that has negligible recoil, the light weight J-frame comes into its own, as a SD gun that just about anyone can handle. Given the OP's special circumstances, this combination meets their needs. I wholeheartedly agree about the NAA mini's. They make a neat belt buckle - SD gun? Ummmmm....not so much. Adios, Pizza Bob
-
USPSA @ CJRPC 12/11
Who's in? There was mention at November's match that with the decreasing daylight hours and the increasing popularity, a pre-registration plan may be implemented with a cap on number of entrants. Anybody heard anything more - or am I confused, as usual? At any rate, I plan to be there. Adios, Pizza Bob
-
What's the difference...?
232's are also heel mag catches. Sig Exeter was pushing to have the 232 made here and they would have switched to an American mag release. That didn't happen and now there is the 238 for those that absolutely must have the mag release under their thumb. Adios, Pizza Bob
-
Vizsla pup
He will most likely see your post and respond, but if perchance he doesn't, try PM'ing Lunker. His Vizsla is under a year old, I believe. Adios, Pizza Bob
-
Centralia PA
Vlad may be responsible for singlehandedly turning the Centralia boondoggle into PA's leading tourist attraction. Folks, believe me, when Vlad said that his pictures pretty much show everything there is to see, of any interest in Centralia, he was right. Was probably actually overstating the case. If you are traveling in that direction, it is a nice distraction. Get off the highway and take some nice secondary roads. But to travel 2 plus hours to see what remains of Centralia will be highly disappointing, I assure you. It is only about an hour travel time (appx 37 miles) north of Cabela's, so if you really must see it, maybe you can make it a "twofer" and hit both places. Drive safely. Adios, Pizza Bob
-
Is this Legal in PRNJ
Was there ever any resolution as to whether the way this bullpup is configured, that the grip is actually a "pistol grip". I thought the connector strap at the bottom was an effort to circumvent the "pistol grip" laws by making it a thumbhole (albeit a large thumb) stock? Just wondering. Adios, Pizza Bob
-
New state paper work requirements as of Sept. 2011 ?
Big Blue: I don't know where your department came-up with this "new" requirement BS, these elements have been required since I first got my FPID in 1979. They obviously have not been following the law. Also the consent to search mental health records is a single page. Required under the statute are: STS-033 - Application for FPID or Permit to Purchase - $5 for FPID and/or $2 for each P2P SBI212A - Non-criminal background check (in leiu of fingerprints, providing you had been fingerprinted previously) this is the $18 charge SP-066 Consent to Search Mental Health Records - N/C but must be signed in the presence of a LEO These are the only three forms required by statute. The deal with your references is actually they are requiring you to do their job for them. The forms themselves would most likely be OK, if the PD sent them to your references. Then they are covered under performing an investigation. My township does the same thing and I went a couple rounds with the Twp Solicitor and he thinks it would stand-up in court - not something I'm in a position to challenge. I get the feeling that there are many PD's out there that have never read, let alone follow the NJSP Guide - SOP or not, which is one reason the NJ2AS case was so important. I hope they take it to the next level and appeal. Adios, Pizza Bob
-
OMG – What Have I Done?!?!?
I have a natural tendency to grip the gun low on the grip. If I put my strong-hand thumb in that indentation, it forces my grip higher so that the web of my hand is where it's supposed to be. Still waiting (been almost a year since they "announced" it) for my Sig 1911 Target Elite in 9mm. I have six Wilson mags already here, and a set of wild G-10 grips for it on order. That'll never happen No holster, no mag pouches and not enough mags. We'll start to remedy that on Monday. Adios, Pizza Bob
-
44 magnum shooters?
Today was a great example of, "You're never too old to learn." There was a fellow shooting a revolver today at Shongum (quite proficiently, I might add). It was a model 625. He had orange rubber Hogue grips, that covered the backstrap, on it. Now, I knew that S&W had used grips like that on their "Emergency Pack" guns that were built on the X-frame. But, to my knowledge, Hogue never made anything like that for the N-frame guns. So I asked him where he found them and he told me that they were indeed the grips from the X-frame guns. Seems that if the N-frame is a round butt, the X-frame (which also fit K/L-frames) Hogue grips will fit it fine. Square butt guns are a no go however. In your photo, the two guns on the left are round butts, the three on the right (which includes your 629) are square butts. The only rubber grips that I know of that will cover the backstrap of an N-frame square butt are Pachmayr's. Both their Signature grips (which used to come in two sizes - don't know if that is still the case), and their gripper grips, which are finger groove type. You may want to check out Trausch grips - I really don't know anything about them, but they may be another alternative. I currently have wooden Hogues (with an exposed backstrap) on my 29-2, and it is punishing to shoot. At least with synthetic grips you don't have a pile of dough wrapped up in them. Adios, Pizza Bob
-
44 magnum shooters?
