raz-0

If there were amitigating circumstance here, it would be the other employee's life being at risk.

OK, the QMS is going to pull about 6lbs +, the ACT is going to pull about 5-6lbs. Take the ACT and put in JP 3.5 tactical springs and it should pull about 5lbs even, be smooth, very reliable, and reset well. It's what I put in my wife's rifle as my 2.5-3.5lb trigger scare her a bit.

From the looks of it, I would not risk it. I might be willing to have the argument if the method by which it reduces flash were not the same as an a2 flash hider which is a no-no. It just looks like it does less of it while trapping and redirecting gasses with the backwards velocity stack.

it means saving the new episodes for sweeps in february. Sweeps are when Nielsen collects the ratings info. fall sweeps have closed. Next sweeps is february into the first week of march. TWD doesn't make enough shows to worry about may sweeps.

Is it slam firing, or are you bump firing it with a light trigger? That's a MUCH more common scenario I ahve found with .308 and above semi autos. Bump firing like that is jsut poor technique (or a a matter of a specific kind of flinch).

It's not the same.

It was an issue of domestic violence. The one category of violent crime where guns don't lead the pack. Odds are without a gun, the only thing that would have changed is either that he wouldn't have offed himself successfully, or he wouldn't have done so in front of co-workers. Anti-gun is one thing, anti-gun while ignoring the nature of the crime is another.

Unless you have a plan for cleaning the deivce you have on there, keep this in mind. FYI, the rainier short comp leaves the crown exposed and you can reach everything to clean it. It's also marginally effective as a comp for .223, so the fact that you aren't asking much of it is a good thing.

If you have lean hands, slide bite shouldn't be a problem. If you have meaty hands, it can.

Jam a dowel into the magazine from the top and whack the dowel with a hammer. At least if your mag has a welded baseplate.

If stuff is missing, go straight to the mail cops. https://postalinspectors.uspis.gov/forms/mlntrcvd.aspx

The NRA loves creating an echo chamber. Like the stupid UN small arms treaty crap they spewed without regard for the actual situation. They don't really have a history of seeding pointless crap without their name attached. Their current AWB scare is that one simply must be coming. Just like this list has nothing to do with obama, this article has nothing to do with the NRA. If it were it would read more like ap press release than some shitty chain email letter threatening you with brand X flavored doom if you don't forward it.

Except the NRA has nothing to do with the idiot bloggers dredging up old news.

In some states there are different definitions for things like machine guns, sbrs, etc. than the federal definition. I think he was just being clear and specific. I.e. legal federally, and legal in nj, thus legal for the op.

Oh no, I concern myself greatly with new gun legislation. What I'm getting sick of are people spreading bs like they are frikin paul revere announcing news that is months or years old without bothering to check anything. It does NOT help to argue lies. Period. Nobody seems to like it when the anti's do it, then you shouldn't do it yourself. There's no need to, there's plenty to talk about, it's just not as simple as "another AWB is coming". I find this stuff especially annoying because I'm CERTAIN that at the very least, there will be a new ban bill or two submitted to committee under Obama's second term. How it goes in committee is going to be very telling of the party politics on the Democrat side of things. If badly written bills like the McCarthy one the uninformed wackadoodle shit stirring segment of is pushing around hits, and it gets out of committee, be very very afraid. IT likely won't pass with no grandfathering because it would cost a massive sum to compensate for property, but it means there would be legs for any more reasonable version and it will be VERY, VERY necessary to get the grass roots level lobbying of congressional reps going hard to hope to stop it. It would answer the question of "is it Obama's plank, or the Party's plank?"

I think it was the 28". Whatever comes on the field model. Only work I had done was cut, thread for choke, had the forcing cone lengthened, and install the sites I sent in with the barrel. I think it cost about $139 with shipping. Something like that. I installed the tube, rail, sidesaddle and clamp myself.

this is my customized 930 cut down to 18.25" with a nordic +2 extension with their extended cap. I did this because I put in an anti-tilt follower with an extended tail. If you load short european shells or short reduced recoil slugs, it gets close to fitting 7, but doesn't by about 0.3" for the shortest shells I can dig up. The factory 18" barrels are really 18.5", and the stock nordic cap is about 3/4" shorter than what is on mine.

It's more than likely your credit card company. They don't give you those things out of a sense of charity, it's to make money. One of the ways they make money is selling your info. I bought my first from a small place, but their primary business was selling firearms, and it was in the business name. NRA stuff and catalogs started showing up in a matter of days.

Uhh it is a bunch of shit stirring. It's just the list from HR1022 proposed by CArolyn McCarthy back in 2007. The article says so, though it tries to be obtuse about it, and the content doesn't agree with the headline. That's some leaking there. A public document, submitted to committee a full five years ago, where it died, while the committee was run by a majority of gun grabbers, while the dems controlled congress, and while Bush was sitting and said he would sign any AWB renewal that hit his desk. Holy crap, circle the wagons this is some breaking news about critically urgent stuff happening this very minute.

Ok do what are those revolvers? Very pretty.

I've always had good service from my carriers. The "help" behind the counter is a different matter.

Really overgassed ars will cycle so fast they outrun the magazine spring, and fail to strip rounds and lock back.

<p>Sdhc is great. Sdxc is problematic, especially with the larger cards. They are supposed to use the exFAT file system, and support for it is spotty. Pretty much all my existing card readers don't support it even after driver updates. in theory my Samsung galaxy s3 for work supports sdxc, but the 64gb cards don't work unless you reformat them just using fat32 because the exFAT implementation is incomplete for the phone. I have a MacBook pro that reads it fine under osx, but under windows 7 via boot camp, it doesn't even see the card. This is with a 64gb card. Sdxc isn't necessarily faster than sdhc or sd, it all depends on the speed rating of the individual card. It is a capacity spec. sd maxes at 2gb (in reality they made 4gb cards, but compatibility was questionable)Sdhc maxes at 32gb. Sdxc goes up to 128gb currently, but I believe the ceiling for it with exFAT is pretty large.

It depend on the mechanism by which their cells function. The extreme pressures can do weird things to protein chains if you don't have the right genes. If their cells could function, it'd be a matter of making the walk. There's some deep holes down there that would take a lot of zombies to fill them enough to make the accessible to the shambling masses.

Round counts will be kept lower for time. 250 should cover missing a bit and a reshoot.