Everything posted by T Bill
-
you folks ready? hurricane season...
Systems based on fossil fuels (diesel, gas, nat gas, propane) require some to deliver them to your area. In a major disaster such as Sandy you have to have plans to get you to your next step. When NY state was hit with that severe ice storm several years ago, it did not make any difference, all short terms plans were not enough. People still had to leave their homes. Major distribution towers for electric were lost, road blocked for weeks, freezing cold weather. Best it allowed you to do was make an orderly exit from your property to somewhere else leaving with only what you could carry in your car, if you could use the car get out.
-
If she was drawn on or shot... how would you feel?
Until I see sparks flying from her finger tips, nice acting. Remember believe half of what you see and none of what you hear.
-
you folks ready? hurricane season...
Pull the main and go from there. Test before you need it. Stabilize the fuel. I use Startron and high test. Never a problem. Keep fuel bowl empty till you need to use it.
-
What's the scoop on the G21SF?
There is a picture reference on another board,(cannot find it right now) comparing a G21SF to a G21G4. Basically they are equal. No real reason to consider the G21SF. Without the back straps a G21G4 is a G21SF with better grip pattern, three mags, larger mag release that can be reversed, and a better slide spring. I will look for the reference. This is the reason went with G4 and not SF.
-
Electronic NICS
When will this state learn we are the customers. Every interaction with this state is like they are doing you a favor. Nothing is done in this state for the benefit or ease of the taxpayer. Northeast states suck. Cannot wait to get the hell out of here.
- Hornady PTX
-
Hornady PTX
Hornady has a different PTX for each caliber. Users on other boards claim difficulty in adjusting. This reference may help. http://forums.1911forum.com/showthread.php?t=308430 This site also has aftermarket items that maybe of interest. http://inlinefabrication.com/collections/hornady-lock-n-load-ap-ergo-roller-lever I use an aftermarket expander I ordered from http://www.powderfunnels.com/. Again, a little difficult to setup, but once done works better than Hornady as it for all calibers. Not sure what you mean by quick change part.
-
AB Arms handguard, any good?
Have one w/o a top rail on a Colt 6400 right now. Tried this instead of the Magpul. I like the recess for the leading hand. Comfortable. Was part of a re-do to make the Colt lighter, with a Rogers stock. Front swivel was not a problem as Colt uses the left side mount on the sight tower. http://www.floridamilitarysupply.com/Colt-M-4-Front-Side-Sling-Tactical-Swivel.html
-
Day hiking trip in NJ or PA
This................ Live 10 minutes from here. Let me know when your coming up....... There is a nice loop trail for this from the Mohican Outdoor Center. Much less crowded this time of year than from Rt80 Dunfield Creek area.
-
Mako spare mag stock
Have it on my 300 Blackout. I like it. http://njgunforums.com/forum/index.php/topic/10555-ar-pics-lets-seeum/page-47 Post 1401
-
do they make....
http://www.gun-parts.com/remingtonshotgun/ Give Bob's a call, hopefully they would know. Remington does offer a 20 ga. youth 1187 with a synthetic stock #83626.
-
Huge -1 to Cherry Ridge
Just one of the many reasons I do not have a membership there. Used to, once was enough for me also. FYI, EFGA suffers from the same HIA syndrome. Getting better, but still suffers from it.
-
Home Carry
When my two oldest were very young , they were playing in the front yard, within 30 feet of the front door, two hunters chasing a deer across property lines shot right over their heads. Have had others just "walk through" carrying firearms during deer season. Property is even extensively marked, didn't stop them one bit. So the owner takes care of the problem now. Dial 911 second, secure scene first. PD is over 10 minutes away on a good day and state PD (covers overnight) is even longer.
-
Such a deal! Not!
Add this to the list............ http://www.patriotfirearmsandmunitions.com/
-
I appeal to you, my brothers, for a rocking Chili Recipe
Might work, just don't want to burn to bottom turns bitter then. I understand Serve Safe and Food Prep and to keep greater than 140 or below 40, but to let it stay on six hours? Can you make it, refrigerate it and reheat in AM? If it cooks to long the beans will break down to mush. Hell give it a try, bring it to a boil reduce heat right away to low, low simmer, just cover it to keep moisture in, then uncover it to allow excess moisture to escape and hope for the best.