Incorrect. The X-Frame (.460/.500) uses the K/L grip frame. Your 629 is an N-Frame. Sounds like your 686 is a round butt while your 629 is a square butt. I have some .44 magnum loads that will make you sit-up and take notice. If you dampen the powder a little bit, you can then tamp it down better and get a smidge more in the case Adios, Pizza Bob NOTE: For you new reloaders, the above was a joke......just thought I better add this disclaimer before the hate mail starts rolling in.
-
OMG – What Have I Done?!?!?
I thank you for your restraint. Looks like something that should be on Batman's utility belt, doesn't it?
-
OMG – What Have I Done?!?!?
OK, here are some pics... Off to Shongum. Adios, Pizza Bob
-
Possible Issue w/USA Ammo New 9mm 115g Lot#16081130
I'm confused. How are you measuring bullet diameter at the ogive? The ogive is a constantly diminishing diameter. The bullet should have been pulled and measured at the base or close to it - the part that goes into the neck of the case. I hope we're just dealing with semantics here. If the major diameter is only .334" then yes, I'd say that's the problem. Please clarify. Adios, Pizza Bob
-
OMG – What Have I Done?!?!?
I have expressed my disdain for tactical Tupperware a number of times on this board. The only plastic pistol that has wormed its way into my meager collection is my Ruger LCP, and that was a function of size, not material. I was witness to one of the first Glocks in the country, back in the mid-80’s, when a gun writer of my acquaintance brought one to our club practice night for some T&E. It was pretty much pooh-poohed by all as having no possibility of catching on – of course this was at a time when real men shot 1911’s and even those strange D/A S&W model 39’s and 59’s were looked upon with a jaundiced eye. Plastic is for toys, metal is for guns. Well, not only have I just become the owner of a polymer-framed handgun (have to be PC now that I have joined the cult), but I did it by violating every tenet that we preach to every newbie that comes on this board and asks, “What gun should I buy?” Which is usually followed by a slew of posts telling them to try before they buy – not just hold the gun, but actually shoot it before they plunk down their hard earned dollars. Not bad advice, but this is a case of, “Don’t do as I do, do as I say.” People that know me, personally, and from the board, know that I have a penchant for the quirky, oddball and out-of-the-ordinary ordnance. Witness things like my most recent CZ Royal, or the flat-top Bisley in .44 Special. I just don’t want to see myself coming and going, so I take pains in discovering these “oddities” (apologies to Fishpaw – not that odd). So, “What did I buy?”, you may ask. Well, I’ve already let the cat out of the bag, in that it’s made of polymer. It’s chambered in the mundane 9mm (that was an economic and competitive decision) and it was built in Austria. (Old School is salivating now, thinking he has another convert to his coven). Well, it’s not a Glock – I continue to dislike the Glock on grounds of aesthetics, ergonomics and commonality. But it is what many people say the Glock should have evolved to, or been in the first place. In fact one of the people that had a hand in the design of the Glock, designed this pistol, in its entirety. Sight unseen (except for photos), so obviously untouched / never handled, I laid down the cash for the latest generation of the Steyr M9-A1. Stylistically it is a little out of the ordinary – you can see that there are elements used on XD’s and MP’s and the trigger system is similar to the Glock (although this generation has improved it), but there is no mistaking this for anything but a Steyr. Every gunwriter that has reviewed this (and admittedly, there weren’t many) has commented on the great ergonomics. Likewise the trigger and the lack of muzzle flip, due to its extremely low bore axis relative to the hand. The other neat features include frame rails that are replaceable – not molded into the polymer, and Steyr’s unique trapezoidal sights consisting of two triangles – a solid, colored one for the front and an open, topless one, bracketed by two bars, for the rear. For those that are thinking of following in my footsteps (it could happen), here is a caveat: For some reason Steyr chose not to change the model designation when they upgraded to this latest generation. The few changes that were made enhanced function. They are the aforementioned trigger upgrade (smoother, shorter, lighter with a shorter reset) and the elimination of the loaded chamber indicator (LCI), which was a pin that protruded from the rear of the slide when a round was chambered. It was suspected that this affected an occasional FTE. There is still a hole in the barrel hood to check chamber status. The trigger upgrade is visible and the best means to insure you are getting the latest, most current generation. It consists of a cross-pin, through the slide just below and to the rear of the rear sight dovetail – none of the previous M, S. or C series Steyrs had this pin. (M = Full size / S = Compact / C = Full size grip frame with Compact slide & barrel). I mention this because there are a ton of Steyr M’s on the market right now that were part of a military contract overrun. They consist of slides manufactured in 2004 mounted on later frames – they have the LCI and do not have the cross-pin. These were imported by PW Arms of WA state – and are so-marked - (not Steyr USA, so who knows what the warranty status would be?) and are being sold at firesale prices by several big Internet vendors. I didn’t want old problems, so I opted to spend the extra money and get the current generation imported by the parent company. Magazines are metal and appear to be Mec-gar. They make 10, 15 and 17 round mags. Since there aren’t many Steyr dealers, my gun is coming from a distributor so I had to get it with two 10-rd mags. That’s OK because the 15-rd mags are readily available and since both IDPA / SSP and USPSA / Production limit you to 10 rounds anyway, they’ll see significant use. I’ll pick-up some additional 15 rounders. Paul (PK90) was a huge help in this endeavor, putting-up with all my anal BS regarding making sure this was the current generation and even suffering a pitch from me for him to become a Steyr direct dealer. He was of immense help. I just got back from picking it up. I won’t be able to post pictures until Sunday. Adios, Pizza Bob
-
.22 Magnum Try-out request
This... http://www.smith-wesson.com/webapp/wcs/stores/servlet/Product4_750001_750051_764925_-1_757768_757767_757751_ProductDisplayErrorView_Y Loaded with these... http://www.speer-ammo.com/products/954.htm
-
GSG 1911
Harry: There is no DP sight set for the GSG/Sig 1911-22. They only have the front. I have heard of some people installing a Novak cut rear sight, but it did entail some modification as the GSG rear dovetail is proprietary. Adios, PIzza Bob
-
Possible Issue w/USA Ammo New 9mm 115g Lot#16081130
Ahem....it was my post. I'm not sure when that ad was sent, but I got the impression that the ammo inquiry pre-dated the release of the ad - but I'm not on their mailing list.
