Everything posted by Vlad G
-
What can you tell me about my shotgun?
The purpose of the choke on any shotgun is to restrict slightly the diameter of the bore right before the shot leaves the barrel. This allows you to control the pattern of the shot downrange, basically how much the cloud of lead spreads as it moves downrange. Normally a shotgun with no choke is referred to as "cylinder choke" and then they narrow slowly through about 10 sizes (the more common ones being skeet, improved, modified, full). On most shotguns a portion of the last couple of of inches of the barrel is threaded and recessed to allow you to screw in whatever choke you want to use so you can switch around based on the need. There also a few designs for adjustable chokes (like the the polychoke) and your gun has one of those permenently attached, by twisting the bit at the end of the barrel you can change the choke and hence the pattern. It is probably safe as a range and field gun, and it won't dislocate your shoulder, although without proper technique it might bruise it.
-
What can you tell me about my shotgun?
The bolt action shotguns were made to be fairly inexpensive hunting guns. The 195k-a like your have an integrated adjustable choke, and odds are right now it is more useful as a conversation piece and for its sentimental value. As a hunting gun it might be ok of deer with buckshot but I wouldn't use slugs through it because of the integral choke might get damaged and I don't think they would be rated for the steel shot now required for waterfowl, although it might be ok with the bismuth type shot. I don't think they have much resale value.
-
Took the new AR for a test drive today, a couple issues...
You can't really rule anything out until you figure out what is actually wrong, it just smart debugging, but that said I can't think of a situation where the ammo would be the issue. If you had severely underpowered ammo or a gas flow problem and the gun short stroked or didn't feed the next round I would consider it, but I can't think of a set of circumstances under which the gun has bolt has enough rear movement to eject the spent case a feed a new one and NOT reset the trigger. If the trigger bits don't move, the hammer doesn't all, the firing pin doesn't hit the ammo so the quality of the ammo is not even relevant. My GUESS is that there is something wrong with your trigger group or there is something else going on you haven't told us about yet. Like maybe your thumb is moving the safety around a bit? EDIT: actually I CAN think of an ammo problem, namely if you are blowing out primers and they primers have made their way into your lower. Visually inspect your trigger group and make sure there are no primers stuck in there, there shouldn't be any brass bits in there.
-
Took the new AR for a test drive today, a couple issues...
1) make sure you left the trigger reset. The AR trigger likes to move back forward for some distance before being ready to fire. 2) if you let go FULLY of the trigger and you press it again and it does not move, the odds are one of three things have happened: a) The hammer did not engage the sear and moved forward with the bolt b) Your disconnector might be confused c) your safety is getting moved around. All of those conditions indicate a possible problem with the trigger group, have someone who knows what they are doing look at it.
-
Took the new AR for a test drive today, a couple issues...
1) What do you men that gun wouldn't fire? Would the trigger move? Did the hammer drop inside the gun? Did the trigger reset after the previous shot? 2) Hell no, the charging handle shouldn't lock back or it would hit you in the face. The charging handle ONLY moves when you manipulate it, all the rest of the time it sits happily inside the upper receiver or all AR shooters would be missing teeth. The bolt locks back, a new magazine in inserted and the bolt release button pressed.
-
CJRPC USPSA Easter Sunday???
I emailed the guy in charge of calendar about it.
-
CJRPC USPSA Easter Sunday???
It would be news to me if my own event would be canceled.
- HELP ME!!!!!!!!
-
M44 Mosin Hair Trigger Issue
The first step with any milsurplus gun should be stripping it down to its smallest parts, removing all the gunk, and checking the parts for wear and damage. This includes the trigger components, because until you take them all out and inspect them you don't know if someone took a file to them, if they are worn out, or if there is a bit of dirt or a rock or a primer or whatever stuck on the components making them misbehave. I went through a phase were I spent lots of time fiddling with milsurplus rifles (Mausers in particular).
-
why no picture or video allowed in bullet hole?
Assume for a second that you take a video of yourself doing something illegal and then post it on facetube (to steal a phrase from top gear). Now they look like they allow and encourage illegal activities. In general I think people are way to free with cameras while they do things that MIGHT be considered illegal, stupid, or ill advised, and people around guns are not immune to this.
-
Old Bridge USPSA 3-25-12
Don't worry about Ray, he'll be scratching at your door with the rest of the zombies when he runs out of ammo, while we calmly reload more As for the type of ammo problem you had, normally that happens when you rush the bullet sitting and the bullet snags the edge of the case an rolls part of it. I found that adjusting your expander to open up the case a bit more make this problem very unlikely.