-
I appeal to you, my brothers, for a rocking Chili Recipe
OK, one I developed for the Scouts to be done in a cast iron Dutch Oven but works in regular pot as well. It has won first place at the Scout Master Invitational at USMA, West Point. 1 1/2 lbs. ground meat, your choice, browned. Season meat while cooking as you see fit. Nothing crazy, just add a flavor, your choice. When browned, add to that 3-4 cans petite dice tomatotes (drained)the 13-15 oz size. You know what I mean. Factory Seasoned if you like. Add to that 1 or 2 1 lb jars of salsa, again you choose the heat level thick and chunky or whatever, or mix it up. Add 3-4 1 lb can of red kidney beans (drained) or your choice again. Mix thoroughly in the pot and bring to a boil. Lower heat to simmer, just enough to see a few bubbles, you know what I mean. Simmer uncovered to allow excess moisture to escape and the diced tomatoes to break down. About 2-3 hours. Serve with Corn bread muffins or those biscuits that come in the tube. At Boy Scouts they would cook this over an open fire in a Dutch Oven when it got close to done they would put the biscuit dough on top of the chili, cover with lid and put coals on top of lid. Ready to serve when the biscuits were done. Hope this helps. Good Luck.
-
Laminate flooring question
Start square to the room on a long wall by measuring all the way across the floor to the far wall. Strike a start line just off that wall that the molding will cover. Anchor the first course so it does not move. Begin each row staggering the joints so they do not run together. There is nothing saying the framework for the bathroom is square to the room. It probably in not. When a new course will not fill because it touches the bathroom wall then it will have to be notched to fit. There is a way to do this and describing here will not help, Google is your friend here. When you get to the far side of the bathroom carefully measure from the last row before cutting on the other side and strike a line on the floor. This is your mark to make sure your still square to the room and the notched boards on the far side of the bathroom are done correctly. The gap between the flooring and the bathroom saddle will need to be caulked with a near same color. Continue till you reach the far side and notch to fit again. Molding around the room should cover the gap between the wall and the flooring and around the walls of the bathroom. You need that space so the floor can "float". It will expand and contract and this is the reason for the gap. Two things either the flooring has it's own padding or you lay down roll padding first. Helps to keep the floor level. Level is important and the flooring will buckle it the subfloor is not within 1/8" over one running foot. Second, because it is a kitchen floor see what the manufacturer recommends about seam sealing the joints as you go. Wet will work its way into the joints, cause its a kitchen poop happens, and distort the edge as well as let moisture through to compromise the laminate. Good luck on the project. Hope this helps.
-
Suggest a buffer tube kit...
I have put a small bevel in the tube edge at the right place that allows that one extra turn you desire for the buffer retainer. Works OK, in fact the contour matches the profile of the retainer and seats better on the tube.
-
Home Carry
Is it legal? Yes? Doing it depends on your neighbors and the local gendarmes.
-
Such a deal! Not!
They've been on the "Do Not Disturb" list along with CTD for a long time now.
-
Home Carry
Carry Condition 3 all the time outdoors, sometimes to Condition 1, if I feel the need arises. Rifle and Shotgun always within a few steps. Live in the woods and critters always abound. Mostly 4 legged, sometimes 2, especially during deer season. I'm not Turtle Man and my neighbors know it.
-
Suggest a buffer tube kit...
Price is related to tube construction (6061 aluminum vs 7075 aluminum) and commercial or milspec, and whether material is stamped or machined. http://dsgarms.com/ProductInfo/MAG480-BLK.aspx http://dsgarms.com/ProductInfo/DSGMILSPECKIT.aspx Buffer tube is made from 6061 and milspec, 7075 is tops however. Plan on 7075 if you intend to participate in carbine training or other intense use of the firearm.
-
Think I found my next car...
My '68 Tang fastback never looked that good. God, I miss that car.................
-
Anyone shoot NRA Conventional Pistol (Bullseye) that can give me info?
Smith 41s, Clarks, and Ruger MKii targets (esp gov model 6 7/8) rule at BE. Do not know any BE shooters using upper end conversions. Just not that accurate for BE. BE shooters are shooting for score. Given your price range the Ruger will be about the best you can get. Even used 41s and Clarks have high resale value.
-
.22lr 2100rds Cabelas BACK IN STOCK
Remember, you can never have too much water in the reactor.