Rob0115

I shot 25 rounds through it yesterday to sight the scope and break it in a bit. It was incredibly smooth for a fairly light 308. Accuracy was tremendous. I shot it free standing 1x power at 50 and the groups were great.

No and it should fit no problem.

I have a cabinet that I can send a photo. Free for whoever wants it. Must come and pick it up. I couldn't post nj market place but I wanted a forum member to get this before sticking it in CL for free.

I did my 300 blackout in all Seekins billet stuff, upper, lower, rail and it was super light. I'd have to weigh but it was noticeably light. Couple that with a 14.5-7 barrel with a comp and you should have something pretty light.

It all looked fine in the description until this line: Ultra Fast Attenuation of muzzle blast gasses means that Flash Signature is also reduced Does that make it a flash hider? Blasted NJ and the intentionally ambiguous laws. Full description below. I was thinking about one on my FDE Tavor. http://www.atomictactical.com/lantac-dragon-5-56mm-compensator/

Is that a piston rifle? What does it cost?

It's complete. range report and photos to follow.

I'm thinking of switching from ATT. I bought a phone of craigslist to try it out and the coverage has been fine and so have the data speeds. I have 5 smartphones including my wife and kids and the bill would be reduced by more than 130 bucks a month. T-mobile is also willing to pay for your early terminations fees. My week with t-mobile seems to have been fine but I'd like to hear from others. Cheers

It's tough.

Joe bob just dun saved me 10 bucks. But this thread cost me 104. Ugh.

I just started using one shot for all my cases except 5.7 due to the lacquer requiring something heavier to protect. Did 200 rounds of .308 cases with no issues sat all. I just ordered up more, much better than rolling on an inking pad.

Using a LEE FCD place the bullet in the shell holder and raise the ram to the top. Run the crimp die down until it contacts the brass. Lower the ram. Some folks says a quarter, some say a half (too much IMHO) but turn it down about an 1/8 of a turn and raise the ram and see if you can feel a bit of pressure. If you don't feel much at all do another 1/8 for a 1/4 total. You shouldn't have to do any more than that. I crimp my bottleneck cartridges and I've read studies both ways regarding accuracy. However the crimp is also intended to prevent any bullet pushback from firing the gun as well. I try really hard not to over crimp. I've used the LEe die setup in the pat but don't any longer. I use the RCBS seater crimp die because I use a single stage press and I uniform my brass.

I'm doing the garage.

I've never really had success with the pocket swager tools. I've used a reamer from hornady or even the neck chamfer tool to ream the pockets.

I've used both the resizing die and the universal decapping die for live primers and I've never had an issue. I've done it because of bad brass where the primer is pressed in properly or when I've not reamed enough crimp and it gets side ways / distorted.

I applied quite a while ago and just heard back. It was actually sooner than I expected. I've elected to attend the January meeting as required. I know if accepted you are probationary for some period of time. I was wondering what are the requirements for full acceptance? I'm a pretty reserved guy and a stickler for safety. I have no issues following rules and I'm always respectful of other folks. I really want to make a first and positive impression. I'm sure I'd be a good member of the club. Thanks Rob

I have one of these for my .308 build. It's an awesome rail.

Sig 516 is tough to beat for about 1500 and it has one of the best piston systems out.

These ship for free from cabelas. I'm not sure which is a better safe.

Make sure you started counting the day after you picked up your last gun or 31 days including the day you picked up your last gun. Congrats you'll love the gun.

Anyone have an opinion on this one? It's 200 off when you add to cart--so 499.00. http://www.dickssportinggoods.com/product/index.jsp?productId=21661616&prodFindSrc=cart

For those of you with golden rods, dehumidifiers, etc, did you drill a hole in your safe for the plug?

It's worth it to take care if your kids but you already know that. Sounds great.