-
cz 452 american l/h
Well they catalog them, might be worth ringing them up and see if they actually make it.
-
cz 452 american l/h
Out of curioisity, which Savage did you not like the fit on? I have a Mk II BTV which is excellently built and the make a lefty stainless version, the BTVLSS
-
Old Bridge USPSA 3-25-12
Yeah those poppers screwed with me because I was shooting over them and my brain refused to adapt. Shot 3 shots over them in the first array, corrected, then shot 3 shots over the second array cause I can remember things like that 10 seconds apparently. Bad brain, bad!
-
Old Bridge USPSA 3-25-12
I managed to pick up 3 mikes, all stupid. Not that all mikes aren't stupid, but these were just pointless. I guess I really should have zero'ed my gun after I replaced the front sight, but I only did that 2 days ago, eyeballed it and said screw it, it looks close enough. Surprisingly it really was, except for now it shoots kinda high at longer ranges and I've been shooting over things.
-
2010 total guns sold us and exported by co.
Ruger also makes frames for other people, I'm curious how they count those,
-
Old Bridge USPSA 3-25-12
I hope you guys are showing up. Weather is now clear, the chance of rain is down to 40% (which is code for "we don't think its gonna rain but we are covering our a**"), temps in the 60s
-
Will the boom in gun sales benefit 2A rights?
How about you show me EXACTLY what Obama changed where it says what you say it does. Quotes please. I bothered to read the thing, and the differences, and me and everyone outside some of the places like infowars seems to be reading it the same way I do. I'm no fan of Obama, but I don't see where you see what you see.
-
Will the boom in gun sales benefit 2A rights?
No it doesn't say that, plus that order has been around for quite some time, a bunch of presidents have renewed it, Bush included.
-
Never Waiste A Good Crises.......BHO.
Nothing I heard so far makes me think he will be absolved under state law. From everything I've heard so far the guy was an idiot and should go to jail for murder and probably will.
-
Will the boom in gun sales benefit 2A rights?
In view of Heller that will fail the first court test and every one after that.
-
Alternatives to Ear Muffs
I've been using 3M E-A-R 33nr foam plugs for some time now. If you order them from industrial supply places you end up paying like $30 for a 200 count box.
-
Fixed stock vs. pinned adjustable stock
Don't forget the rifle length recoil system used by the A1/A2 stocks is also smoother, softer, less noisy, and much more securely attached. The pinned collapsible stocks actually have a serious shortcoming as far as I'm concerned which is strength, you don't want to smack anything with them. I don't mean people btw, I mean if you ever have to mortar a stuck case out of the chamber you simply can't do it with a stock pinned in anything but the shortest setting without risking breaking it. I've had to do that at a match once (I had a case with no flash hole, primer moved back when it fired and locked up the bolt) and I smacked the crap out of the Ace stock, with a pinned plastic stock that would have been a no-go.
-
2012 Mid-Atlantic "Factory Gun" Championship July 6th-8th
Central Jersey Rifle and Pistol Club is proud to host the 2012 USPSA Mid-Atlantic section match. The match will be held on Saturday July 7th and Sunday July 8th 2012, with two shooting sessions on Saturday (AM and PM) and one shooting session on Sunday. We are planning on 8 stages plus a chrono stage. There will also be a shooting sessions on Friday for the ROs. Please note that this match will be a "factory gun" match with only the Production, Single Stack, Limited 10, and Revolver divisions being recognized, we are not offering Open and Limited due to state laws. This will be a prize match, in the order of finish in the division and class. We will be updating our webpage with more details as we approach the match date. If you have any questions, please contact us at [email protected] If you would like to volunteer to RO, please contact us at [email protected]. To sign up for the match please download the application and mail it with your check, following the instructions included in the application. Note that this is a fill in form type of application and we would appreciate if you type in your information before printing it and mailing it out, it will help us read it the pertinent details without having to call you for clarification. Sign up deadline is June 1 2012, which is also the refund deadline. Please note that you HAVE TO BE A USPSA member to shoot the section match.
-
Fixed stock vs. pinned adjustable stock
It looks cool? Maybe you can have it pinned at a convenient length if you have short arms? I'm a proponent of full length A1/A2 stocks, they shoot software, balance better and unless you need to be in vehicles a lot are just all around better. Unless you are short, in which case try the A1 length first anyway, then look at a pinned collapsible.