Everything posted by Pew Pew Plates
-
The use of the word Brother
My first day of union ironworking I had someone introduce me to another random dude as my "brother" . I was thinking, "WTF this isnt my brother?!" and then he noticed my confused look and clarified we were from the same hall LOL
-
.356 vs .355 9mm bullets
I dont think so, they have enough strength to resist scraping I do believe. However, I dont know why you would want to spend nearly the same amount of $ for a less accurate more difficult to load bullet. Just get the MGs
-
.356 vs .355 9mm bullets
MG is a superior, true jacketed bullet. I believe the size difference is because plated bullets are loaded to lead specs, and they act like lead in the barrel so they are typically bigger to swage down in the bore.
-
SCFGPA
It should be as simple as showing up to a meeting and voting on it
-
.22 Spinner question
I agree on the prices, and I also dont think he can compete with the cheaper ones. While it can be made with scrap steel cutting the shapes, cleaning them up, twisting the circle targets takes alot of time. Its not worth his time
-
Don't get pulled over leaving NJ
If you get pulled over, you dont have to tell them anything about where you are going or coming from. Dont speak about your origin or destination without first consulting a lawyer, even if it means sitting in a cell overnight.
-
Transporting from your apartment to your car
It pisses me off that we even have to wonder such things in this state
-
watched a random nutnfancy vid
http://www.everydaynodaysoff.com/2010/02/06/nutnfancy/
-
Issues with Hornady Critical Defense .357
OK, so this myth (have seen it many times before) states that the crud is basically crimping the front of the round down, and makes high pressures. Ring of crud cannot raise pressures much at all. Think about crimping for a second (which is safe and doesnt blow out primers etc etc). If you reload a round, and you crimp it, think amount how much force you exert on that lever. Not only do you have ~18" of mechanical advantage, but you have to consciously give it a good tug. For it to raise pressures beyond that, you would have to logically be exerting even MORE force on the .357 as you load it into the dirty chamber, with NO mechanical advantage, in order to exceed the pressures a crimp makes! (You cant physically provide enough force with your fingers). Ring of crud can make difficult extraction. It will NOT make high pressure. This is how yet another internet myth is debunked.
-
Cleaning with attached Brake
Hey, to each his own. WD40 wont affect your accuracy, infact, I think nothing short of putting rocks in your barrel will with an AK, but WD40 is bad because of how it reacts to fouling, especially in the gas system. Never said you wont be able to shoot at 200 yards because you use WD40. Usually the best cleaning they get over the pond is a piece of string with a knot tied in it soaked in motor oil pulled through the bore and the reciever wiped out, and the rifle doesnt seem to care (notice they dont pull it through the gas system though!)
-
Q about 9mm ammo
Reason? For the record, wolf if more accurate than alot of other range ammo, including winchester and CCI. The steel casings are not made of steel as hard as your gun, they are made from soft mild steel, which is also coated, so dont use the whole "it will wear out my gun" thing. Not gonna happen!
-
Cleaning with attached Brake
It really doesnt take much at all. Its alot easier than you would think with a .22! Take a cleaning rod, loosed the attachment so there is a slight gap, put it through the chamber end and pull it back out. Watch what happens when that gap catches the crown. Ask me know I know. The nick can usually be lapped out.
-
Ruger 1022 Stocks
You could always go classic with an M1 carbine stock & tech sights
-
Cleaning with attached Brake
When you use a copper solvent, use a tight patch of a slotted patch holder, not a jag, and work it back and forth ~10 times or so each patch untill discoloration stops or slows. This cures your over-enthusiastic jag use. Hate on the boresnakes? They have a place, namely, on a .22 that you cant clean from the chamber end. .22s have fragile crowns and in conjunction with small bore diameter, I would never put a rod down the muzzle. If you cant get a rod in either way, well, I guess boresnake it is thats what I use on my 10/22
-
Cleaning with attached Brake
You should never ever ever ever ever put WD-40 on your gun, let alone in the gas system! You should NEVER put ANY oil ANYWHERE in the gas system of ANY gas operated firearm! Especially not WD! There is a very slight chance of "Dieseling", not to mention the fouling that will happen due to oil in the system will be super nasty and far more detrimental to the gun (and you...) than just leaving it dry. After the first shot there is no lubricity to the oil you put in there, it is just tar that is much harder to remove than the fouling would be if you left it dry. If you feel like its going to rust, put a very light film of oil (not WD-40...) and wipe it off. I shoot corrosive, and keep my rifle in a non-climate controlled safe, and I have no problems with leaving the gas system totally dry after rinsing it out with warm soapy water.
-
Cleaning with attached Brake
If you are carefull, you should be able to avoid striking the crown. Depending on how flexable your rod is, you may actually be able to clean it from the rear. Boresnakes suck, so dont even go that route. You shouldnt be going in too much with the jag itself, what I do is I do 10 passes with a solvent soaked brush, jag untill clear (this is usually only 2-3 passes) then I will use a slotted patch holder with copper solvent untill clear, then dry patches and oil. Since you are not really using the jag much it shouldnt be a problem to go slow and be careful. Will a strike from an aluminum jag mess it up? I dont know, the slightest nick on the edge will screw up accuracy, but then again, would you ever notice on an AK? I'de be more concerned if it was a precision bolt gun, lol...
-
Cleaning with attached Brake
I dont think you guys understand what a crown is. If the crown is bigger than the diameter of the bullet, then you have a worn out muzzle! Saying that the crown is supposed to be bigger than bullet diameter is like saying the outside diameter of the barrel is smaller than the bullet. It makes less sense than calling a mag a clip!
-
Blowing Up an AK, Just for Fun
I effin' love it. Here is an AK running %100 on 32 grains of black powder. I'de like to see an AR gas system take that! http://www.surplusrifleforum.com/viewtopic.php?f=40&t=79976
-
handgun number 2
Knowing what you already have will also help. If you already have a plastic fantastic, I'de get the M92FS. If you already have a full sized heavy pistol, I'de get the XD. If you have a gun that kinda fits both roles (a full sized plastic) I'de get the DE for giggles. If it was me, I'de get neither of your choices but thats just me
-
handgun number 2
My choice is D.) All of the above
-
Marlin 795
I can ring a plate about 6" wide by 10" tall offhand with tech sights at 100 yards like its my job! (10/22) I have the flip up tech sights, so I have a 25 yard zero and then I just flip it back and its a ~100 yard zero. The sights are more capable then the rifle, people use this style of sights to shoot 600 yards regularly
-
Black Powder Meetup
Good fun had by all! Nobody ever shoots BP there, so having 3 guys lighting off BP pistols indoors sure attracted attention LOL
- Trap shooting 1st time
-
Trap shooting 1st time
For clay sports, an over under cant be beat. Easier to clean than an auto, less complex than both pump and auto, with a single trigger they are actually faster than an auto, you can have 2 different chokes on at once and select between them, will never jam, dont throw the shells on the ground or onto the shooter next to you, oh yeah, and they are awesome looking lol. You will never be presented more than 2 clays at once so you are not disadvantaged there. Avoid: mossberg, stoeger, and ruger over unders. Best bang for the buck is CZ. Brownings are next in line with the Citori and Cynergy. Caliber is up to you, but if you can handle a 12 you may as well use one. You can always get a tube set to shoot subgauge if you so desire, or download 12ga to subgauge specs.
-
SHTF AR-15 almost done...
Looks like the bottom rifle is better equipped for SHTF