-
.22 Magnum Try-out request
You firing just any .22 mag revolver isn't going to tell you much. As far as SD/HD revovers chambered in that caliber, the lightweight S&W J-frame fills the bill. Gives you seven rounds - as opposed to five rounds in the same gun in .38. You should first find someone close-by with a J-frame and see if your mother can manipulate the cylinder release and is capable of pulling the trigger in DA or SA mode (preferrably both). I think recoil will be negligible to the point it will be a non-factor - even for someone with arthritic hands with a lightweight revolver. Both Speer (Gold Dot) and Hornady (Critical Defense) now make viable SD/HD rounds in this caliber. While I am certainly a proponent of "bigger is better", any gun is preferrable to no gun. When there are physical limitations that have to be adapted to, I think the .22 mag can be a great solution. Adios, Pizza Bob
-
Possible Issue w/USA Ammo New 9mm 115g Lot#16081130
Pull multiple bullets. Weigh them and measure them (diameter). Then section them and determine if they are jacketed (copper cup drawn around a lead core) or plated - should be obvious by the thickness of the covering. If jacketed, check for uniformity of jacket thickness and gaps between core and jacket. If cast and plated, look for casting voids in the lead. This is a good beginning - if this reveals nothing, maybe USAammo will replace your batch and test the ones you send back. Perhaps what is more troubling is their (USAammo's) lack of response. As I recall, they were very responsive to the AR KB and not only made good on the rifle, but came clean on what the cause was. Despite their name, I believe that, at least some, of their components used in the manufacturing process are sourced from other than the USA. I believe the powder that caused the AR KB was one such component. Good luck. Adios, Pizza Bob
-
Centralia PA
Passed through Centralia many times, and while it is an extreme example (maybe the tunnels are closer to the surface), it is not unusual in deep mining country. Giant's Despair south of Wilkes Barre has also been on fire for over 40 years. Apparently it isn't dangerous to the level Centralia is, as no effort at relocation has ever taken place. They did however, make an attempt to extinguish the fire. There was access to one of the tunnels right in front of the barbershop I used to go to. They constructed a large hopper with a ramp to its brim. The hopper was plumbed into the water system (via a fire hydrant IIRC) and all day, everyday, for months 17 ft dump trucks (thats appx 30 tons) would back up the ramp and dump their load of earth into the hopper, where it was mixed with water to form a slurry and was pumped down into the tunnel. This went on for months. I don't know whether they gave up in frustration, or ran out of funds, but the fire is still burning today. On cold days you can see plumes of steam coming out of naturally occurring vents on the hillside. Giants Despair is also where one of the oldest continuously run (automotive) hill climbs is held. Not sure if he still does, but Oscar Kovalesky and his Polish Racing Team used to hold the hill record in an old can-am car. Adios, Pizza Bob
-
USAammo In The News
Say what you like about their ammo (and I'm not a fan), but they do have cajones... http://washington.cbslocal.com/2011/12/01/new-gun-company-advertisement-compares-obama-to-hitler-stalin/ Adios, Pizza Bob
-
Carbine/Pistol Tactical Class ... Here in NJ!!
I'd make sure that they are aware of the restrictions here in the PRNJ: No mags >15 No folding collapsible stocks No bayonet lugs The above assumes the use of AR's or equivalent. This will be like going to another foreign country for them. Sorry to pi$$ in your cornflakes. Adios, Pizza Bob
-
Youngest off to Boot Camp
Jimmy, Congrats to your youngest and thanks to all of you for your service. There is another board member who'll be heading to Great Lakes, but he had the good sense to wait until spring. I don't want to steal his thunder, or be a distraction to this thread, so we'll let him pipe-up if he wants. While you'll surely miss him, I'm bettin' that you two will enjoy being empty nesters. Adios, Pizza Bob